DLA A-A-59440 11-2012 VALVE SWING CHECK-VALVE STEAM.pdf

《DLA A-A-59440 11-2012 VALVE SWING CHECK-VALVE STEAM.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59440 11-2012 VALVE SWING CHECK-VALVE STEAM.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 4820 A-A-59440/11 5 December 2012 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET VALVE, SWING, CHECK-VALVE, STEAM The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring the valve,

2、 swing, check-valve, steam described herein shall consist of this document and the issue in effect of A-A-59440. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This Commercial Item Description (CID) specification sheet uses a classification system which is included in the PIN as shown in the fo

3、llowing example (see NOTES). AA59440 /11 - 050 CID number Applicable Dash number CID spec sheet (see figure 1) (two digits) SALIENT CHARACTERISTICS. Interface and physical dimensions. Valve, swing, check-valve, steam supplied to this CID specification sheet shall be as specified herein (see figure 1

4、). Size. Nominal sizes of 1/4 inch through 1 inch with NPTF-1 threads. Intended application. This item is for use in steam systems where pressures do not exceed 150 psig (10.3 bar) Steam at 351 F (177.2C) and the steam is compatible with brass. Permissible variations in dimensions. Figure 1 lists th

5、e permissible variation in dimensions for each size. The external dimensions of the valve should not limit procurement unless the end item applications restrict these dimensions. Optional designs. Figure 1 is for identification purposes only and is not intended to restrict designs or shapes not dime

6、nsioned. Threads. Threads are dryseal NPTF-1 in accordance with CID A-A-59440. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/11 2 Materials. Preferred valve material. Preferred material is brass in accordance with ASTM B61. Bra

7、ss. Brass shall be in accordance with the following: ASTM B16/B16M ASTM B121/B121M ASTM B505/B505M SAE AMS4845 ASTM B22 ASTM B124/B124M ASTM B584 SAE AMS4855 ASTM B30 ASTM B148 ASTM B763 SAE AMS4860 ASTM B36/B36M ASTM B176 ASTM B770 SAE AMS4862 ASTM B61 ASTM B271 SAE AMS4890 ASTM B62 ASTM B369 Prote

8、ctive Coating. Brass: None. Caution: Brass with lead contents shall not be used for potable or oxygen systems. Mounting. Mounting shall be vertical with upward flow direction so as to push against the swing. Pressure. Working Pressure: 150 psi (10.3 bar). Test Pressures. Perform tests in accordance

9、with A-A-59440 using API Standard 598. a. Shell test pressure 275 psig (19.0 bar). b. Certification of testing can be used in place of testing if procuring activity accepts. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/11 3 Dash number N

10、ominal pipe size A Pipe tread, NPTF-1 B Ref C Ref 050 1/4 1/4 - 18 2.25 1.75 051 3/8 3/8 - 18 2.25 1.75 052 1/2 1/2 - 14 2.50 1.75 053 3/4 3/4 - 14 3.00 2.00 054 1 1 11 1/2 3.50 2.38 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specifi

11、ed tolerances are .010 inch (0.25 mm). 4. Oval port having same cross sectional area is acceptable. 5. Measurements across flats of hexagonal wrench pad shall be a standard measurement. FIGURE 1. Valve, swing, check - valve, steam. Provided by IHSNot for ResaleNo reproduction or networking permitted

12、 without license from IHS-,-,-A-A-59440/11 4 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents Commercial Item Description A-A-59440 - Cock-Valves and Valve

13、s, General Requirements For (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) American Petroleum Institute API Standard 598 - Valve Inspection and Testi

14、ng (Copies of this document are available online at http:/www.api.org/Standards/ or from American Petroleum Institute, 1220 L Street, NW, Washington, DC 20005-4070, Tel: 202-682-8000.) ASTM INTERNATIONAL ASTM B16/B16M - Free-Cutting Brass Rod, Bar and Shapes for use in Screw Machines ASTM B22 - Bron

15、ze Castings for Bridges and Turntables ASTM B30 - Copper Alloys in Ingot Form ASTM B36/B36M - Brass Plate, Sheet, Strip, and Rolled Bar ASTM B61 - Steam or Valve Bronze Castings ASTM B62 - Composition Bronze or Ounce Metal Castings ASTM B121/B121M - Leaded Brass Plate, Sheet, Strip, and Rolled Bar A

16、STM B124/B124M - Copper and Copper Alloy Forging Rod, Bar, and Shapes ASTM B148 - Aluminum-Bronze Sand Castings ASTM B176 - Copper-Alloy Die Castings ASTM B271 - Copper-Base Alloy Centrifugal Castings ASTM B369 - Copper-Nickel Alloy Castings ASTM B505/B505M - Copper Alloy Continuous Castings ASTM B5

17、84 - Copper Alloy Sand Castings for General Applications ASTM B763 - Copper Alloy Sand Castings for Valve Applications ASTM B770 - Copper-Beryllium Alloy Sand Castings for General Applications (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O.

18、Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59440/11 5 SAE INTERNATIONAL SAE AMS4845 - Tin Bronze Castings, Sand and Centrifugal 87.5CU - 10SN - 2ZN as Cast SAE AMS4855 - Lea

19、ded Red Brass, Sand and Centrifugal Castings 85CU - 5.0SN - 5.0PB - 5.0ZN as Cast SAE AMS4860 - Manganese Bronze, Sand and Centrifugal Castings 58CU - 39ZN - 1.2FE - 1.0AL - 0.80MN as Cast SAE AMS4862 - Manganese Bronze, Sand and Centrifugal Castings 63CU - 24ZN - 6.2AL - 3.8MN - 3.0FE High Strength

20、, as Cast SAE AMS4890 - Copper-Beryllium Alloy Castings 97CU - 2.1BE - 0.52CO - 0.28SI Solution Heat Treated (TBOO) (Copies of these documents are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 inside USA and Canada o

21、r 724-776-4970 outside USA, email at CustomerServicesae.org.) MILITARY INTERESTS: CIVIL AGENCY AND COORDINATING ACTIVITIES: Custodians: GSA - FSS Army - AR Navy - SH Air Force - 99 Preparing activity: DLA - CC DLA - CC Review activities: Army - AT, CR4, GL, MI (Project 4820-2012-006) Navy AS, MC, SA

22、 NOTE: The activities listed above were interested in this document as of the date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-