DLA A-A-59252-1998 ETCHERS ELECTRIC PORTABLE 120-VOLT A C [Superseded NAVY MIL-E-3118 C CANC NOTICE 2 NAVY MIL-E-3118 C VALID NOTICE 1 NAVY MIL-E-3118 C (1) NAVY MIL-E-3118 C NAVY .pdf

《DLA A-A-59252-1998 ETCHERS ELECTRIC PORTABLE 120-VOLT A C [Superseded NAVY MIL-E-3118 C CANC NOTICE 2 NAVY MIL-E-3118 C VALID NOTICE 1 NAVY MIL-E-3118 C (1) NAVY MIL-E-3118 C NAVY .pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59252-1998 ETCHERS ELECTRIC PORTABLE 120-VOLT A C [Superseded NAVY MIL-E-3118 C CANC NOTICE 2 NAVY MIL-E-3118 C VALID NOTICE 1 NAVY MIL-E-3118 C (1) NAVY MIL-E-3118 C NAVY .pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、a INCH-POUND A-A-5 9252 June 16.1998 SUPERSEDING 12Februa1y 1974 MIL-E-3 1 18C COMMERCIAL ITEM DESCRIPTION ETCHERS, ELECTRIC, PORTABLE, 120-VOLT A.C. The General Services Administration has authorized the use of this commercial item description for ail Federal agencies. 1. SCOPE. This commercial ite

2、m description (CID) covers electric etchers of electric arc and vibrating point type. 2. CLASSIFICATION. Electric etchers covered by this CID are of the following types as specified (see 7.2). Type I - Light duty etcher, 500 watts. Type II - Heavy duty etcher, 1,000 watts. Type III - Heavy duty etch

3、er, vibrating type. 3. SALIENT CHARACTERISTICS. 3.1 Description. Type I and II etchers shall consist of a case, transformer, control panel, power ?on-off switch, power cable with plug, etching tool lead, etching tool or stylus, ground clamp, and a ground plate when funiished. Type I etchers shall co

4、nsist of a drive unit, reciprocating shafl, collet or chuck, switch, power cable, and replaceable etching points. Etchers shall operate on 120 volts (rated voltage), 50 to 60 Hertz, alternating current (AC). Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any dat

5、a which may improve this document should be sent to: officer In Charge (Code 15E2), Seabee Logistics Center, 41 11 San Pedro St., Port Hueneme, CA 930434410, by using the Standardization Document Improvement Proposai (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 513

6、0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59252 = 90L054 0000600 Ob3 m A-A-5 9252 3.2 Standard commercial product. The etchen shall, as a minimum be in accordance with this CID and shall be the manufiadurers standard commercial product. A

7、dditional or better features which are not specifically prohibited by this CID but which are a part of the manufacturers standard commercial product, shall be included in the etchers being furnished. A standard commercial product is a product which has been sold or is being currently offered for sal

8、e on the commercial market through advertisements or manufacturers catalogs, or brochures, and represents the latest production model. 3.3 Desim. The etcher shall be designed to etch on metals by the electric-arc process for types I and II and vibratov-scariEyrng process for type III. 3.3.1 Insulati

9、on resistance. Insulation of the etcher shall be dielehc. 3.3.2 Plugs. Plugs on etcher power cables shall be rated at not less than 15 amperes, 125 volts. 3.3.3 Fastening devices. All screws, pins, bolts, and similar parts shall be installed with means of preventing loss of tightness. All such parts

10、, when subject to removal or adjustment, shall not be swaged, peened, staked, or permanently deformed. 3.3.4 Power cable. The power cable for etchers shall be not less than 5-foot (1 524 millimetre (mm) lengh of commercial type, threeanductor cable of suitable size. The cable shail be equipped with

11、the plug specified in 3.3.2. The length of cable shall be measured from the point of entry into the tool. 3.3.5 Types I and II. 3.3.5.1 Heat output. Type I and II etchers shall be capable of operating for 30 minutes at heat output of 500 to 1,000 watts respectively in “oI and “off duty cycles. The t

12、ransformer temperature shall be not greater than 149 degrees Fahrenheit (OF) (65 degrees Celsius (OC) above ambient. The etching point shall withstand the heat developed without distortion or blunting of the tip. Type I shall have not less than 3 heat-taps. Type II. shall have not less than 10 heat-

13、taps with not less than three taps below 300 watts. 3.3.5.2 Weight. The weight of type I and II etchers shall be not greater than 25 and 3 5 pounds (1 1.34 and 15.88 kilogram (kg), respectively. 3.3.5.3 Case. The case of type I and II etchers shall be made of sheet steel. The base of the case shall

14、have five embossed dimples of not less than 0.375-inch (9.53 mm) spherical radius that shall raise the inside base of the etcher case. Alternatively, rubber pads of not less than 0.875-inch (22.23 mm) diameter by 0.375-inch (9.53 mm) thick may be substituted for the dimples. The pads shall be aached

15、 with locked screws. The case shall be equipped with a handle with a hand grip. Space shail be provided within the case for stowage of the power cable, etching tool with spare points, etching point and ground leads, and a pund plate when furnished. Altematively, an integral part of the case, suitabl

16、e for use as a ground for the etching tool, may be substituted for the ground plate (see 3.3.5.8). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-59252 9038054 O000603 TTT A-A-5 9252 3.3.5.4 Transformer. The transformer shall be designed for

17、the duty specified herein on a rated input voltage of not less than 120-volts AC, without creating a fire hazard. The transfomer shall be mounted rigidly and securely in the etcher case so that the transformer shall not become loosened or detached from its mounting. The use of an adhesive for mounti

18、ng shall not be acceptable. 3.3.5.5 Control panel. The control panel shall have an indicator light to indicate when power is on, two output terminal studs, an “on” and “off power switch, and a rotary heat-tap selector with a pointer and legible dial for indicating the applicable heat-taps (see 3.3.5

19、.1). The output terminals shall be insulated to prevent any grounding through the hole cross sectional and panel surface areas. 3.3.5.6 Etching tool and ground leads. Etching tool and ground leads shall be not less than 3-foot (914.40 mm) length of suitable size of insulated wire cable. Each lead sh

20、all be equipped with a spade-type copper terminai at one end for connection to the transformer terminal studs. An etching tool shall be attached to the other end of the etching tool lead and a positive-type grounding copper terminal shall be attached to the other end of the ground lead. 3.3.5.7 Etch

21、ing tool. The etching tool or stylus shall have an insulated holder of suitable size and shape for ease of handling and a replaceable etching point. The tool shall be provided with a spare etching point. 3.3.5.8 Ground plate. The ground plate of type I and II etchers, when furnished, shall provide e

22、lectrical conductivity and have not less than a 25 square inch (16 129 square millimetre) surface area. 3.3.5.9 Graund clamp. The ground clamp of type I and II etchers, when furnished, shall provide electrical conductivity for etching large parts that cannot be conveniently placed on the ground plat

23、e. 3.3.6 Type III. The type III etchers shall be capable of operating continuously for one-hour so that the etching points shall withstand shock (see 3.3.6.6) without fracturing, bending or twisting. 3.3.6.1 Weight. The weight of type III etcher shall be not greater than 1-pound (0.45 kg). 3.3.6.2 D

24、rive unit. The drive unit shall consist of a heavy duty vibrating unit. The housing shall be sized and shaped to provide a comfortable hand-grip and shall have a power switch. The etcher shall operate to provide the specified speed for the reciprocating shaft (see 3.3.6.3). 3.3.6.3 Reciprocating sha

25、ft. The reciprocating shaft shall be mounted in a heavy duty sealed bhng. The shaft shall reciprocate at not less than 7,200 strokes per minute. 3.3.6.4 Chuck. A collet or chuck shall be located on the reciprocating shaft and shall accommodate replaceable etching points. 3 Provided by IHSNot for Res

26、aleNo reproduction or networking permitted without license from IHS-,-,-A-A-59252 3.3.6.5 Switch. The “on-off switch on the motor housing shall be placed in a convenient location for the operator. The switch shall be toggle, slide, or rocker-type, and shall be installed as part of the housing config

27、uration. 3.3.6.6 Etching points. The etching points for type III etchers shall be wear- and shock-resistant. The etcher shall be fimished with six alloy steel etching points consisting of two with diamond tips and four with tungsten carbide tips. 3.4 Finish. Etchers shall have enameled or plated fin

28、ishes on metal surfaces in accordance with manufacturers standard commercial practice, except in no case shall cadmium plating be used. 3 S Identification plate. A corrosion-resistant metal or plastic identification plate, permanently and legibly marked with the following information, shall be secur

29、ely attached to the etcher: Manufacturers name. Manufacturers model or serial number. 120 volts. 5060 Her AC only. 3.6 Fungus. When specified (see 7.2), the elecical circuitry, including all components and connecions, shall be protected fiom the effect of water and fungus growth by an overall treatm

30、ent with a siandard commercially accepted varnish with the following exceptions: a. Components or circuit elements which are inherently fungus and water resistant or which are hermetically sealed, need not be treated. b. Components or circuit elements whose function will be adversely affected by the

31、 varnish coating shall not be treated. 4. REGULATORY REQUIREMENTS. 4.1 Materials. The offeror/conmtor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation AR). Unless otherwise specified herein, all equi

32、pment, matenal, and articles incorporated in the work covered by this commercial item description are to be new and fabricated using materials produced hm recovered materials to the maximum extent possible without jeopardizing the intended use. The term “recovered materials” means materials which ha

33、ve been collected or recovered fiom solid waste and reprocessed to become a source of raw materiais, as opposed to virgin raw materiais. Unless otherwise specified, none of the above shall be interpreted to mean that the use of used or rebuilt products are allowed under this commercial item descript

34、ion. 4.2 Metric products. Products manufctured to metric dimensions will be considered on an equal basis with those rnanufbctured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest version of ASTM SI-10 (EEHASIM SI-lo), and all othe

35、r requirements of this commercial item description including 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c r A-A-59252 m 9038054 0000b03 872 m A-A-59252 form, fit and hction are met. If a product is manufactured to metric dimensions and those d

36、imensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product conformance. Th

37、e products provided shall meet the salient characteristics of this commercial item description, codorm to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to re

38、quire proof of such conformance. 6. PACKAGING. The preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 Source of documents. 7.1.1 The Federal Acquisition Regulation AR) is available from the Superintendent of Documents, U.S. Government Printing Ofice, Was

39、hington, DC 20402. 7.1.2 ASTM Standard is available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. 7.1.3 IEEE Standard is available fim the Institute of Electrical and Electronics Engineers, IEEE Service Center, 445 Hoes Lane, P.O. Box 1

40、33 1, Piscataway, NJ 08855-133 1. 7.2 Ordering data. Acquisition documents should speciQ the following: a. Title, number, and date of this CID. b. Type required (see 2.). c. When fungus protection is required (see 3.6). 7.3 Suuersession data. This CID replaces Miliary Specification MIL-E-3 118C, dat

41、ed 12 February 1974. 7.4 Part Identification Number PIN) . The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. The PIN to be used for items acquired to this description are created as follows: AA59252 - X CIDnumbe

42、ri T Type code I 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59252 9018054 0000hOLl i09 W A-A-5 9252 7.5 Metric units. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the

43、SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system should be used independently of the other. Combining values fiom the two systems may result in non-conformance with the standard. 7.6 Subiect tem (key word) listing. Engrave Identificat

44、ion Inscribe Marking Stylus 7.7 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: custodians: Navy - YD1 hy-GL Air FOIW - 99 Review Activities: Navy - AS, SH GSA - FSS Premring: Activitv: Navy - YD1 (Project 5130-0400) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-