DLA A-A-55284-1995 BUCKLES BRASS《铜管扣环》.pdf

《DLA A-A-55284-1995 BUCKLES BRASS《铜管扣环》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55284-1995 BUCKLES BRASS《铜管扣环》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55284 W 9999974 0368786 513 H A-A-55284 September 26, 1995 COMMERCIAL ITEM DESCRIPTION BUCKLES, BRASS The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-B- 17910D and MIL-B-20588F for all Federal agencies. 1. - SCOPE. This comm

2、ercial item description covers buckles intended for use with the mens coat belt or the military police belt. 2. CLASSIFICATION. The buckles shall be of the following classes and types: Class 1 - Solid polished brass (Marine Corps) Type I - Red brass Type II - Yellow brass Class 2 - Die cast zinc and

3、 aluminum alloy with chrome- plated finish Class 3 - Die cast zinc and aluminum alloy with brass- plated finish Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Defense Personnel Support Center, Clothing

4、and Textiles Directorate, Attn: DPSC-FQSE, 2800 South 20th Street, Philadelphia, PA 19145-5099. I AMSC N/A FSC 8315 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-

5、5 52 8 4 3. SALIENT CHARACTERISTICS. The class 1, type I buckle shall be 1-3/16 x 2-5/32 x 3/32 inch (+1/64 inch), and the corners and edges shall be slightly beveled, The thickness of the outside vertical portions of the body shall be .250 (k.005) inch. The thickness of the outside horizontal porti

6、ons of the body shall be ,156 (k.005) inch. The thickness of the inside vertical bar shall be .187 (2,005) inch. The class 1, type II buckle shall have outside dimensions of 2 x 2-5/16 x 1/8 inch (+1/16 inch) and shall be of stamped construction. The inside dimensions of the buckle shall be 1-1/2 x

7、1-13/16 x 1/8 inch (+1/16 inch). The center vertical bar shall be 1/4 inch thick, and the tongue wire shall be .144 (k.005) inch in diameter. The class 2 and class 3 buckles shall have outside dimensions of 2-3/8 x 2-7/16 x 3/16 inch (+ 1/16 inch) and shall be of die cast construction. The inside di

8、mensions of the buckle shall be 1-3/4 x 1-13/16 x 3/16 inch (+1/16 inch). The center vertical bar shall be 7/32 inch thick, and the tongue wire shall be -144 (k.005) inch in diameter. Figures 1 and 2 are furnished for informational purposes only . 3.1 Materials 3.1.1 Class 1, tme I and type II. The

9、body of the type I buckle, made from copper alloy number 230 (red brass), and .the type II buckle, made from copper alloy number 260 or 268 (yellow brass), shall conform to ASTM B36 or ASTM B121 requirements. A cut-out shall be provided in the center bar of the type II buckle to retain the tongue in

10、 position in the center of the bar. The top surfaces and outside edges of the buckle body shall be polished to a uniform, mirror-like finish. The back shall have a satin finish. 3.1.2 Class 2 and class 3. The body of the class 2 and class 3 buckles shall be die cast from a zinc base alloy conforming

11、 to ASTM B86 requirements, Ribs shall be provided on the center bar to retain the tongue in the center of the bar. the class 2 buckle body shall be burnished to a smooth surface texture. The body shall then be copper plated followed by nickle plating and then by chrome plating. buckle body which are

12、 exposed to view when worn shall be polished to a uniform, mirror-like finish. The class 3 buckle body shall be prepared and plated in the same manner as the class 2 buckle; except, in lieu of chrome, the final plating shall be brass. After polishing, the body shall be coated with a clear, baked-on

13、epoxy lacquer. All surfaces of The top surfaces of the 3.1.3 The tonsue. The wire for the tongue (except class 1, type I) shall be fabricated from copper alloy number 260 and 270 conforming to ASTM B134, ASTM B159, or ASTM B206 requirements. When assembled to the buckle body, the tongue shall not bi

14、nd on the center bar; the tip of the tongue shall not protrude beyond the outer edge of the body, but shall protrude a minimum of 3/64 inch beyond the inner edge of the body; it shall not be possible by hand to slide the tongue out of the cutout in the center bar * t Provided by IHSNot for ResaleNo

15、reproduction or networking permitted without license from IHS-,-,- A-A-55284 = 9999974 0168988 396 D A-A-5 52 84 of the class 1 body (type II only) or over the ribs in the center bar of the class 2 and class 3 body; and the total lateral movement of the tongue tip shall not exceed 5/8 inch. The tong

16、ue for the class 1, type II buckle shall be brass dipped. tongue for the class 2 buckle shall be nickel-plated, followed by a lacquer coating. coated with a clear, baked-on epoxy lacquer. The The tongue for the class 3 buckle shall be 3.2 Label/markinq. All buckles shall be marked for identification

17、 with the manufacturers name or trademark. The marking shall be permanently affixed by stamping, etching, or casting on the back of the buckle and shall be legible. 4. REGULATORY REOUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accor

18、dance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY ASSURANCE PROVISIONS 5.1 Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description; conforms to th

19、e producers own drawings, specifications, standards, and quality assurance practices; and is the same product offered for sale in the comercial marketplace. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided

20、for under the provisions of the contract. 5.2 Market acceptabilitv criteria. The item offered, or a generic equivalent, must have been sold to the commercial market or to the Government for at least two years. 5.3 Warrantv. The item offered shall include the standard warranty given to the commercial

21、 market beginning with the date of delivery of the individual items. 5.4 Visual examination. Each buckle shall be examined for the defects listed below. 5.4.1 Defects. Not finished or type of finish not as specified; noticeable discoloration, corrosion, or stain; foreign matter embedded in finish of

22、 surfaces which are exposed to view when in use; surfaces exposed to view are abraded, scuffed, scratched, or not smooth; lacquered coating (where applicable) blushed, cloudy or not clear, not adherent, blistered, flaking or peeling, not continuous or level; coating not level, uniform, and continuou

23、s, e.g., runs, orange peel, wrinkles, drops, or streaks; plating (where applicable) is broken, cut through, corroded, or erupted; class 2 not chrome plated or plating has frosty area on surfaces exposed to view; distorted, bent, malformed, cracked, drag or step in construction and workmanchip; digs,

24、 gauges, burrs, nicks; 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55284 9999974 OLb8969 222 A-A-5 5 2 8 4 tongue fractured, malformed, bent or damaged, binds on center bar; tongue loop loose or open to an extent such that the tongue can b

25、e dislodged manually from its position on the center bar; marking missing, illegible, or not as specified; any items not packaged in accordance with the contract or purchase order. 5.5 Bid samles. Sample buckles shall be submitted for bid sample testing. for acceptability of color and finish. Finish

26、ed buckles shall match an approved sample 6, PACKAGING 6.1 Preservation, packins, and markinq. The preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES 7.1 Source of Government documents. Copies of military and Federal documents are available from: Standardizat

27、ion Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 7.2 Source of non-Government documents ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187. ) 7.3 Acceptance criter

28、ia. Acceptance criteria shall be as specified in the contract or purchase order. MILITARY INTERESTS: Custodians Army - GL Navy - MC Review Activities Army - MD CIVIL AGENCY COORDINATING ACTIVITY : GSA - FSS PREPARING ACTIVITY: DLA - CT I Project 83 15-03 9 O Provided by IHSNot for ResaleNo reproduct

29、ion or networking permitted without license from IHS-,-,-A-A-55284 9999974 OLb8990 T44 A- A- 5 5 2 8 4 fRONT TOLERAMCLS: + ?RACTIO.C(S - 1/84“ DECIMAL8 ?,008* MOTE: ALL CORMlRS AND LDQE8 SHALL BE 8LiHfLY 6EVILED BUCKLES, BRASS (Class 1, Type 11 FIGURE 1. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55284 9999974 OLb899L 980 A-A-5 5 2 8 4 SFCOMA-A 1 4 I t * BUCKLES, BRASS: Class l(TypelI), Class 2 & Class 3 FIGURE 2. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-