DLA A-A-55176-1993 BAG LAUNDRY NYLON《尼龙干洗袋》.pdf

《DLA A-A-55176-1993 BAG LAUNDRY NYLON《尼龙干洗袋》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55176-1993 BAG LAUNDRY NYLON《尼龙干洗袋》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55176 74 0141790 T45 I INCH-POUND I 5 March 1993 A-A-55 17 6 COMMERCIAL ITEM DESCRIPTION BAG, LAUNDRY, NYLON The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-B-21332. Abstract. This description covers the requirements for one typ

2、e of laundry bag fabricated from nylon duck material. The bags are intended for use by Naval personnel serving aboard ship for storing bedding, linens and clothing to be laundered. Salient Characteristics. The laundry bag shall be cylindrical in shape with a draw-string closure, and two carry handle

3、s, one on the side wall and the other on the bottom of the bag. Handles shall be cut from a piece of nylon cloth 12 inches (30.6 cm) - + 1/4 inch (6.4 mm) long by 5 inches (12.7 cm) t 1/4 inch (6.4 mm) wide for one bag handle. Fold piece in half lengthwise turning under raw edges and stitching lengt

4、hwise, 1/8 inch (3.2 mm) 2 1/16 inch (1.6 mm) from edge. When handles are attached to the bag the handle free opening shall be 6 inches (15.24 cm) _f 1/2 inch (12 mm). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document sh

5、ould be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DIST

6、RIBUTION STATEMENT A. FSC 8465 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 5 17 6 Finished dimension. The finished dimensions for the laundry bag shall be as follows: a. Length - 48 in

7、ches (121.9 cm) minimum (inclusive of b. Bottom diameter - 16 inches (40.6 cm) minimum (exclusive c. Width - 25 inches (63.5 cm) minimum (at top opening with bottom seam). of bottom seam). bag laid flat). Fiqure. The figure is furnished for information purposes only. To the extent of any inconcisten

8、cies between the written commercial item description and the figure, the written commercial item description shall govern. Materials Cloth, nylon. The nylon cloth shall be natural color, plain weave, 1 up and 1 down and shall conform to the physical requirements and test methods in Table I. TABLE I.

9、 - Physical requirements and test methods Characteristics Requirements Test methods Weight, oz. per sq/yd. (max 1 Yarns per inch (min) Warp Filling Yarn ply 2/ Warp Filling 7.25 ASTM-D 3776 Option C ASTM-D 3775 60 45 Breaking strength, lbs (min) Warp 325 Filling 275 Tearing strength, lbs (min) Warp

10、20 Filling 20 Visual 2 2 Colorfastness to: Light Laundering Dry cleaning Crocking Good Good Good 3.5 (min) ASTM-D 5034 ASTM-D 1424 AATCC 16 AATCC 61 AATCC 132 AATCC 8 2/ A single multifilament yarn of equivalent denier may be used. 2 Provided by IHSNot for ResaleNo reproduction or networking permitt

11、ed without license from IHS-,-,-A-A-5537b m 9999974 0343792 838 m A-A-55 17 6 Grommets. The grommets shall be rolled rim with spur washer, brass with bright finish size 2 or 3. Size 2 grommet, diameter after insertion (inches) shall be .375. Size 3 grommet, diameter after insertion (inches) shall be

12、 .438. Attach 8 grommets with washers, each shall be centered on hem and equally spaced round circumference. The grommet washer shall finish on the inside of bag. Holes punched to receive the grommets shall be smaller than the outside diameter barrel and shall be securely clinched without cutting th

13、e materials. Thread. The thread shall be a twisted multiple cord (ply) construction with a bonded or a soft finish size E. The color shall be natural white AG, Cable No. 66049. Draw-strinq. The draw-string shall be 1/4 inch (0.6 cm) diameter nylon rope conforming to MIL-R-17343. The draw-string shal

14、l be 8 foot (2.44 meters) length of rope (minimum) that has been seared and knotted at each end and shall be installed by threading through 8 grommets. Label/markinq. The label/marking shall be heat transfer (decalcomania) or direct printing, stamping, or stenciling. The bags shall be marked approxi

15、mately 3 inches (7.6 cm) below top edges of bags. The printing shall bear the following inscription: BAG, LAUNDRY (100% NYLON) NAME OF CONTRACTOR: CONTRACT NO.: DLA-100-00-0-0000 (Example) STOCK NO.: 8465-00-000-0000 (Example) Workmanship. The finished bags shall conform to the quality established b

16、y this commercial item description. Product Demonstration Model. When required, offerers shall submit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Ev

17、aluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items de

18、livered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted w

19、ithout license from IHS-,-,-A-A-55 17 6 Quality Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specifications, standards and quality assurance practices.

20、 The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all pro

21、ducts or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination. Bag lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control.

22、 Visual Examination. The bag shall be examined for the defects listed below. The lot size shall be expressed in units of bags. The sample unit is one bag. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 2.5. Defects.

23、The bag shall be examined for the following defects: any hole, cut, tear, smash, float, needle chew, mend, burn, drill hole, color not as specified; any spot or stain (outside); thread ends not removed; seams twisted, puckered or pleated; marking missing, incorrect, or illegible; measurement of item

24、 not as specified; handles missing or misplaced, free opening less than 5-1/2 inches (14.0 cm) or more than 6-1/2 inches (16.5 cm); grommets omitted, malformed, damaged, misplaced, clinched too tight cutting fabric, insecurely attached, not size, style or finish specified; rope end not seared or kno

25、tted; component missing, open seams, rope omitted, not as specified, not minimum length specified. Dimensional Examination. The finished bag shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be

26、 one bag; the inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55176 M 9999974 OL4L794 b0 D A-A-5s 17 6 Packaqinq Examination. The fully pa

27、ckaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 2.5. EXAMINE DEFECT Marking (exter

28、ior and interior) Materia 1 s Workmanship Content Palletization Omitted; incorrect; illegible; of improper size, location, or method of application Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strappin

29、g, improper taping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Requla

30、tory Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Preservation, Packinq, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. 5 Provided by IHSNot f

31、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55376 9999974 03431795 527 A-A- 5 5 1 7 6 Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 1

32、9111-5094 Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) ASTM-D 1424 - Tearing strength ASTM-D 3775 - Ya

33、rns per inch ASTM-D 3776 - Weight ASTM-D 5034 - Breaking strength (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Sources of Nonqovernment Documents - cont AATCC 8 - Colorfastness to Crocking: AATCC Crockmeter Met

34、hod AATCC 16 - Colorfastness to Light AATCC 61 - Colorfastness to Laundering, Home, and Commercial: AATCC 132 - Colorfastness to Dry-cleaning Accelerated (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC

35、27709-2215) Custodian: Navy - SA Civil Agency Coordinating Activity: GSA - FSS Preparing .Activity : DLA - CT Project No. 8465-0154 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55176 m 9999974 OL4L79b 4b3 m A-A- 5 5 17 6 BOTTOM VIEW FIGURE 1 - Bag, Laundry, Nylon 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-