DLA A-A-55162-1995 CONNECTORS ELECTRICAL SOCKETS SINGLE IN LINE MEMORY MODULE SINGLE AND DUAL VERTICAL TYPE 30 OR 60 CONTACTS《30或60触点单和双垂直型单列直插存贮模块插座电气连接器。》.pdf

《DLA A-A-55162-1995 CONNECTORS ELECTRICAL SOCKETS SINGLE IN LINE MEMORY MODULE SINGLE AND DUAL VERTICAL TYPE 30 OR 60 CONTACTS《30或60触点单和双垂直型单列直插存贮模块插座电气连接器。》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55162-1995 CONNECTORS ELECTRICAL SOCKETS SINGLE IN LINE MEMORY MODULE SINGLE AND DUAL VERTICAL TYPE 30 OR 60 CONTACTS《30或60触点单和双垂直型单列直插存贮模块插座电气连接器。》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55262 = 9999774 02b8202 358 METRI CI A -A - 55 162 23 June 1995 COMMERCIAL ITEM DESCRIPTION CONNECTORS, ELECTRICAL, SOCKETS SINGLE IN LINE MEMORY MODULE, SINGLE AND DUAL VERTICAL TYPE, 30 OR 60 CONTACTS The General Services Adninistration has authorized the use of this comnercial item descriptio

2、n (CID), for all federal agencies. 1. SCOPE. This CID covers the general requirements for a single or dual, vertical inline memory module connector with 30 or 60 contacts. This connector provides the user with convenient low insertion and easy extraction of high density memory modules which conform

3、to JEDEC specifications for SIMM modules. Connectors covered by this CID are intended for cmrcial/industrial applications. 2. CLASSIFICATION. This CID uses a classification Nunber (PIN) as shown in the following example (see AA55162 o1 I I I I CONTACT PLATING TYPE CID NUMBER system which is included

4、 in the Part or Identification 7.1). S I I S - SINGLE ROU D - DUAL ROW - .300 E - DUAL ROU - -400 3. Salient characteristics. 3.1 Desiqn. construction and dimensions. Design, construction and dimensions shall be as specified in accordance with figure 1, table I and shall accomnodate JEDEC configured

5、 SIMM memory modules. 3.2 Contacts. Code G contacts (dash number -01) are formed of a high conductivity, high strength copper alloy with gold over nickel plating in the contact area. Code T contacts (dash number -02) are formed of a high conductivity, high strength copper alloy with tin/lead plating

6、 over all areas. 3.3 Connector housing. of withstanding temperatures of vapor phase, infrared, or wave type soldering assembly processes. 3.4 Contact stress. 3.5 Misconnection. Built in polarization eliminates misconnection of SIMM module to connector. Additional polarization feature to align socket

7、 to printed wiring board for simplification of assembly. 3.6 Dielectric withstanding voltage. Uhen tested at 1,000 V ac, there shall be no breakdown of insulation or leakage current in excess of 5 mA between adjacent contacts for one minute. 3.7 Owrating temerature. The operating temperature range s

8、hall be from -55C to +105“C. Connector housings are made from high temperature thermoplastic material capable The connector design provides anti-stress protection for contacts. Beneficial comnents, recmndations, additions, deletions clarifications, etc. and any other data which may improve this docu

9、ment should be sent to: Defense Electronics Supply Center, ATTN: DESC-ELDI, 1507 Uilmington Pike, Dayton, OH 45444-5765, or telephone (513) 296-5391, or facsimile (FAX) (513) 296-8868. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5935 Provided by IHS

10、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55162 9999974 01b8103 294 A- A- 55 162 TABLE I. Dimensions. r . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-553b2 9 9999974 O368304 120 A- A- 55 162 FIGU

11、RE 1. Printed board layout. 3.8 Vibration. The connector, or hardware when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening of parts when subject to vibration of 10-55-10 Hz traversed in 1 minute at .O6 inch total excursion for 2 hours in each of 3 mutually p

12、erpendicular planes. 3.9 Physical shock. The connector or hardware when assembled to the connector, shall exhibit no evidence of breaking, cracking, or loosening of parts when subject to 50 gs saw-tooth wave shock of 11 milliseconds duration, 3 shocks in each direction applied along the 3 mutually p

13、erpendicular planes for a total of 18 shocks. 3.10 Durability. without a reduction in connector performance. 4. REGULATORY REQUIREMENTS. 5. QUALITY ASSURANCE PROVISIONS. 5.1 Responsibility for inspections. The contractor is responsible for the performance of all inspection, examination and test requ

14、irements specified in the contract or purchase order. The contractor may use his or any other facilities suitable for inspection requirements specified in the contract or purchase order, unless otherwise disapproved by the procurement activity. The procurement activity reserves the right to perform

15、any of the inspections set forth in the contract or purchase order where such inspections, examinations and tests are deemed necessary to assure supplies and services conform to prescribed requirements. The connector shall be capable of withstanding 25 module insertion and withdrawal cycles This sec

16、tion is not applicable to this CID. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55Lb2 Dash nuniber (see table I) AA55 162 - 01-s O1 -D O1 -E 02-s 02-D 02-E 9999974 OLbL05 Ob7 Vendor comercial PIN CAGE 00779 821 829- 2 821893- 2 821831 -2 82

17、 1828- 2 821885 - 2 821 830- 2 a -. A- A- 55 162 5.2 Contractor certification. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of this CID and that the product conforms to the producers own drawings, specifications, standards, qual

18、ity assurance practices, and is the same as the product provided as a bid sample. The procurement activity reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 5.3 Certificate of cmli

19、ance. subnit a DESC certificate of compliance to DESC-ELDI. product meets all the requirement of this CID. connectors supplied to this CID. 6. Packaging. 6.1 Preservation, packaging. wckinq. labeling. and marking. Preservation, packaging, labeling, and marking shall be as specified in the contract o

20、r purchase order. 7. NOTES. 7.1 fi. for PIN format. 7.2 Source of docunents. Each contractor desiring to be listed as a suggested source of supply shall In addition, a certificate of compliance shall accompany all This certificate shall state that the contractors The PIN should be used for governmen

21、t purposes to buy cmrcial products to this CID. See 2.1 Other Publications Joint Electron Devices Engineering Council (Application for copies should be addressed to the JEDEC Solid State Products Engineering Council, 2001 Pennsylvania Avenue, N.U., Washington, D.C. 20006). (Industry association spec

22、ifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 7.3 Government users. To acquire information on obtaining these connectors from the Govermnt inventory system, contact Defense Electronics Supp

23、ly Center, ATTN: DESC-EON, 1507 Vi Lmington Pike, Dayton, OH 45444-5522, or telephone (513) 296-5009. 7.4 ORDERING DATA. lhe contract or purchase order shall specify the following: a. CID number, revision and CID PIN. b. uality assurance provisions. c. Packaging requirements. 7.5 Sussested sources o

24、f suwly. A suggested source of supply is listed herein. Additional sources will be added as they become available. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55Lb2 m 9999974 OLb8LOb TT3 m Vendor CAGE mmber 00779 A-A-55162 Vendor name and address AMP Incorporated E i senhower Bou1 evard Harrisburg, PA 17105 CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Preparing Activity: DLA-ES Project 5935-3941-01 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-