DLA A A 59789 18A-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 250 X 290 INCH (6 35 x 7 37 mm) BODY SIZE WITH CAPTIVE REAR WEDGE AND VISUAL LOCK .pdf

《DLA A A 59789 18A-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 250 X 290 INCH (6 35 x 7 37 mm) BODY SIZE WITH CAPTIVE REAR WEDGE AND VISUAL LOCK .pdf》由会员分享，可在线阅读，更多相关《DLA A A 59789 18A-2012 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 250 X 290 INCH (6 35 x 7 37 mm) BODY SIZE WITH CAPTIVE REAR WEDGE AND VISUAL LOCK .pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA59789/18A 18 July 2012 SUPERSEDING AA59789/18 8 August 2008 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .250 X .290 INCH (6.35 x 7.37 mm) BODY SIZE, WITH CAPTIVE REAR WEDGE AND VISUAL LOCK INDICATION, SCR

2、EW ACTUATED The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATI

3、ON/PART IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see notes). AA59789 CID number /18 Applicable CID sheet * Configuration (see table I) * Finish * * Length (see

4、table II) * Mounting Example: AA59789/18DE40T is the PIN for an electroless nickel finished, 3.8 inch (96.5 mm) long card holder. The card holder also features three tapped mounting holes for use with 080 UNF 2B fasteners and a screw selflocking element for added resistance to loosening. SALIENT CHA

5、RACTERISTICS. Performance. Card holders shall hold the circuit card assembly it is attached to firmly in its installed position and prevent loosening or movement as a result of shock and vibration. The card holder shall also provide a thermal transfer path from the circuit card assembly to the cold

6、plate or heat sink surfaces. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specified in CID AA59789. Card holders shall have a visual indicator to show when the assembly is in its relaxed (u

7、nlocked) and expanded (locked) state. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “M“, “R“, “S“, “T“, and “

8、U“. Cold plate slot width. The recommended cold plate slot width to accommodate the circuit card assembly with attached card holder is .325 inch (8.25 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). AMSC N/A FSC 5998Provided by IHSNot for ResaleNo reproduction

9、 or networking permitted without license from IHS-,-,-AA59789/18A 2 Inches mm Inches mm Inches mm Inches Mm .227 .23 5.77 5.84 .250 .293 6.35 7.44 .350 .35 8.89 8.9 .80 20.32 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specif

10、ied, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. Tolerance for the hole spacing is .005 inch (0.13 mm). 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm). FIGURE 1. Relaxed and expanded dimensions. Instal

11、lation torque. The recommended nominal installation torque is follows: 6 inch-pounds (0.7 N-m) for card holders of configuration “C“ or “E“ and 7 to 8 inch-pounds (0.8 to 0.9 N-m) for assemblies of configurations “L“ or “D“. Configuration. The configuration of a card holder shall be as specified in

12、table I. The details of a particular configuration consist of those on figures 1 and 2, and may include those on figures 3 and 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/18A 3 TABLE I. Configuration. Configuration Applicable figures H

13、ardware options C 1 and 2 No added options L 1, 2 and 3 Screw self-locking element E 1, 2 and 4 Additional mounting hole D 1, 2, 3 and 4 Screw self-locking element and additional mounting hole Visual lock indicator (see figure 2). Card holders shall have a visual indicator to show when the card hold

14、er is in its relaxed (unlocked) state. When the card holder is in the unlocked (relaxed) state, the end of the actuating screw shall display a red band on the side of the screw. When the actuating screw on the card holder has been tightened (assembly expanded) so that the assembly is in the locked p

15、osition, this red band shall be concealed. FIGURE 2. Visual lock indicator. Finish. The wedge body finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “E“ (electroless nickel), “H“ (hard black anodize), or “

16、R“ (clear chemical film). Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. TABLE II. Addi

17、tional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “length“ .02 (0.5 mm) Dimension “M“ .01 (0.3 mm) Dimension “M/2“ .02 (0.5 mm) 30 2.80 (71.1) .90 (22.9) .45 (11.4) 40 3.80 (96.5) 1.90 (48.3) .95 (24.1) 50 4.80 (121.9) 2.90 (73.7) 1.45 (36.8) 1/ Dimensions are in inches.

18、Millimeters, in parenthesis, are given for general information only. Mounting. The mounting designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “M“ (tapped metric M2.5 x 0.45 holes), “R“ (rivet mount holes with counterbore and

19、 countersink), “S“ (tapped 2-56 holes), “T“ (tapped 0-80 holes), or “U“ (tapped metric M2 x 0.4 holes). See figure 1 and table II for mounting hole spacing requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/18A 4 Rivet mounting hol

20、es. The holes used for rivet mounting shall be .068/.073 inch (1.73/1.85 mm) diameter, countersunk 100 degrees by .060 inch (1.52 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59789 when rivet mounting is used. Configuration hardware options. Card holders can have the follow

21、ing options: no added hardware, screw self-locking element (see figure 2), an additional mounting hole (see figure 3), or a combination of both screw self-locking element and third mounting. See table I for the correct PIN configuration identifier for the hardware option needed. Card holders requiri

22、ng no added hardware options shall include configuration identifier “C“ in the PIN (see classification and notes section herein). Screw self-locking element (see figure 3). The use of a screw self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of

23、the card holder assembly from shock and vibration. The screw self-locking element shall be as specified in AA59789. Card holders requiring a screw self-locking element shall include configuration identifier “L“ in the PIN (see table I, classification and notes section herein). FIGURE 3. Screw self-l

24、ocking element details. Additional mounting hole (see figure 4). Card holders requiring an additional mounting hole shall include configuration identifier “E“ in the PIN (see table I, classification and notes section herein). FIGURE 4. Additional mounting hole details. Screw self-locking element and

25、 additionalmounting hole. Card holders requiring a screw self-locking element and an additional mounting hole options shall include configuration identifier “D“ in the PIN (see table I, classification and notes section herein). NOTES. PIN. The PIN should be used for Government purposes to buy commer

26、cial products to this CID specification sheet. See the classification section for PIN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/18A 5 Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedg

27、e Retainers, 5 Piece, For Cold Plate Applications, General Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Or

28、dering data. Ordering data shall be as specified in AA59789. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordinat

29、ion, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAG

30、E Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 E-mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Oranget

31、horpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. This CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designa

32、tor “50“. See table IV for CID PIN construction using other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

33、nse from IHS-,-,-AA59789/18A 6 TABLE III. Commercial part number supersession data. PIN designator AA59789/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 CB50M VA2634.80TM2.5 5263VBA4.80TM2.5 CB50R VA2634.80H 5263VBA4.80H CB50S VA2634.80T2 5263VBA4.80T2 CB50T VA2634.80T

34、0 5263VBA4.80T0 CB50U VA2634.80TM2 5263VBA4.80TM2 LB50M VA2634.80TM2.5L 5263VBA4.80TM2.5L LB50R VA2634.80HL 5263VBA4.80HL LB50S VA2634.80T2L 5263VBA4.80T2L LB50T VA2634.80T0L 5263VBA4.80T0L LB50U VA2634.80TM2L 5263VBA4.80TM2L EB50M VA2634.80ETM2.5 5263VBA4.80ETM2.5 EB50R VA2634.80EH 5263VBA4.80EH EB

35、50S VA2634.80ET2 5263VBA4.80ET2 EB50T VA2634.80ET0 5263VBA4.80ET0 EB50U VA2634.80ETM2 5263VBA4.80ETM2 DB50M VA2634.80ETM2.5L 5263VBA4.80ETM2.5L DB50R VA2634.80EHL 5263VBA4.80EHL DB50S VA2634.80ET2L 5263VBA4.80ET2L DB50T VA2634.80ET0L 5263VBA4.80ET0L DB50U VA2634.80ETM2L 5263VBA4.80ETM2L CE50M VEN263

36、4.80TM2.5 5263VEN4.80TM2.5 CE50R VEN2634.80H 5263VEN4.80H CE50S VEN2634.80T2 5263VEN4.80T2 CE50T VEN2634.80T0 5263VEN4.80T0 CE50U VEN2634.80TM2 5263VEN4.80TM2 LE50M VEN2634.80TM2.5L 5263VEN4.80TM2.5L LE50R VEN2634.80HL 5263VEN4.80HL LE50S VEN2634.80T2L 5263VEN4.80T2L LE50T VEN2634.80T0L 5263VEN4.80T

37、0L LE50U VEN2634.80TM2L 5263VEN4.80TM2L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/18A 7 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/18 Vendor similar designator or

38、type part number 1/ 2/ CAGE 61081 CAGE 5BG68 EE50M VEN2634.80ETM2.5 5263VEN4.80ETM2.5 EE50R VEN2634.80EH 5263VEN4.80EH EE50S VEN2634.80ET2 5263VEN4.80ET2 EE50T VEN2634.80ET0 5263VEN4.80ET0 EE50U VEN2634.80ETM2 5263VEN4.80ETM2 DE50M VEN2634.80ETM2.5L 5263VEN4.80ETM2.5L DE50R VEN2634.80EHL 5263VEN4.80

39、EHL DE50S VEN2634.80ET2L 5263VEN4.80ET2L DE50T VEN2634.80ET0L 5263VEN4.80ET0L DE50U VEN2634.80ETM2L 5263VEN4.80ETM2L CH50M VHA2634.80TM2.5 5263VBH4.80TM2.5 CH50R VHA2634.80H 5263VBH4.80H CH50S VHA2634.80T2 5263VBH4.80T2 CH50T VHA2634.80T0 5263VBH4.80T0 CH50U VHA2634.80TM2 5263VBH4.80TM2 LH50M VHA263

40、4.80TM2.5L 5263VBH4.80T2.5L LH50R VHA2634.80HL 5263VBH4.80HL LH50S VHA2634.80T2L 5263VBH4.80T2L LH50T VHA2634.80T0L 5263VBH4.80T0L LH50U VHA2634.80TM2L 5263VBH4.80TM2L EH50M VHA2634.80ETM2.5 5263VBH4.80ETM2.5 EH50R VHA2634.80EH 5263VBH4.80EH EH50S VHA2634.80ET2 5263BH4.80ET2 EH50T VHA2634.80ET0 5263

41、VBH4.80ET0 EH50U VHA2634.80ETM2 5263VBH4.80ETM2 DH50M VHA2634.80ETM2.5L 5263VBH4.80ET2.5L DH50R VHA2634.80EHL 5263VBH4.80EHL DH50S VHA2634.80ET2L 5263VBH4.80ET2L DH50T VHA2634.80ET0L 5263VBH4.80ET0L DH50U VHA2634.80ETM2L 5263VBH4.80ETM2L See footnote at end of table. Provided by IHSNot for ResaleNo

42、reproduction or networking permitted without license from IHS-,-,-AA59789/18A 8 TABLE III. Commercial part number supersession data Continued. PIN designator AA59789/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 CR50M VR2634.80TM2.5 5263VCC4.80TM2.5 CR50R VR2634.80H 52

43、63VCC4.80H CR50S VR2634.80T2 5263VCC4.80T2 CR50T VR2634.80T0 5263VCC4.80T0 CR50U VR2634.80TM2 5263VCC4.80TM2 LR50M VR2634.80TM2.5L 5263VCC4.80T2.5L LR50R VR2634.80HL 5263VCC4.80HL LR50S VR2634.80T2L 5263VCC4.80T2L LR50T VR2634.80T0L 5263VCC4.80T0L LR50U VR2634.80TM2L 5263VCC4.80TM2L ER50M R2634.80ET

44、M2.5 5263VCC4.80ETM2.5 ER50R R2634.80EH 5263VCC4.80EH ER50S R2634.80ET2 5263VCC4.80ET2 ER50T R2634.80ET0 5263VCC4.80ET0 ER50U R2634.80ETM2 5263VCC4.80ETM2 DR50M R2634.80ETM2.5L 5263VCC4.80ET2.5L DR50R R2634.80EHL 5263VCC4.80EHL DR50S R2634.80ET2L 5263VCC4.80ET2L DR50T R2634.80ET0L 5263VCC4.80ET0L DR

45、50U R2634.80ETM2L 5263VCC4.80ETM2L 1/ The CID PINs listed are only for length designator “50“. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commer

46、cial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/18A 9 TABLE IV. Example of PIN with available

47、length designators. PIN designator AA59789/18 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 DE30T VEN2632.80ET0L 5263VEN2.80ET0L DE40T VEN2633.80ET0L 5263VEN3.80ET0L DE50T VEN2634.80ET0L 5263VEN4.80ET0L 1/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking pa