DLA A A 55563 5C B-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES.pdf

《DLA A A 55563 5C B-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES.pdf》由会员分享，可在线阅读，更多相关《DLA A A 55563 5C B-2011 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITH FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA55563/5C 5 December 2011 Superseding AA55563/5B 16 May 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES The General Services Administration has authorized the us

2、e of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item descript

3、ion (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /05 Applicable CID specification sheet Material # Card holder width/ board thickness (see table I) $ Length (see tabl

4、e II) AA55563/05#$ AA55563/05#$ base material is beryllium copper 1/4 hard; card holder width/board thickness, dimension “D“, is .33 inch (8.38 mm), dimension “T“ is .0937 inch (2.29 mm), commonly known as having a board thickness of “3/32” the overall length is 2.0 inches (50.80 mm), dimension “L“;

5、 and the finish is black ebonal. 2/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PINs shown. For actual part m

6、arking requirements, see the marking paragraph of of AA55563. 3/ Finish materials designator “C“, “D“, “E“, “F“, “H“, “J“, “K“, or “R“ are available for this material type (see finish for a description of the designators). 4/ MFG CAGE 18915 the series type is “35-7F“, the letters “B“, “BH“, or “CR“

7、denotes material type, the letter “T“ denotes card holder width/board thickness, the numbers “4“ through “15“ denotes card holder lengths, and the letter “F“ denotes finish material. 5/ MFG CAGE 65884 catalog PINs are the same as this CID sheet. The character “#“ denotes the card holder width/board

8、thickness and needs to be replaced with the appropriate PIN designator from table I. The character “&“ finish material and shall be replaced with the appropriate PIN designator (see finish). See 1/ above. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

9、-,-AA55563/5C 7 Guidance on use of alternative parts with less hazardous or nonhazardous materials. This CID specification sheet provides for a number of alternative plating materials via the PIN. Users should select the PIN with the least hazardous material that meets the form, fit, and function re

10、quirements of their application. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS: Army CR Navy EC Preparing Activity: Air Force 85 DLA CC DLA CC Review Activity: Project: 59982011015 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-