DIN ISO 702-3-2010 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Part 3 Bayonet type (ISO 702-3 2007)《机床 主轴端部和工件夹盘的连接尺寸 第3部分 卡口型》.pdf

《DIN ISO 702-3-2010 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Part 3 Bayonet type (ISO 702-3 2007)《机床 主轴端部和工件夹盘的连接尺寸 第3部分 卡口型》.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 702-3-2010 Machine tools - Connecting dimensions of spindle noses and work holding chucks - Part 3 Bayonet type (ISO 702-3 2007)《机床 主轴端部和工件夹盘的连接尺寸 第3部分 卡口型》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、April 2010 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、5.060.20!$aAx“1623085www.din.deDDIN ISO 702-3Machine tools Connecting dimensions of spindle noses and work holding chucks Part 3: Bayonet type (ISO 702-3:2007)English translation of DIN ISO 702-3:2010-04Werkzeugmaschinen Spindelkpfe und Drehfutter, Anschlussmae Teil 3: Kurzkegelaufnahme mit Bajonett

3、-Befestigung (ISO 702-3:2007)Englische bersetzung von DIN ISO 702-3:2010-04Machines-outils Dimensions dassemblage des nez de broches et des mandrins porte-pices Partie 3: Type baonnette (ISO 702-3:2007)Traduction anglaise de DIN ISO 702-3:2010-04supersedesDIN 55028:1980-03;supersedesDIN 55027:1980-0

4、3www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 13 pagesDIN ISO 702-1:2010-04,Together with03.10 A comma is used as the decimal marker. Contents Page National foreword 2 1 Scope 4 2 Interchangeability 4 3 Sizes for interchangeability5

5、3.1 Spindle noses.5 3.2 Bayonet disc.7 3.3 Face plates .9 3.4 Studs with nuts and collars. 11 Bibliography. 13 National foreword This standard has been prepared by Technical Committee ISO/TC 39 “Machine tools”, Subcommittee SC 8 “Work holding spindles and chucks”. The responsible German body involve

6、d in its preparation was the Normenausschuss Werkzeuge und Spannzeuge (Tools and Clamping Devices Standards Committee), Working Committee NA 121-02-07 AA Drehmaschinenspannzeuge und Zubehr. Following a proposal of the German Working Committee, ISO 702-1 has been editorially harmonized with ISO 702-2

7、, ISO 702-3 and ISO 702-4. All four ISO Standards have been adopted as DIN ISO Standards and published as a series. This second edition cancels and replaces the first edition (ISO 702-3:1975), which has been technically revised. DIN ISO 702 consists of the following parts, under the general title Ma

8、chine tools Connecting dimensions of spindle noses and work holding chucks: Part 1: Conical connection Part 2: Camlock type Part 3: Bayonet type Part 4: Cylindrical connection DIN ISO 702-3 supersedes DIN 55027 and, together with DIN ISO 702-1, supersedes DIN 55028. Spindle nose types A, B and C pre

9、viously specified in DIN 55028 have been replaced and are now dealt with in DIN ISO 702-1 (types A and B) and DIN ISO 702-3 (type C). With the publication of the DIN ISO 702 series of standards, DIN 55026, DIN 55027, DIN 55028 and DIN 55029 have been withdrawn. Attention is drawn to the possibility

10、that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. 2 DIN ISO 702-3:2010-04 Amendments This standard differs from DIN 55027:1980-03 and DIN 55028:1980-03 as follows: a) The standard has been

11、completely revised and brought into line with the current state of technology. b) Drawings and dimensioning have been revised and brought into line with the current rules of presentation. c) The tables have been revised accordingly. d) The type C spindle nose from DIN 55028 has been replaced. Previo

12、us editions DIN 55027: 1980-03 DIN 55028: 1980-03 3 DIN ISO 702-3:2010-04 1 Scope This part of ISO 702 specifies the sizes for interchangeability of bayonet-type lathe spindle noses and corresponding face plates. NOTE The “conical connection”, “camlock type” and “cylindrical connection” are dealt wi

13、th in ISO 702-1, ISO 702-2 and ISO 702-4, respectively. 2 Interchangeability In this part of ISO 702, all the dimensions and tolerances are expressed in millimetres. Machine tools Connecting dimensions of spindle noses and work holding chucks Part 3: Bayonet type 4 DIN ISO 702-3:2010-04 3 Sizes for

14、interchangeability 3.1 Spindle noses Key 1 size Nos. 3 and 4, No. 3 without button 2 size Nos. 5 to 8 3 size Nos. 11 to 20 aAll holes. Figure 1 Spindle noses 5 DIN ISO 702-3:2010-04 Table 1 Dimensions of spindle noses Size No. Dimension 3 4 5 6 8 11 15 20 nom. 53,975 63,513 82,563 106,375 139,719 19

15、6,869 285,775 412,775 d1 tol. +0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,020 0 d275 85 104,8 133,4 171,4 235 330,2 463,6 d3102 112 135 170 220 290 400 540 d421 21 21 23 29 36 43 43 d5 H8/h8 14,25 15,9 19,05 23,8 28,6 34,9 41,3 d66,4 6,4 6,4 8,4 10,5 10,5 13 13 d710,4 10,4 10,4

16、 13,5 16,5 16,5 19 19 e 11 11 13 14 16 18 19 21 f 16 20 22 25 28 35 42 48 g 5 5 5 6 8 8 8 h 10 10 10 11 12 13 15 15 w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 NOTE General tolerance for untoleranced dimensions: 0,4 mm. 6 DIN ISO 702-3:2010-04 3.2 Bayonet disc Key 1 size Nos. 3 and 4 2 size Nos. 5 to 8 3 size

17、 Nos. 11 to 20 4 thrust socket 5 hexagon-socket head screw aAll holes. Figure 2 Bayonet disc 7 DIN ISO 702-3:2010-04 Table 2 Dimensions of bayonet disc Size No. Dimension 3 4 5 6 8 11 15 20 d175 85 104,8 133,4 171,4 235 330,2 463,6 d250 60 80 100 130 185 270 400 d3110 120 145 180 230 300 410 550 d42

18、1 21 21 23 29 36 43 43 d5 M6 M6 M6 M8 M10 M10 M12 M12 d6 11 11 11 13 17 17 22 22 d716 16 16 19 25 25 32 32 e 11,5 11,5 11,5 14 18 23 27 27 f 11,5 11,5 11,5 14 18 18 23 23 g0 0,1 5 6 8 10 12 16 18 22 h 8 9 12 15 18 22 26 30 h1 +0,2 0 5,2 6,2 8,2 10,2 12,2 16,2 18,3 22,3 s 0 0,2 14 14 14 17 22 22 27 2

19、7 w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 Hexagon-socket head screw M6 15 M6 20 M6 25 M8 30 M10 35 M10 45 M12 55 M12 65 NOTE General tolerance for untoleranced dimensions: 0,4 mm. 8 DIN ISO 702-3:2010-04 3.3 Face plates Figure 3 Face plates 9 DIN ISO 702-3:2010-04 Table 3 Dimensions of face plates Size No

20、. Dimension 3 4 5 6 8 11 15 20 d1 nom. 53,975 63,513 82,563 106,375 139,719 196,869 285,775 412,775 tol. Type 1a+0,003 0,005 +0,003 0,005 +0,004 0,006 +0,004 0,006 +0,004 0,008 +0,004 0,010 +0,004 0,012 +0,005 0,015 tol. Type 2 a+0,008 0 +0,008 0 +0,010 0 +0,010 0 +0,012 0 +0,014 0 +0,016 0 +0,020 0

21、 d275 85 104,8 133,4 171,4 235 330,2 463,6 d351,5 61 79,6 103,2 136,2 192,9 281,5 408 d4102 112 135 170 220 290 400 540 d5M10 M10 M10 M12 M16 M20 M24 M24 d6 +0,1 0 14,7 16,3 19,45 24,25 29,4 35,7 42,1 d7 11 11 11 14 18 22 26 26 e 10 10 12 13 14 16 17 19 f 15 15 15 18 24 30 36 36 g 18 18 18 22 28 34

22、40 40 h 6,5 6,5 6,5 8 10 10 10 w 0,2 0,2 0,2 0,2 0,2 0,2 0,3 0,3 Stud M10 34 M10 39 M10 43 M12 50 M16 60 M20 75 M24 90 M24 100 NOTE General tolerance for untoleranced dimensions: 0,4 mm. aType identification shall be marked. 10 DIN ISO 702-3:2010-04 3.4 Studs with nuts and collars Key 1 stud 2 nut w

23、ith collars Figure 4 Stud bolt with collar nut 11 DIN ISO 702-3:2010-04 Table 4 Dimensions of studs with nuts and collars Size No. Dimension 3 4 5 6 8 11 15 20 d1M10 M10 M10 M12 M16 M20 M24 M24 d2 h11 19,5 19,5 19,5 21,5 27 34 41 41 d3 7,7 7,7 7,7 9,4 13 16,4 19,6 19,6 h112 12 12 14 18 22 27 27 h23

24、3 3 3 3 4 4 4 l134 39 43 50 60 75 90 100 l220 22 24 28 35 44 52 56 l318 18 18 20 25 30 36 36 l412 12 12 15 20 25 30 30 l55 8 10 12 12 15 20 26 r 0,6 0,6 0,6 1 1 1 1,6 1,6 s 17 17 17 19 24 30 36 36 NOTE General tolerance for untoleranced dimensions: 0,4 mm. 12 DIN ISO 702-3:2010-04 Bibliography 1 ISO

25、 702-1, Machine tools Connecting dimensions of spindle noses and work holding chucks Part 1: Conical connection 2 ISO 702-2, Machine tools Connecting dimensions of spindle noses and work holding chucks Part 2: Camlock type 3 ISO 702-4, Machine tools Connecting dimensions of spindle noses and work holding chucks Par 4: Cylindrical connection 13 DIN ISO 702-3:2010-04