DIN ISO 2380-1-2006 Assembly tools for screws and nuts - Screwdrivers for slotted-head screws - Part 1 Tips for hand- and machine-operated screwdrivers (ISO 2380-1 2004) English ve.pdf

《DIN ISO 2380-1-2006 Assembly tools for screws and nuts - Screwdrivers for slotted-head screws - Part 1 Tips for hand- and machine-operated screwdrivers (ISO 2380-1 2004) English ve.pdf》由会员分享，可在线阅读，更多相关《DIN ISO 2380-1-2006 Assembly tools for screws and nuts - Screwdrivers for slotted-head screws - Part 1 Tips for hand- and machine-operated screwdrivers (ISO 2380-1 2004) English ve.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 DEUTSCHE NORMJanuary 2006DIN ISO 2380-1 ICS 25.140.01 Supersedes: see below Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 1: Tips for hand- and machine-operated screwdrivers (ISO 2380-1:2004) English version of DIN ISO 2380-1:2006 Schraubwerkzeuge Schraubendreher fr S

2、chrauben mit Schlitz Teil 1: Spitzen fr hand- und maschinenbettigte Schraubendreher (ISO 2380-1:2004) Englische Fassung DIN ISO 2380-1:2006 Together with DIN ISO 2380-2:2006-01, supersedes DIN 5263:1991-05; together with DIN 5264:2006-01, supersedes DIN 5264:1999-07 Document comprises 9 pages No par

3、t of this standard may be reproduced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 7 www.din.de www.beuth.de !,jVO“06.06 9715144DIN ISO 2380

4、-1:2006-01 2 National foreword This standard has been prepared by ISO/TC 29 Small tools, Subcommittee SC 10 Assembly tools for screws and nuts, pliers and nippers. The responsible German body involved in its preparation was the Normenausschuss Werkzeuge und Spann-zeuge (Tools and Clamping Devices St

5、andards Committee), Technical Committee NA 121-08-01 AA Schraub-werkzeuge. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. ISO 2380 consists of the f

6、ollowing parts, under the general title Assembly tools for screws and nuts Screwdrivers for slotted-head screws: Part 1: Tips for hand- and machine-operated screwdrivers Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers The DIN Standard corresponding to the In

7、ternational Standard referred to in clause 2 of the ISO Standard is as follows: ISO 2380-2 DIN ISO 2380-2 Amendments This standard differs from DIN 5263, May 1991 edition, and DIN 5264, July 1999 edition, as follows: a) The specifications of DIN 5263:1991-05 are now covered in DIN ISO 2380-1 and DIN

8、 ISO 2380-2. b) The specifications of DIN 5264:1994-01 are now covered in DIN ISO 2380-1 and DIN 5264. Previous editions DIN 5263: 1967-07, 1973-11, 1982-10, 1991-05 DIN 5264: 1965-11, 1973-08, 1982-10, 1987-01, 1991-05, 1999-07 National Annex NA (informative) Bibliography DIN ISO 2380-2, Assembly t

9、ools for screws and nuts Screwdrivers for slotted-head screws Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers ISO 2380-1:2004 (E) 1 Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 1: Tips for hand- and machine-operated screwdrive

10、rs Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which

11、a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matt

12、ers of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circul

13、ated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsib

14、le for identifying any or all such patent rights. ISO 2380-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This third edition cancels and replaces the second edition (ISO 2380-1:1997), which has been technicall

15、y revised. ISO 2380 consists of the following parts, under the general title Assembly tools for screws and nuts Screwdrivers for slotted-head screws: Part 1: Tips for hand- and machine-operated screwdrivers Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers ISO

16、 2380-1:2004 (E) 2 1 Scope This part of ISO 2380 specifies the shape/form, dimensions and designation of the tips of hand- and machine-operated screwdrivers for slotted-head screws. It also gives the technical specifications and test conditions for the screw-drivers and, in the case of hand-operated

17、 screwdrivers, specifies the test torque which the blade-to-handle connection shall withstand. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest ed

18、ition of the referenced document (including any amendments) applies. ISO 2380-2:2004, Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers 3 Shape and dimensions of the tips 3.1 Shape The sha

19、pe of screwdriver tips is left to the choice of the manufacturer. 3.2 Dimensions Only the dimensions shown in Figures 1 and 2 and specified in Tables 1 and 2 shall be observed. ISO 2380-1:2004 (E) 3 Figure 1 Form A, for hand-operated screwdrivers only Figure 2 Form B for hand-operated screwdrivers a

20、nd form C for machine-operated screwdrivers Table 1 Hand-operated screwdriver tips, forms A and B Dimensions in millimetres Nominal thickness Nominal width Tolerances on Test torque a b a b t1aa1bt2aMminForms A and B Form A Form B min. Nm 2 0,3 0,4 2,5 0,2 0,32 0,7 0,4 0,5 3 0,3 0,4 0,9 0,7 3 00,250

21、0,141,1 0,6 3,5 0,060,02+0,4 0,48 1,1 1,3 0,8 4 0,5 0,64 1,4 2,6 4,5 4,5 1 5,5 00,300,180,6 0,8 1,8 5,5 6,5 9,4 1,2 8 0,060,04+0,7 0,96 2,2 11,5 8 20,5 1,6 10 00,3600,221 1,28 2,9 25,6 2 12 1,2 1,6 3,6 48 2,5 14 0,06 00,4300,271,5 2 4,5 87,5 at1,t2are the reference distances without tolerances.t1= 0

22、,6 a t2= 1,8 a b1a1, min= 0,8 a The profile of dimensions a1to a within the reference distances t2shall be at least equal (parallel) or continuously ascending.a a ISO 2380-1:2004 (E) 4 Table 2 Machine-operated screwdriver tips, Form C Dimensions in millimetres Nominal thickness Nominal width Toleran

23、ces on Test torque a b a b a1at2bM1, minmin. Nm 2 0,35 0,4 2,5 0,32 0,7 0,45 3 00,060,8 0,5 4 00,0750,4 0,9 1,1 3 00,061,2 3,5 1,4 0,6 4,5 0,48 1,1 1,8 4 2,9 0,8 5,5 0,64 1,4 3,9 4,5 5 5,5 6,2 1 6,0 0,040+00,0750,8 1,8 6,7 6,5 10,5 1,2 8 0,96 2,2 12,9 8 22,9 1,6 10 00,151,28 2,9 28,7 2 12 1,6 3,6 53

24、,8 2,5 14 0,03 00,182 4,5 98 aa1a a1, min= 0,8 a The profile of dimensions a1to a within the reference distances t2shall be at least equal (parallel) or continuously ascending. bt2is the reference distance without tolerance. t2= 1,8 a 4 Designation of the tips The designation of the tips shall inclu

25、de, in the following order: a) “Tip”; b) reference to this part of ISO 2380, i.e. “ISO 2380-1”; c) form; d) nominal thickness, a, in millimetres; e) nominal width, b, in millimetres. EXAMPLE A tip, form A, of nominal thickness a = 1,2 mm and of nominal width b = 8 mm is designated as follows: Tip IS

26、O 2380-1 A 1,2 8 ISO 2380-1:2004 (E) 5 5 Technical specifications and test conditions for the screwdrivers 5.1 Hardness Hand-operated screwdrivers shall have a minimum hardness of 50 HRC over at least the length 3 x b from the tip of the blade, while machine-operated screwdrivers shall have a minimu

27、m hardness of 56 HRC along their full length. 5.2 Test conditions for the blades or bits When tested with the minimum test torques M and M1, expressed in newton metres, in accordance with Tables 1 and 2, the screwdriver blades or bits shall not show any cracks or breaks or any permanent deformations

28、 which could influence their usability. NOTE The minimum test torques have been calculated using the following formulae: 2M ba= and M1= 1,12 ba2 where a is the nominal thickness of the tip, expressed in millimetres; b is the nominal width of the tip, expressed in millimetres. A torque testing device

29、 shall be used which sustains the test specimen against ejecting forces and prevents the occurrence of bending moments, and the test disc used shall be according to Figure 3 or Figure 4, have a hardness of at least 64 HRC and be of such strength that no deformation can occur during testing. The test

30、 disc values a, t1and t2are according to Table 3. Dimensions in millimetres Figure 3 Test disc for form A ISO 2380-1:2004 (E) 6 Dimensions in millimetres Figure 4 Test disc for forms B and C Table 3 Test disc values Dimensions in millimetres a t1 t20,0850,060+0,0400+0,1400+0,4 0,2 0,7 0,5 0,3 0,9 0,

31、6 0,4 1,1 0,8 0,5 1,4 1 0,6 1,8 1,2 0,7 2,2 1,6 1 2,9 2 1,2 3,6 2,5 1,5 4,5 5.3 Test torque of the blade-to-handle connection (hand-operated screwdrivers) The test torque which the blade-to-handle connection shall withstand is related to the test torque of the blade as given in Table 4. Table 4 Test

32、 torque Test torque of blade Test torque of blade-to-handle connection M M Nm Nm M M M M 26 M 30 The application of the test equipment to the handle should not modify the characteristics of the connection to be tested. 26 ISO 2380-1:2004 (E) 7 When there is a hexagonal drive, as shown in ISO 2380-2:2004, Figure 2, the connection hexagon to screwdriver blade shall withstand a test torque of M 1,5. For a screwdriver with a handle, the blade-to-handle connection shall be such that no relative torsion of blade to handle occurs when subjected to a test torque M limited to 30 Nm.