DIN EN ISO 8092-1-1998 Road vehicles - Connections for on-board electrical wiring harnesses - Part 1 Tabs for single-pole connections - Dimensions and specific requirements (ISO 80.pdf

《DIN EN ISO 8092-1-1998 Road vehicles - Connections for on-board electrical wiring harnesses - Part 1 Tabs for single-pole connections - Dimensions and specific requirements (ISO 80.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 8092-1-1998 Road vehicles - Connections for on-board electrical wiring harnesses - Part 1 Tabs for single-pole connections - Dimensions and specific requirements (ISO 80.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Road vehicles - Connections for on-board electrical wiring harnesses Part 1 : Tabs for single-pole connections - Dimensions and specific requirements (IS0 8092-1 : 1996) English version of DIN EN IS0 8092-1 Straenfahrzeuge - Steckverbindungen fr das elektrische Fahrzeug- Bordnetz - Teil 1 : Flachste

2、cker fr einpolige Steckverbindungen - Mae und besondere Anforderungen (IS0 8092-1 : 1996) DIN - EN IS0 8092-1 European Standard EN IS0 8092-1 : 1998 has the status of a DIN Standard. National Annex NA Standard referred to (and not included in Normative references and Annex ZA) DIN EN IS0 8092-2 Road

3、 vehicles - Connections for on-board electrical wiring harnesses - Part 2: Defini- I tions, test methods and general performance requirements (IS0 8092-2 : 1996) A comma is used as the decimal marker. National foreword This standard has been published in accordance with a decision taken by CEN/CS to

4、 adopt, without alteration, International Standard IS0 8092-1 as a European Standard. The responsible German body involved in its preparation was the Normenausschu Kraftfahrzeuge (Road Vehicle Standards Committee). DIN EN IS0 8092-2 is the standard corresponding to International Standard IS0 8092-2

5、referred to in clause 2 of the EN. Amendments DIN EN 28092-1, January 1992 edition, has been superseded by the specifications of EN IS0 8092-1. Previous edition DIN EN 28092-1: 1992-01. EN comprises 7 pages. Q No part of this standard may be reproduced without the prior permission of Ref. No. DIN EN

6、 IS0 8092-1 : 1998-1 O DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen). English price group O7 Sales No. 1107 04.99 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 8092-1 August 1998 ICs 43

7、.040.1 O Descriptors: Road vehicles, electrical wiring harnesses, connections, Supersedes EN 28092-1 : 1991. tabs, requirements. English version Road vehicles - Connections for on-board electrical wiring harnesses Part 1 : Tabs for single-pole connections - Dimensions and specific requirements (IS0

8、8092-1 : 1996) Vhicules routiers - Connexions pour faisceaux de cblage lectrique embarqus - Partie 1 : Languettes pour raccordements unipolaires - Dimensions et exigences particulires Straenfahrzeuge - Steckverbindun- gen fr das elektrische Fahrzeug- Bordnetz - Teil 1 : Flachstecker fr einpolige Ste

9、ckverbindungen - Mae und besondere Anforderungen (IS0 8092-1 : 1996) (IS0 8092-1 : 1996) This European Standard was approved by CEN on 1998-07-26. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

10、 national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version

11、 in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, Fra

12、nce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 B

13、russels O 1998. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN IS0 8092-1 : 1998 E Page 2 EN IS0 8092-1 : 1998 Foreword International Standard IS0 8092-1 : 1996 Road vehicles - Connections for on-board electrical wiring harnesse

14、s - Part 1 : Tabs for single-pole connections - Dimensions and specific requirements, which was prepared by ISO/TC 22 Road vehicles of the International Organization for Standardization, has been adopted by CEN/CS as a European Standard. This European Standard shall be given the status of a national

15、 standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by February 1999 at the latest. In accordance with the CENKENELEC Internal Regulations, the national standards organizations of the follow- ing countries are bound to implement this

16、 European Standard: Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Endorsement notice The text of the International Standard IS0 8092-1 : 1996

17、 was approved by CEN as a European Standard without any modification. NOTE: Normative references to international publications are listed in Annex ZA (normative). 1 Scope This part of IS0 8092 specifies dimensions for the tabs of single-pole connections and specific require- ments, for on-board elec

18、trical wiring harnesses of road vehicles, which can be fitted into female con- tacts such as those given in annex A. It applies to connectors designed to be disconnected after mounting in the vehicle for the purposes of repair and/or maintenance only. 2 Normative reference The following standard con

19、tains provisions which, through reference in this text, constitute provisions of this part of IS0 8092. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this part of IS0 8092 are encouraged to investigate the possi

20、bility of applying the most recent edition of the standard indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 8092-2:1996, Road vehicles - Connections for on-board electrical wiring harnesses - Part 2: Defi- nitions, rest methods and general pe

21、rformance re- quirements. 3 Definitions For the purposes of this part of IS0 8092, the defi- nitions given in IS0 8092-2 apply. 4 Dimensions Tabs for single-pole connections shall conform to the dimensions given in table 1 and figure 1. Details not specified are left to the manufacturers choice . 5

22、Specific Performance requirements Single-pole connections shall be in conformity with the general performance requirements of IS0 8092-2, and shall meet the following specific requirements. 5.1 Design requirements A tab without detent requires external means of re- tention to the mating part. If tab

23、s are stamped or stamped and formed, the usable contact area shall be specified and care shall be taken to assure that gaps, seams and rounded edges do not affect the contact performance. 5.2 Connection forces and disconnection forces Connectors for single-pole connections, tested in ac- cordance wi

24、th IS0 8092-2:1995, subclause 4.3 shall meet the requirements in table 2. Page 3 EN IS0 8092-1 : 1998 r X Ln -9 N - 1 cz -x bi -* I /i I a) Tab without shoulder b) Tab with shoulder a I 1) Bevel 1, x 45 need not be a straight Line but shall not be a concave curve if it is within the confines shown:

25、it may be a radius of 1,. 2) Tabs with one shoulder are optional. 3) (functional area of tab). Retention features of the tab shall not be within this length (see 5.1). is the tab length required for engaging the female contact ./A rj c1 Figure 1 - Tab dimensions for tabs with detent - Page 4 EN IS0

26、8092-1 : 1998 Dimension Table 1 - Tab dimensions Dimensions in millimetres Size) 2,8 x 0.5 I 2Bx0.8 I 4.8 x 0.5 I 4.80.8 I 63 x 0,8 I 9.5 x 1.2 1, min. max min. max. 12 3 min. 8.1 a 10.1 14,5 0.6 0.9 1 ,o 1.3 0.3 0.6 0,s 0.7 7.3 6.5 8,1 12.5 7.0 6,2 7.8 12,o rnax. min. 1.8 3,4 4,7 5.5 1,3 3.0 4,O 4.

27、5 max min h, max min b2 max min Cl 0.2 2.9 4.9 6.4 9,6 2,7 4.7 62 9,4 23 3.5 4.7 6.5 2.0 3.0 3.7 5.5 0,54 0,84 0.54 0,84 0.84 1.23 0.47 0.77 0.47 0.77 0,77 1.17 max. I c2 min. 0.07 0.3 O. 5 0.3 O. 5 0,s O. 7 o. 1 0.3 o. 1 0,3 0.3 O, 5 O. 06 I I 1 -1 max. D2 min. I First disconnection force max. I 27

28、 I 53 I 30 I 67 I 45 I 80 I 100 I 13 1,s 2 1,1 1.3 1,6 1.7 I 10th disconnection force min.1 4 I 6 I 7 I15 I 9 I18 I30 I Connection and disconnection First connection force rnax. 1 ) P refers to positive locking female contact. 2) F refers to female contact without positive locking. I Force, N Tab si

29、ze 23 4.8 63 9-5 P) F*) P F P F F 27 53 30 67 45 80 I O0 Page 5 EN IS0 8092-1 : 1998 6 Designation Tabs in accordance with this part of IS0 8092 shall be designated as follows. EXAMPLE Initial ma 5.3 Connection resistance After endurance 1) 1) YO of initial measured value ma Single-pole connections,

30、 tested in accordance with IS0 8092-2:1995, subclause 4.8, shall meet the re- quirements in table 3. Table 3 - Maximum permitted connection resistance Connection resistance mgX. I 1;. I y;. 1 1 i As selected by supplier and user. International Standard number Tab size Tab type First digit: 1 = tab w

31、ith one shoulder 2 = tab with two shoulders O = tab without shoulder Second digit: H = tab with detent N = tab without detent Page 6 EN IS0 8092-1 : 1998 1 2 6.3 Annex A (informative) 7.8 3.2 7.7 8.9 4.2 7.2 Examples of single-pole female contacts 1 2 9,5 This annex shows examples in figureA.l of si

32、ngle-pole female contact designs and reference dimensions in tableA.l. All other designs that meet the performance requirements specified in IS0 8092-2 are acceptable. 12 3.8 11 - - - t- 1, i 1-1 I -i Figure A.l - Typical forms Table A.l - Dimensions Dimensions in millimetres Page 7 EN IS0 8092-1 :

33、1998 Annex ZA (nonnative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and

34、 the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Yearm - EN Year IS0 8092-2 1996 Road vehicles - Flat, quick-connect EN IS0 8092-2 1998 terminations - Part 2: Test and performance requirements for single pole connections