DIN EN ISO 3582-2007 Flexible cellular polymeric materials - nLaboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame (ISO 3582 20.pdf

《DIN EN ISO 3582-2007 Flexible cellular polymeric materials - nLaboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame (ISO 3582 20.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 3582-2007 Flexible cellular polymeric materials - nLaboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame (ISO 3582 20.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、December 2007DEUTSCHE NORM English price group 10No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.100!$JG“1398836www

2、.din.deDDIN EN ISO 3582SupersedesDIN EN ISO 3582:2001-03www.beuth.deFlexible cellular polymeric materials Laboratory assessment of horizontal burning characteristics of small (includes Amendment A1:2007) English version of DIN EN ISO 3582:2007-12 Weich-elastische, polymere Schaumstoffe Laboratoriums

3、verfahren zur Bestimmung des horizontalen Brennverhaltens kleiner (enthlt nderung A1:2007) Englische Fassung DIN EN ISO 3582:2007-12 Document comprises 15 pagesspecimens subjected to a small flame (ISO 3582:2000+Amd. 1:2007) Probekrper bei Einwirkung einer kleinen Flamme (ISO 3582:2000+Amd. 1:2007)

4、DIN EN ISO 3582:2007-12 2 National foreword This standard has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” Subcommittee SC 4 “Products (other than hoses)” in collaboration with Technical Committee CEN/TC 249 “Plastics” (Secretariat: NBN, Belgium). The responsible Germa

5、n body involved in its preparation was the Normenausschuss Materialprfung (Materials Testing Standards Committee), Technical Committee NA 062-04-37 AA Prfung weich-elastischer Schaumstoffe. This document includes Amendment 1, approved by CEN on 2007-08-08. The start and finish of text introduced or

6、altered by amendment is indicated in the text by a vertical line in the left margin. Amendments This standard differs from DIN EN ISO 3582:2001-03 as follows: a) Clause 2 “Normative references” has been revised. b) Clause 7 “Conditioning of test pieces” has been extended. Previous editions DIN EN IS

7、O 3582: 2001-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3582 December 2000 +A1 September 2007 ICS 83.100; 13.220.40 English version Flexible cellular polymeric materials Laboratory assessment of horizontal burning characteristics of small specimens subjected to a small flame (ISO 35

8、82:2000+Amd. 1:2007) Matires alvolaires polymres souples Mthode de laboratoire pour la dtermination des caractristiques de combustion de petites prouvettes soumises, en position horizontale, une petite flamme (ISO 3582:2000+Amd. 1:2007) Weich-elastische, polymere Schaumstoffe Laboratoriumsverfahren

9、zur Bestimmung des horizontalen Brennverhaltens kleiner Probekrper bei Einwirkung einer kleinen Flamme (ISO 3582:2000+Amd. 1:2007) EN ISO 3582:2000 was approved by CEN on 2000-12-09 and Amendment A1 on 2007-08-08. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipul

10、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. The European Standards exist

11、 in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies

12、of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, and United Kingdom. EUROP

13、EAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3582:2000+A1:2007 EEN ISO 35

14、82:2000+A1:2007 (E) 2 Contents Page Foreword to EN ISO 3582:20003 Foreword to EN ISO 3582:2000/A1:2007.3 1 Scope 4 2 Normative reference 4 3 Significance of test4 4 General5 5 Apparatus .5 6 Number, size, marking and weighing of test pieces 9 7 Conditioning of test pieces.9 8 Test procedure.10 9 Cal

15、culations11 10 Test report 12 Annex ZA (normative) Normative references to international publications with their relevant European publications 13 EN ISO 3582:2000+A1:2007 (E) 3 Foreword to EN ISO 3582:2000 The text of the International Standard ISO 3582:2000 has been prepared by Technical Committee

16、 ISO/TC 45 “Rubber and rubber products” in collaboration with Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Ju

17、ne 2001, and conflicting national standards shall be withdrawn at the latest by June 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finl

18、and, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 3582:2000 was approved by CEN as a European Standard without any modification. NOTE: Norm

19、ative references to International Standards are listed in Annex ZA (normative). Foreword to EN ISO 3582:2000/A1:2007 This document (EN ISO 3582:2000/A1:2007) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” in collaboration with Technical Committee CEN/TC 249 “Plastics

20、”, the secretariat of which is held by NBN. This Amendment to the European Standard EN ISO 3582:2000 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2008, and conflicting national standards shall be withdrawn at t

21、he latest by March 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,

22、Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 3582:2000/Amd. 1:2007 has been approved by CEN as a EN ISO 3582:2000/A1:2007 without an

23、y modification. EN ISO 3582:2000+A1:2007 (E) 4 WARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establis

24、h appropriate safety and health practices and to ensure compliance with any national regulatory conditions. 1 Scope This International Standard specifies a small-scale laboratory screening procedure for comparing the relative horizontal burning characteristics of small test pieces of flexible cellul

25、ar polymeric material exposed to a low-energy source of heat. It is intended only for the purpose of assessing quickly and simply the horizontal burning characteristics of small test pieces of the material as such, i.e. considered without reference to the environmental conditions under which the mat

26、erial, or products made from it, may be used. As a consequence, it is not possible to establish a correlation between the results of this test and the performance of such materials or products under actual service conditions. The test is restricted to test pieces of thickness greater than 5 mm. Resu

27、lts of tests on test pieces of different thicknesses are not comparable. This test method is not intended to be used to assess the potential fire hazard in use. NOTE For cellular plastics having a density less than 250 kg/m3, another test method exists: ISO 9772:2001, Cellular plastics Determination

28、 of horizontal burning characteristics of small specimens subjected to a small flame. The test equipment and procedures differ from those contained in this International Standard, and it should not therefore be assumed that they will produce identical test results. 2 Normative reference The followin

29、g normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International St

30、andard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Sta

31、ndards. ISO 1923, Cellular plastics and rubbers Determination of linear dimensions. 3 Significance of test Tests made on a material under the conditions specified here can be of considerable value in comparing the horizontal burning characteristics of different materials, in controlling manufacturin

32、g processes or in assessing any change in horizontal burning characteristics prior to, or during, use. Correlation with performance under actual service conditions is not implied, and the finished product should be tested in the form in which it will finally be used by a test method appropriate to p

33、roducts fulfilling a similar purpose. EN ISO 3582:2000+A1:2007 (E) 5 It is essential to appreciate that this method of test is not intended, and cannot be used, to assess the potential fire hazard of a material or product in use. Assessment of fire hazard would require consideration of factors such

34、as fuel contribution, intensity of burning and products of combustion, as well as environmental factors such as intensity of source, orientation of exposed material and ventilation conditions. 4 General 4.1 Horizontal burning characteristics, as measured by this test procedure, are affected by facto

35、rs such as density, any anisotropy of the cellular material and the thickness of the test piece. Certain materials may shrink from the applied flame without igniting. In this event, the test results are not valid and additional test pieces may be required to obtain the ten sets of data necessary. If

36、 the test pieces continue to shrink from the applied flame without igniting, the material is not suitable for evaluation by this method of test. 4.2 Inter-laboratory trials have shown that many variables influence the reproducibility of the results of this type of test. For this reason, the procedur

37、e laid down shall be adhered to in all respects, especially as regards the use and construction of the test chamber. 4.3 For certain materials which exhibit burning only along the upper surface of the test piece, the mass loss shall be measured and reported, if required. 4.4 The horizontal burning c

38、haracteristics of some flexible cellular polymeric materials may change with time. It is accordingly advisable to make tests before and after ageing by an appropriate procedure, details of which shall be given in the test report. 5 Apparatus 5.1 Test chamber, constructed of non-combustible materials

39、, for example insulating board on a steel frame, having inside dimensions of 600 mm 5 mm in length, 300 mm 5 mm in width and 760 mm 5 mm in height, and being otherwise as shown in Figure 1. To allow easy access between tests, the chamber may be designed so that the front panel containing the window

40、is removable, but, if so constructed, provision shall be made for ensuring that a draught-proof seal is obtained when the panel is in position. The chamber shall be used in a fume cupboard. The chamber shall be draught-free, yet permit normal thermal circulation of air past the test piece during bur

41、ning. 5.2 Burner, of internal diameter 9,5 mm 0,5 mm. A gaseous hydrocarbon fuel shall be used to provide the standard flame shown in Figure 2. This flame shall maintain a temperature of 1 000 C 100 C at a height of 13 mm 1 mm above the burner top. NOTE Propane, of at least 93 % purity, supplied thr

42、ough a jet of diameter 0,3 mm 0,1 mm, is suitable for provision of the specified flame and temperature. This jet size is such that the propane pressure required to obtain the standard flame is less than 7 kPa. 5.3 Wing top, having an opening of internal length 48 mm 1 mm and internal width 3,0 mm 0,

43、2 mm, fitted to the burner. 5.4 Support gauze, 215 mm long, 75 mm wide and having 13 mm of its length bent to form a right angle as shown in Figure 3. It shall consist of 6,4 mm mesh gauze constructed from 0,8 mm diameter stainless-steel wire. A minimum of four supports shall be available. EN ISO 35

44、82:2000+A1:2007 (E) 6 Dimensions in millimetres (the dimensions shown are internal) Key 1 Cabinet made from non-combustible material with draught-proof seal on lid and front panel 2 Toughened-glass sliding door with draught-proof seal 3 Ventilation slit 4 Ventilation chimney aIt is recommended that

45、the bottom of the window is approximately 25 mm below the normal position of the gauze during the test (see Figure 4) Figure 1 Test chamber EN ISO 3582:2000+A1:2007 (E) 7 Dimensions in millimetres Key 1 Test piece, 13 mm thick 2 Test piece support gauze, 6,4 mm mesh 3 Blue flame 4 Profile of visible

46、 flame, 38 mm high 5 Profile of inner cone, 6 mm high 6 Burner wing top Figure 2 Details of flame and relative positions of burner wing top, test piece and test piece support gauze EN ISO 3582:2000+A1:2007 (E) 8 Dimensions in millimetres Key 1 Burner wing top 2 Test piece 3 Test piece support gauze

47、Figure 3 Test piece and test piece support gauze 5.5 Support-gauze holder, constructed from mild steel as shown in Figure 4 so that: a) the gauze is maintained with its long axis within 1 of the horizontal, and parallel to the 600 mm dimension of the test chamber; b) the nearest end of the test piec

48、e is 13 mm 1 mm above the burner wing top (see Figure 2); c) the space both above and below the test piece is unobstructed; d) means is provided for positioning the burner in the correct position relative to the test piece; e) the gauze is equidistant from the front, back and sides of the test chamb

49、er, and is 175 mm 25 mm above the base of the test chamber. 5.6 Timing device, accurate to 1 s. 5.7 Measuring scale, graduated in millimetres. 5.8 Balance (if necessary), accurate to 1 mg. EN ISO 3582:2000+A1:2007 (E) 9 Dimensions in millimetres Figure 4 Support-gauze holder 6 Number, size, marking and weighing of test pieces 6.1 Cut ten test pieces from a representative sample of the material. Take care to remove all dust and any particles from the surfaces. 6.2 The standard test piece shall be 150 mm 1 mm long