DIN EN ISO 3452-3-2014 Non-destructive testing - Penetrant testing - Part 3 Reference test blocks (ISO 3452-3 2013) German version EN ISO 3452-3 2013《无损试验 渗透检测 第3部分 参考检测试块(ISO 3452.pdf

《DIN EN ISO 3452-3-2014 Non-destructive testing - Penetrant testing - Part 3 Reference test blocks (ISO 3452-3 2013) German version EN ISO 3452-3 2013《无损试验 渗透检测 第3部分 参考检测试块(ISO 3452.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 3452-3-2014 Non-destructive testing - Penetrant testing - Part 3 Reference test blocks (ISO 3452-3 2013) German version EN ISO 3452-3 2013《无损试验 渗透检测 第3部分 参考检测试块(ISO 3452.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、March 2014 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 1

2、9.100!%,Si“2094870www.din.deDDIN EN ISO 3452-3Non-destructive testing Penetrant testing Part 3: Reference test blocks (ISO 3452-3:2013);English version EN ISO 3452-3:2013,English translation of DIN EN ISO 3452-3:2014-03Zerstrungsfreie Prfung Eindringprfung Teil 3: Kontrollkrper (ISO 3452-3:2013);Eng

3、lische Fassung EN ISO 3452-3:2013,Englische bersetzung von DIN EN ISO 3452-3:2014-03Essais non destructifs Examen par ressuage Partie 3: Pices de rfrence (ISO 3452-3:2013);Version anglaise EN ISO 3452-3:2013,Traduction anglaise de DIN EN ISO 3452-3:2014-03SupersedesDIN EN ISO 3452-3:1999-02www.beuth

4、.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 11 pages02.14 DIN EN ISO 3452-3:2014-03 2 A comma is used as the decimal marker. National foreword This document (EN ISO 3452-3:2013) has been prepared by Technical Committee CEN/TC 138 “Non-destru

5、ctive testing” (Secretariat: AFNOR, France) in collaboration with Technical Committee ISO/TC 135 “Non-destructive testing”. The responsible German body involved in its preparation was the Normenausschuss Materialprfung (Materials Testing Standards Committee), Working Committee NA 062-08-25 AA Oberfl

6、chenverfahren. The DIN Standard corresponding to the International Standard referred to in this document is as follows: ISO 4957 DIN EN ISO 4957 Amendments This standard differs from DIN EN ISO 3452-3:1999-02 as follows: a) normative references have been updated; b) references to DIN EN ISO 3452-1 h

7、ave been updated; c) references to the certificate have been changed from 3.1.B to 3.1; d) Annex ZA has been deleted; e) the standard has been editorially revised. Previous editions DIN 54152-3: 1989-07 DIN EN ISO 3452-3: 1999-02 National Annex NA (informative) Bibliography DIN EN ISO 4957, Tool ste

8、els EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM November 2013 ICS 19.100 Supersedes EN ISO 3452-3:1998English Version Non-destructive testing - Penetrant testing - Part 3: Reference test blocks (ISO 3452-3:2013) Essais non destructifs - Examen par ressuage - Partie 3: Pices de rfrence (ISO 345

9、2-3:2013) Zerstrungsfreie Prfung - Eindringprfung - Teil 3: Kontrollkrper (ISO 3452-3:2013) This European Standard was approved by CEN on 19 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st

10、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,

11、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cro

12、atia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

13、United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.

14、 EN ISO 3452-3:2013 EEN ISO 3452-3 Contents Page Foreword . 3 1 Scope . 4 2 Normative references. 4 3 Description of reference blocks . 4 4 Type 1 reference block design and dimensions . 4 5 Type 2 reference block design and dimensions . 5 5.1 Design . 5 5.2 Measurement 8 6 Identification . 8 Biblio

15、graphy 9 2DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E) This document (EN ISO 3452-3:2013) has been prepared by Technical Committee CEN/TC 138 “Non-destructive testing , the secretariat of which is held by AFNOR, in collaboration with Technical Committee ISO/TC 135 Non-destructive testing . This E

16、uropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the latest by May 2014. Attention is drawn to the possibility that some of the elements

17、 of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 3452-3:1998. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following

18、 countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

19、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 3452-3:2013 has been approved by CEN as EN ISO 3452-3:2013 without any modification. Foreword“ ” Part 1: General principles Part 2: Testing of penetrant mat

20、erials Part 3: Reference test blocks Part 4: Equipment Part 5: Penetrant testing at temperatures higher than 50 C Part 6: Penetrant testing at temperatures lower than 10 C 3DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E)EN ISO 3452 consists of the following parts, under the general title Non-destruc

21、tive testing Penetrant testing: 1 ScopeThis International Standard describes two types of reference blocks: Type 1 reference blocks are used to determine the sensitivity levels of both fluorescent and colour contrast penetrant product families; Type 2 reference blocks are used for routine assessment

22、 of the performance of both fluorescent and colour contrast penetrant testing.The reference blocks are to be used in accordance with part 1 of this International Standard.2 Normative referencesThe following referenced documents, in whole or in part, are normatively referenced in this document and ar

23、e indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 10088-1, Stainless steels Part 1: List of standard stainless steelsEN 10204, Metallic products Types

24、of inspection documentsISO 4957, Tool steelsISO 10474, Steel and steel products Inspection documentsISO 15510, Stainless steels Chemical composition3 Description of reference blocksThe Type 1 reference block consists of a set of four nickel-chrome plated panels with 10 m, 20 m, 30 m and 50 m thickne

25、ss of plating, respectively. The 10 m, 20 m, 30 m and 50 m panels can be used for determination of the sensitivity of fluorescent penetrant systems. The sensitivity of colour contrast penetrant systems is determined using the 30 m and 50 m panels.The Type 2 reference block consists of a single panel

26、 of which one half has been plated with electroless nickel and a thin layer of chromium and the other half prepared to achieve areas of specific roughness. The plated side exhibits five star-shaped discontinuities.4 Type 1 reference block design and dimensionsThe Type 1 panels are rectangular in sha

27、pe with typical dimensions of 35 mm 100 mm 2 mm (see Figure 1). Each panel consists of a uniform layer of nickel-chromium plated on to a brass base, the thickness of nickel-chromium being 10 m, 20 m, 30 m and 50 m respectively. Transverse cracks are made in each panel by stretching the panels in the

28、 longitudinal direction. The width to depth ratio of each crack should be approximately 1:20.4DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E) Dimensions in millimetresKey1 Transverse cracks2 Nickel chromium plating, thickness 10 m, 20 m, 30 m or 50 mFigure 1 Test panel, reference block Type 1 (schem

29、atic)5 Type 2 reference block design and dimensions5.1 Design5.1.1 GeneralThe test panel (see Figure 2) is rectangular in shape with dimensions of 155 mm 50 mm 2,5 mm.NOTE All dimensional tolerances are 10 % unless otherwise stated.The base material is a stainless steel type X2 Cr Ni Mo 17-12-3 acco

30、rding to EN 10088-1 and ISO 15510 with initial hardness of HV 20 = 150 10 or equivalent.5DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E)Dimensions in millimetresFigure 2 Reference block Type 25.1.2 Rinsability areaFor checking the rinsability of penetrants, four adjacent areas sized 25 mm by 35 mm a

31、re produced down on one half of the test surface of the panel with roughnesses of Ra= 2,5 m, Ra= 5 m, Ra= 10 m and Ra= 15 m (see Figure 2).The area with Ra= 2,5 m may be produced by sand blasting and the other areas by electroerosion.5.1.3 Defect area5.1.3.1 GeneralThe defect area is located on the

32、other half of the test surface of the panel (see Figure 2).N1) National footnote: In the original ISO document, the key to Figure 2 has erroneously been left out. This has been corrected in the German version, and correspondingly in the English version. Key aRa-1,2 m up to 1,6 m N1)6DIN EN ISO 3452-

33、3:2014-03EN ISO 3452-3:2013 (E) The nickel layer shall be plated with a thin layer of hard chromium of 0,5 m to 1,5 m thickness. The panel shall then be heat treated to achieve a hardness value ranging from HV 0,3 = 900 to 1 000 by, for example, heating at 405 C for 70 min. The roughness Raof the ch

34、romium plating shall be 1,2 m to 1,6 m.5.1.3.3 Artificial defect productionFive equidistant indentations shall be made under loads typically in the range 2 kN to 8 kN on the reverse side of the test surface (plated area).For example, the production of the five artificial defects may be made using th

35、e following Table 1.Table 1 Defect numberDefect 1 2 3 4 5Applied force, kN 2,0 3,5 5,0 6,5 8,0The indentations for artificial defect production are made using a compression machine (120 kN capacity) or an appropriate Vickers hardness machine fitted with a hemispherical indentor.Details of the specif

36、ic indentor are given in Figure 3. The indentations are made using a speed loading of 0,05 kN/s and a speed unloading of 0,5 kN/s with continuous application of the load.Dimensions in millimetresFigure 3 Hemispherical indentorSteel designation: 90 MnCrV8 according to ISO 4957 at quenched and tempere

37、d condition or equivalent quality of hardness HRC 53 to 62.The five indentations shall be uniformly spaced and in size order, the smallest being adjacent to the least rough area.The artificial defects shall lie within circles having the diameters given in Table 2.5.1.3.2 PlatingA 60 m 3 m thickness

38、of electroless nickel shall be plated on to the test surface of the panel to achieve a hardness value ranging from HV 0,2 = 500 to 600.7DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E)Table 2 Typical diameter of crack areasDefect number Typical (diameter) dimensions (mm)1 32 3,53 44 4,55 5,55.2 Measu

39、rementThe size of each defect is determined optically at its maximum diameter using calibrated scales.A certificate, Type 3.1 according to ISO 10474 or EN 10204, giving the actual measured values of the five artificial defects and the roughnesses of the four rinsability areas shall accompany each re

40、ference block.6 IdentificationEach Type 1 reference block (set of panels) shall be identified with ISO 3452-3 followed by the identification of the supplier and a serial number. Each Type 2 reference block shall be identified with ISO 3452-3 followed the identification of the supplier and by serial

41、number.A declaration stating conformance to ISO 3452-3 and in line with ISO 10474 or EN 10204 Type 3.1 shall accompany each test block.8DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E) Bibliography1 EN 10027-1, Designation systems for steel Part 1: Steel names, principal symbols9DIN EN ISO 3452-3:2014-03EN ISO 3452-3:2013 (E)