DIN EN ISO 1580-2011 Slotted pan head screws - Product grade A (ISO 1580 2011) German version EN ISO 1580 2011《开槽平头螺钉 产品等级A(ISO 1580-2011) 德文版 EN ISO 1580-2011》.pdf

《DIN EN ISO 1580-2011 Slotted pan head screws - Product grade A (ISO 1580 2011) German version EN ISO 1580 2011《开槽平头螺钉 产品等级A(ISO 1580-2011) 德文版 EN ISO 1580-2011》.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 1580-2011 Slotted pan head screws - Product grade A (ISO 1580 2011) German version EN ISO 1580 2011《开槽平头螺钉 产品等级A(ISO 1580-2011) 德文版 EN ISO 1580-2011》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、December 2011 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 21.060.10!$xXf“1855367www.din.deDDIN EN ISO 1580Slotted pan head screws Product grade A (ISO 1580:2011)English translation of DIN EN ISO 1580:2011-12Flachkopfschrauben mit Schlitz Produktklasse A (ISO 1580:2011)Englische bersetzung von DIN EN ISO 1580:2011-12Vis mtaux tte cylindrique large fendue

3、Grade A (ISO 1580:2011)Traduction anglaise de DIN EN ISO 1580:2011-12SupersedesDIN EN ISO 1580:1994-10www.beuth.deDocument comprises 13 pagesIn case of doubt, the German-language original shall be considered authoritative.11.11 DIN EN ISO 1580:2011-12 2 A comma is used as the decimal marker. Nationa

4、l foreword This standard has been prepared by Technical Committee ISO/TC 2 “Fasteners” in collaboration with Technical Committee CEN/TC 185 “Fasteners” (both secretariats are held by DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Mechanische Verbin-dun

5、gselemente (Fasteners Standards Committee), Working Committee NA 067-00-05 AA Kleinschrauben und gewindeformende Schrauben. The DIN 4000-160-2 tabular layout of article characteristics shall apply to screws covered in this standard. The DIN Standards corresponding to the International Standards refe

6、rred to in Clause 2 of this document are as follows: ISO 225 DIN EN ISO 225 ISO 261 DIN ISO 261 ISO 898-1 DIN EN ISO 898-1 ISO 965-2 DIN ISO 965-2 ISO 3269 DIN EN ISO 3269 ISO 3506-1 DIN EN ISO 3506-1 ISO 4042 DIN EN ISO 4042 ISO 4759-1 DIN EN ISO 4759-1 ISO 6157-1 DIN EN 26157-1 ISO 8839 DIN EN 288

7、39 ISO 8992 DIN ISO 8992 ISO 10683 DIN EN ISO 10683 Amendments This standard differs from DIN EN ISO 1580:1994-10 as follows: a) normative references are now undated; b) in Table 2, zinc-flake coatings in accordance with DIN EN ISO 10683 have been added; c) Annex ZA has been deleted. Previous editio

8、ns DIN 85: 1921-08, 1926-01, 1937-01, 1942-10, 1952-12, 1964-04, 1970-06, 1972-12, 1988-10, 1990-08 DIN 572: 1923-02 DIN 576: 1923-02 DIN ISO 1580: 1990-08 DIN EN ISO 1580: 1994-10 DIN EN ISO 1580:2011-12 3 National Annex NA (informative) Bibliography DIN 4000-160, Tabular layout of product properti

9、es Part 160: Fasteners with external thread DIN EN 26157-1, Fasteners Surface discontinuities Bolts, screws and studs subject to general requirements DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nut

10、s Symbols and descriptions of dimensions DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, M

11、echanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 10683, Fasteners Non-electrol

12、ytically applied zinc flake coatings DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality DIN ISO 8992, Fasteners General re

13、quirements for bolts, screws, studs and nuts DIN EN ISO 1580:2011-12 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1580 September 2011 ICS 21.060.10 Supersedes EN ISO 1580:1994English Version Slotted pan head screws - Product grade A (ISO 1580:2011) Vis

14、mtaux tte cylindrique large fendue - Grade A (ISO 1580:2011) Flachkopfschrauben mit Schlitz - Produktklasse A (ISO 1580:2011) This European Standard was approved by CEN on 8 August 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givi

15、ng this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offi

16、cial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of

17、 Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

18、 EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1580:2011: EContent

19、s DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 2 Page Foreword3 1 Scope 4 2 Normative references 4 3 Dimensions.5 4 Specifications and reference International Standards 7 5 Designation 8 Bibliography 9 Foreword This document (EN ISO 1580:2011) has been prepared by Technical Committee ISO/TC 2 Fasten

20、ers” in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2012, and conflicting national

21、standards shall be withdrawn at the latest by March 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN

22、ISO 1580:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

23、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1580:2011 has been approved by CEN as a EN ISO 1580:2011 without any modification. “

24、DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 3 1 Scope This International Standard specifies the characteristics of slotted pan head screws of product grade A and with threads from M1,6 to M10 inclusive. If, in special cases, specifications other than those listed in this International Standard are

25、required, they can be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, ISO 965-2 and ISO 3506-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited appl

26、ies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 261, ISO general purpose metric screw threads General plan ISO 898-1, Mechanical properties of fa

27、steners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quali

28、ty ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electroplated coatings ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B an

29、d C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Faste

30、ners Non-electrolytically applied zinc flake coatings DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 4 3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225. The shank diameter is approximately equal to the pitch diameter or equal to the permissible maj

31、or thread diameter. Key 1 as-rolled end Figure 1 DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 5 Table 1 Dimensions Dimensions in millimetres Thread, d M1,6 M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 Pb0,35 0,4 0,45 0,5 0,6 0,7 0,8 1 1,25 1,5 a max. 0,7 0,8 0,9 1 1,2 1,4 1,6 2 2,5 3 b min. 25 25 25 25 38 38 3

32、8 38 38 38 nom. = max. 3,2 4,0 5,0 5,6 7,00 8,00 9,50 12,00 16,00 20,00 dkmin. 2,9 3,7 4,7 5,3 6,64 7,64 9,14 11,57 15,57 19,48 damax. 2 2,6 3,1 3,6 4,1 4,7 5,7 6,8 9,2 11,2 nom. = max. 1,00 1,30 1,50 1,80 2,10 2,40 3,00 3,6 4,8 6,0 k min. 0,86 1,16 1,36 1,66 1,96 2,26 2,86 3,3 4,5 5,7 nom. 0,4 0,5

33、0,6 0,8 1 1,2 1,2 1,6 2 2,5 max. 0,60 0,70 0,80 1,00 1,20 1,51 1,51 1,91 2,31 2,81 n min. 0,46 0,56 0,66 0,86 1,06 1,26 1,26 1,66 2,06 2,56 r min. 0,1 0,1 0,1 0,1 0,1 0,2 0,2 0,25 0,4 0,4 rfref. 0,5 0,6 0,8 0,9 1 1,2 1,5 1,8 2,4 3 t min. 0,35 0,5 0,6 0,7 0,8 1 1,2 1,4 1,9 2,4 w min. 0,3 0,4 0,5 0,7

34、0,8 1 1,2 1,4 1,9 2,4 x max. 0,9 1 1,1 1,25 1,5 1,75 2 2,5 3,2 3,8 lacnom. min. max. Approximate mass, in kilograms per 1 000 pieces ( = 7,85 kg/dm3) (for information only) 2 1,8 2,2 0,075 2,5 2,3 2,7 0,081 0,152 3 2,8 3,2 0,087 0,161 0,281 4 3,76 4,24 0,099 0,18 0,311 0,463 5 4,76 5,24 0,11 0,198 0

35、,341 0,507 0,825 1,16 6 5,76 6,24 0,122 0,217 0,371 0,551 0,885 1,24 2,12 8 7,71 8,29 0,145 0,254 0,431 0,639 1 1,39 2,37 4,02 10 9,71 10,29 0,168 0,292 0,491 0,727 1,12 1,55 2,61 4,37 9,38 12 11,65 12,35 0,192 0,329 0,551 0,816 1,24 1,7 2,86 4,72 10 18,2 (14) 13,65 14,35 0,215 0,366 0,611 0,904 1,3

36、6 1,86 3,11 5,1 10,6 19,2 16 15,65 16,35 0,238 0,404 0,671 0,992 1,48 2,01 3,36 5,45 11,2 20,2 20 19,58 20,42 0,478 0,792 1,17 1,72 2,32 3,85 6,14 12,6 22,2 25 24,58 25,42 0,942 1,39 2,02 2,71 4,47 7,01 14,1 24,7 30 29,58 30,42 1,61 2,32 3,1 5,09 7,9 15,7 27,2 35 34,5 35,5 2,62 3,48 5,71 8,78 17,3 2

37、9,7 40 39,5 40,5 3,87 6,32 9,66 18,9 32,2 45 44,5 45,5 6,94 10,5 20,5 34,7 DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 6 Table 1 (continued) Dimensions in millimetres Thread, d M1,6 M2 M2,5 M3 (M3,5)aM4 M5 M6 M8 M10 la cnom. min. max. Approximate mass, in kilograms per 1 000 pieces ( = 7,85 kg/dm3)

38、 (for information only) 50 49,5 50,5 7,56 11,4 22,1 37,2 (55) 54,05 55,95 12,3 23,7 39,7 60 59,05 60,95 13,2 25,3 42,2 (65) 64,05 65,95 26,9 44,7 70 69,05 70,95 28,5 47,2 (75) 74,05 75,95 30,1 49,7 80 79,05 80,95 31,7 52,2 NOTE Preferred lengths are those between the solid, bold, stepped lines. aSiz

39、es in parentheses should be avoided if possible. bP is the pitch of the thread. cScrews with nominal lengths above the bold, discontinuous line are threaded up to the head; b = l a. 4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International

40、 Standards Material Steel Stainless steel Non-ferrous metal General requirements International Standard ISO 8992 Tolerance class 6g Thread International Standard ISO 261, ISO 965-2 Property class 4.8, 5.8 A2-50, A2-70 Mechanical property International Standard ISO 898-1 ISO 3506-1 ISO 8839 Product g

41、rade A Tolerance International Standard ISO 4759-1 As processed Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Finish Coating Additional requirements or other finishes or coatings shall be agree

42、d between the supplier and the purchaser. Surface integrity Limits for surface discontinuities are specified in ISO 6157-1. Acceptability Acceptance inspection is specified in ISO 3269. DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 7 5 Designation EXAMPLE A slotted pan head screw with thread M5, nomi

43、nal length l = 20 mm and property class 4.8 is designated as follows: Pan head screw ISO 1580 - M5 20 - 4.8 DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 8 Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose bolts DIN EN ISO 1580:2011-12 EN ISO 1580:2011 (E) 9