DIN EN ISO 14245-2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing (ISO 14245 2006) German version EN ISO 14245 2010《气瓶 液化石油气瓶阀门的规范和试验 自闭合(ISO 1.pdf

《DIN EN ISO 14245-2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing (ISO 14245 2006) German version EN ISO 14245 2010《气瓶 液化石油气瓶阀门的规范和试验 自闭合(ISO 1.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 14245-2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing (ISO 14245 2006) German version EN ISO 14245 2010《气瓶 液化石油气瓶阀门的规范和试验 自闭合(ISO 1.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、November 2010 Translation by DIN-Sprachendienst.English price group 14No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 23.060.20!$l22“1731515www.din.deDDIN EN ISO 14245Gas cylinders Specifications and testing of LPG cylinder valves Self-closing (ISO 14245:2006)English translation of DIN EN ISO 14245:2010-11Gasflaschen Spezifikation und Prfung von Flaschenventilen fr Flssiggas (LPG) Selbstschlieend (ISO 14245:2006

3、)Englische bersetzung von DIN EN ISO 14245:2010-11Bouteilles gaz Spcifications et essais pour valves de bouteilles de GPL Fermeture automatique (ISO 14245:2006)Traduction anglaise de DIN EN ISO 14245:2010-11SupersedesDIN EN 13152:2003-09www.beuth.deDocument comprises pagesIn case of doubt, the Germa

4、n-language original shall be considered authoritative.2711.10 DIN EN ISO 14245:2010-11 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” and has been taken over by Technical Committee CEN/TC 286 “Liquefied petr

5、oleum gas equipment and accessories” (Secretariat: NSAI, Ireland). The responsible German body involved in its preparation was the Normenausschuss Druckgasanlagen (Pressurized Gas Installations Standards Committee), Working Committee NA 016-00-06 AA Flssiggas-Gerte und Ausrstung; Spiegelausschuss zu

6、 CEN/TC 286. A minor discrepancy in ISO 14245:2006 was not discovered until CEN decided to adopted that standard unchanged. In Clause 2, Table 1, the test temperature for test no. 16 is given as 65 (/2,5) C, while in 5.18 this temperature is given as 65 C (/5) C. The first-mentioned tolerance (/2,5)

7、 C is to be taken. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 11114-1 DIN EN ISO 11114-1 ISO 11114-2 DIN EN ISO 11114-2 ISO 11116-1 DIN EN ISO 11116-1 ISO 10920 and ISO 11116-1 have been replaced by ISO 11363-1 which has been taken

8、 over as DIN EN ISO 11363-1. Amendments This standard differs from DIN EN 13152:2003-09 as follows: a) the standard has been brought in line with the current rules of presentation; b) normative references have been updated; c) terms and definitions have been expanded and given in more detail. Previo

9、us editions DIN EN 13152: 2002-03, 2003-09 DIN EN ISO 14245:2010-11 3 National Annex NA (informative) Bibliography DIN EN ISO 11114-1, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials DIN EN ISO 11114-2, Transportable gas cylinder

10、s Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials DIN EN ISO 11116-1, Transportable gas cylinders Gas cylinders 17E taper thread for connection of valves to gas cylinders Part 1: Specification DIN EN ISO 11363-1, Gas cylinders 17E and 25E taper threads

11、for connection of valves to gas cylinders Part 1: Specification DIN EN ISO 14245:2010-11 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14245 June 2010 ICS 23.020.30 Supersedes EN 13152:2001English Version Gas cylinders - Specifications and testing of LPG

12、 cylinder valves - Self-closing (ISO 14245:2006) Bouteilles gaz - Spcifications et essais pour valves de bouteilles de GPL - Fermeture automatique (ISO 14245:2006) Gasflaschen - Spezifikation und Prfung von Flaschenventilen fr Flssiggas (LPG) - Selbstschlieend (ISO 14245:2006) This European Standard

13、 was approved by CEN on 20 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such na

14、tional standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language an

15、d notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

16、 Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN Al

17、l rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 14245:2010: EContents DIN EN ISO 14245:2010-11 EN ISO 14245:2010 (E) 2 Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Design and specific

18、ation 8 4.1 General8 4.2 Materials .8 4.3 Essential components.9 4.4 Optional components10 4.5 Leak tightness11 5 Valve type test11 5.1 General11 5.2 Test procedure and test requirements 11 5.3 External and internal tightness tests (Tests nos. 2, 6, 8, 9, 10, 12, 14, 15, 16 and 17)13 5.4 External an

19、d internal tightness test (Test no. 2) 14 5.5 Valve closure test (Test no. 3)14 5.6 Operation test (Test no. 4) 15 5.7 Valve stem test (Test no. 5) 15 5.8 External and internal tightness test (Test no. 6) 16 5.9 Impact test (Test no. 7)16 5.10 External and internal tightness test (Test no. 8) 16 5.1

20、1 External and internal tightness test (Test no. 9) 16 5.12 External and internal tightness test after ageing (Test no. 10).17 5.13 Endurance test Part 1 (Test no. 11).17 5.14 External and internal tightness test after endurance test Part 1 (Test no. 12) .17 5.15 Endurance test Part 2 (Test no. 13).

21、17 5.16 Tightness test at valve outlet seal after endurance test Part 2 (Test no. 14)18 5.17 External and internal tightness test (Test no. 15) 18 5.18 External and internal tightness test High temperature (Test no. 16).18 5.19 External and internal tightness test Low temperature (Test no. 17)18 5.2

22、0 Simulated vacuum test (Test no. 18) .18 5.21 Examination of dismantled valves nos. 4, 5 and 6 (Test no. 19).19 5.22 Acceptance criteria19 6 Documentation/test report19 6.1 Documentation.19 6.2 Test report 19 7 Markings .19 Annex A (normative) Valve dimensions20 Annex B (informative) Production tes

23、ting and inspection21 Annex C (normative) Special low temperature requirements for valves.22 Bibliography 23 Foreword The text of ISO 14245:2006 has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” of the International Organization for Standardization (ISO) and has been taken over as E

24、N ISO 14245:2010 by Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories” the secretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Dec

25、ember 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such pat

26、ent rights. This document supersedes EN 13152:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland

27、, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 14245:2006 has been approved by CEN as a EN ISO

28、 14245:2010 without any modification. DIN EN ISO 14245:2010-11 EN ISO 14245:2010 (E) 3 Introduction This International Standard calls for the use of substances and procedures that can be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not a

29、bsolve the user from legal obligations relating to health and safety at any stage. It has been assumed in the drafting of this International Standard that execution of its provisions is entrusted to appropriately qualified and experienced people. DIN EN ISO 14245:2010-11 EN ISO 14245:2010 (E) 4 1 Sc

30、ope This International Standard specifies the requirements for design, specification and type testing for dedicated LPG self-closing cylinder valves specifically for use with transportable refillable LPG cylinders from 0,5 l up to 150 l water capacity. It includes references to associated equipment

31、for vapour or liquid service. NOTE Annex B gives recommendations for production testing and inspection. This International Standard does not apply to fixed automotive installations. 2 Normative references The following referenced documents are indispensable for the application of this document. For

32、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 10920, Gas cylinders 25E taper thread for connection of valves to gas cylinders Specification ISO 11114-1, Transportable gas cylinders Compa

33、tibility of cylinder and valve materials with gas contents Part 1: Metallic materials ISO 11114-2, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials ISO 11116-1, Gas cylinders 17E taper thread for connection of valves to gas cy

34、linders Part 1: Specifications 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 liquefied petroleum gas LPG mixture of predominantly butane or propane with traces of other hydrocarbon gases classified in accordance with UN number 1965, hydroca

35、rbon gas mixture, liquefied, or NOS or UN number 1075, petroleum gases, liquefied NOTE In some countries, UN number 1011 and UN number 1978 may also be used to designate LPG. ISO 10464 DIN EN ISO 14245:2010-11 EN ISO 14245:2010 (E) 5 3.2 cylinder valve valve designed for use in one or more of the fo

36、llowing applications: liquid filling, liquid service, vapour service, liquid level indication 3.3 external tightness resistance to leakage through the valve body to or from the atmosphere, when the valve is open 3.4 internal tightness resistance to leakage across the valve seat, or other internal se

37、aling components, when the valve is closed 3.5 eduction tube tube fitted to the valve to allow withdrawal of liquid LPG with the cylinder in its normal operating position 3.6 fixed liquid level gauge control device, such as a dip tube in combination with a vent valve, to verify that the predetermine

38、d maximum liquid level in a cylinder has been reached or surpassed 3.7 liquid level indicator control device, such as a float gauge, permitting the gauging of the liquid level in the cylinder 3.8 valve body major valve component including valve stem and/or valve outlet and, where applicable, the pro

39、vision for other optional components 3.9 excess flow device flow limiter device designed to close or partially close when the flow of liquid or vapour passing through it exceeds a predetermined value and to re-open when the pressure differential across the valve has been restored below a certain val

40、ue 3.10 non-return valve valve designed to close automatically to restrict reverse flow 3.11 vapour/liquid dual valve valve designed to allow vapour and liquid withdrawal from a cylinder in its normal operating position 3.12 sealing element element used to provide internal leak tightness 3.13 valve

41、stem section of the valve body which connects to the cylinder 3.14 valve outlet section of the valve body to which a regulator or connector can be fitted for vapour or liquid withdrawal NOTE The valve outlet is also normally used for filling the cylinder. DIN EN ISO 14245:2010-11 EN ISO 14245:2010 (

42、E) 6 3.15 type test test or series of tests conducted to prove that the design meets the requirements of this International Standard 3.16 cylinder opening part of the cylinder to which the valve stem connects 3.17 quick coupling connector system which enables an appliance or equipment to be connecte

43、d to a cylinder valve without the use of tools 3.18 test pressure pressure at which the valve or component is tested in bar gauge 3.19 sediment tube device designed to reduce the risk of foreign matter, which can be in the cylinder, from entering the valve 3.20 protection cap/dust cap device fitted

44、to the valve outlet and intended for one or more of the following functions: to protect the outlet; to prevent the ingress of foreign matter; to indicate unauthorized manipulation 3.21 sealing cap device fitted to, or integral with, the outlet of the cylinder valve to provide secondary closure 3.22

45、valve operating mechanism mechanism that opens the valve when, or after, a regulator or connector is fitted and closes automatically when, or before, a regulator or connector is disconnected 3.23 sealing mechanism mechanism to obtain internal leak tightness 3.24 protection cap device that may be scr

46、ewed to a fitting permanently attached to the cylinder to protect a cylinder valve 3.25 shroud/guard device that may be welded to the cylinder to protect a cylinder valve 3.26 gross mass mass of the heaviest cylinder on which the valve is intended to be fitted, including any permanently attached acc

47、essories and the maximum mass of the LPG content DIN EN ISO 14245:2010-11 EN ISO 14245:2010 (E) 7 3.27 pressure relief valve valve which automatically, without the assistance of any energy other than that of the fluid concerned, discharges a quantity of fluid so as to prevent a predetermined safe pr

48、essure being exceeded, and which is designed to re-close and prevent the further flow of fluid after normal pressure conditions of service have been restored NOTE The loading due to the fluid pressure underneath the valve-sealing element is opposed by a spring. 4 Design and specification 4.1 General

49、 The valve shall be capable of withstanding: operating pressures and test pressures; mechanical stresses, including dynamic loads such as pressure shocks or cyclic changes; operating temperatures. NOTE Pressures are gauge pressure unless otherwise specified. There shall be valve external and internal leak tightness for the full range of pressure and temperature conditions. The specific requirements relating to the functions, mechanical strength, pressure, operating temperatures, ext