DIN EN 16068-2012 Packaging - Rigid plastic containers - PET finish 38 German version EN 16068 2011《包装 硬质塑料容器 聚酯修饰38 德文版本EN 16068-2011》.pdf

《DIN EN 16068-2012 Packaging - Rigid plastic containers - PET finish 38 German version EN 16068 2011《包装 硬质塑料容器 聚酯修饰38 德文版本EN 16068-2011》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 16068-2012 Packaging - Rigid plastic containers - PET finish 38 German version EN 16068 2011《包装 硬质塑料容器 聚酯修饰38 德文版本EN 16068-2011》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、February 2012 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 55.100!$y“1866196www.din.deDDIN EN 16068Packaging Rigid plastic containers PET finish 38English translation of DIN EN 16068:2012-02Verpackung Kunststoffbehltnisse PET-Verschlussmundstck 38Englische bersetzung von DIN EN 16068:2012-02Emballage Rcipients en plastique rigide Bague PET 38Traduction an

3、glaise de DIN EN 16068:2012-02www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.9 01.12 DIN EN 16068:2012-02 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 261

4、 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Working Committee NA 115-02-09 AA Behltnisse aus Kunststoff. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16068 Novembe

5、r 2011 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish 38 This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

6、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa

7、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia,

8、 Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATI

9、ON COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16068:2011: EEmballage - Rcipients en plastique rigide - Bag

10、ue PET 38 Verpackung - Kunststoffbehltnisse - PET-Verschlussmundstck 38 EN 16068:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Dimensions .53 Requirements .5Bibliography 7DIN EN 16068:2012-02 EN 16068:2011 (E) 3 Foreword This document (EN 16068:2011) has been prepared by Technical Com

11、mittee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the lat

12、est by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stand

13、ards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

14、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 16068:2012-02 EN 16068:2011 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Packaging) data sheet GME 30.25 (2009) 1. Efficient pac

15、kaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. DIN EN 16068:2012-02 EN 16068:2011 (E) 5 1 Scope This European Standard specifies the dimensions of the 38 mm screw finis

16、h with three (3) thread starts for flat waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen (0,7 bar max.). This finish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will

17、 separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure shell. This finish is for non crystallized necks only. 2 Dimensions 2.1 The design and dimensions of the finish shal

18、l be as shown in Figure 1. 2.2 Dimensions of the 3 thread starts 120 apart. 180 of full depth thread per lead R 7,5 thread lead-in R 7,5 thread run-out Lead: 9 mm (travel per turn) 2.3 General tolerance for other radii: 0,05 mm 2.4 Weight on height 16,5 mm (density = 1,335): Z = 41,0 mm Weight 4,18

19、g Z = 44,0 mm Weight 4,57 g 3 Requirements The following requirements apply: This finish is a top, side and inside seal finish. This finish shall be smooth and free of any defects that will contribute to leaks. Flash shall not exceed 0,13 mm per side, and shall not be continuous. On the blown bottle

20、, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and across the sealing surface of the finish. Requirements for good closure application on finish: 0,13 mm max. out-of-parallel sealing surface with neck support ledge is allowed; an offset or vertical mismat

21、ch of thread is not to exceed 0,10 mm at the mould seam. T dimension is not measured in the depressed area. Variations in E are to follow uniformly those of T. In case of usage for a sensitive product, the bottler shall check that the closure is suitable for this usage. DIN EN 16068:2012-02 EN 16068

22、:2011 (E) 6 Dimensions in millimetres Key 1 start thread 4 straight 2 radius centre 5 thread lead-in 3 thread starts 120 apart Figure 1 Design and dimensions of the finish DIN EN 16068:2012-02 EN 16068:2011 (E) 7 Bibliography 1 CE.T.I.E. data sheet GME 30.25 PET finish 38 2009 C.E.T.I.E. : International Technical Centre for Bottling and related Packaging 112 114 rue La Botie 75008 Paris www.cetie.org DIN EN 16068:2012-02