DIN EN 14141-2013 Valves for natural gas transportation in pipelines - Performance requirements and tests German version EN 14141 2013《天然气输送管道用阀门 性能要求和试验 德文版本EN 14141-2013》.pdf

《DIN EN 14141-2013 Valves for natural gas transportation in pipelines - Performance requirements and tests German version EN 14141 2013《天然气输送管道用阀门 性能要求和试验 德文版本EN 14141-2013》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 14141-2013 Valves for natural gas transportation in pipelines - Performance requirements and tests German version EN 14141 2013《天然气输送管道用阀门 性能要求和试验 德文版本EN 14141-2013》.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、August 2013 Translation by DIN-Sprachendienst.English price group 18No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、 23.060.01; 75.200!%(v“2052783www.din.deDDIN EN 14141Valves for natural gas transportation in pipelines Performance requirements and tests;English version EN 14141:2013,English translation of DIN EN 14141:2013-08Armaturen fr den Transport von Erdgas in Fernleitungen Anforderungen an die Gebrauchstau

3、glichkeit und deren Prfung;Englische Fassung EN 14141:2013,Englische bersetzung von DIN EN 14141:2013-08Robinetterie pour le transport de gaz naturel par des pipelines Exigences de performance et essais;Version anglaise EN 14141:2013,Traduction anglaise de DIN EN 14141:2013-08SupersedesDIN EN 14141:

4、2004-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 43 pages 08.13 DIN EN 14141:2013-08 2 A comma is used as the decimal marker. National foreword This document (EN 14141:2013) has been prepared by Technical Committee CEN/TC 69 “Indu

5、strial valves” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Armaturen (Valves Standards Committee), Working Committee NA 003-01-09 AA Armaturen fr die Erdlindustrie. Amendments This standard differs from DIN EN 14141:2004-03 as follows

6、: a) Clause 1 “Scope” has been revised; b) Clause 2 “Normative references” has been updated; c) Clause 5 “Requirements and tests” has been revised and a new Subclause 5.3.5 “Seals” has been added; d) Clause 10 “Marking” has been added; e) Table A.1 “Nominal size ranges” has been extended; f) the for

7、mer Annex B “Functional test on behaviour of valve sealing materials towards liquids in natural gas” has been deleted; g) the Bibliography has been updated. Previous editions DIN 3230-5: 1977-01, 1981-09, 1984-08 DIN 3437: 1990-06 DIN EN 14141: 2004-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NO

8、RM EN 14141 June 2013 ICS 23.060.01; 75.200 Supersedes EN 14141:2003English Version Valves for natural gas transportation in pipelines - Performance requirements and tests Robinetterie pour le transport de gaz naturel par des pipelines - Exigences de performance et essais Armaturen fr den Transport

9、von Erdgas in Fernleitungen -Anforderungen an die Gebrauchstauglichkeit und deren Prfung This European Standard was approved by CEN on 18 April 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

10、of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa

11、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia,

12、 Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Unite

13、d Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14141:2013: E

14、EN 14141:2013 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .7 4 Functional requirements .8 5 Requirements and tests 9 6 Inspection 23 7 Quality 23 8 Type tests 23 9 Functional and other qualification tests 23 10 Marking 24 Annex A (normati

15、ve) Type test on general design and production of pipeline valves . 25 Annex B (normative) Strength test on torque/thrust 30 Annex C (normative) Functional test on clean gas (on option) 31 Annex D (normative) Functional test for abrasion resistance to dirty service of ball valves (on option) 32 Anne

16、x E (normative) Wall thickness measurement 34 Annex F (informative) Additional requirements 35 Annex G (informative) Summary of tests on product and type tests . 36 Bibliography . 41 DIN EN 14141:2013-08 EN 14141:2013 (E) 3 Foreword This document (EN 14141:2013) has been prepared by Technical Commit

17、tee CEN/TC 69 “Industrial Valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn a

18、t the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14141:2003. The main change

19、s compared to the previous edition are listed below: the scope was adjusted and revised; Clause 5 was specified and revised; Clause 10 was added; Annexes B, F and G were added; entire document was editorially revised and adjusted. According to the CEN-CENELEC Internal Regulations, the national stand

20、ards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

21、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14141:2013-08 EN 14141:2013 (E) 4 Introduction CEN/TC 69/WG 9 has been responsible for the development of a European performance standard of valves f

22、or use in pipelines for transportation of natural gas in accordance with EN 1594. The significant properties of valves designed for a special application are defined by performance requirements accompanied by the description of tests to be carried out: by the manufacturer on the product during the m

23、anufacture; and by an independent accepted body on test samples for certification purposes; to give proof that the valve meets the performance requirements of this European Standard. A type test is included in this European Standard to satisfy the requirements of EN 1594. DIN EN 14141:2013-08 EN 141

24、41:2013 (E) 5 1 Scope This European Standard applies to all valves (plug, ball, gate and check valves) used in onshore transmission pipelines for transport of natural gas in accordance with EN 1594, but with a differing temperature range according to the following three classes in accordance with EN

25、 682: 1) - 10 C to 60 C; 2) - 20 C to 60 C; 3) the range stated by the purchaser for special design. This European Standard comprises all valves which are components of the pipeline. This European Standard specifies valves for pipelines with a maximum operating pressure (MOP) over 16 bar. Control va

26、lves and safety valves are excluded from the scope of this European Standard. This European Standard specifies requirements and appropriate verification tests carried out during production and for certification purposes to verify that the valves conform to the requirements. A summary of the product

27、and type tests is given in Annex G. This European Standard makes reference to EN 13942. All the requirements of EN 13942 should be met unless otherwise stated. Paragraphs marked with a dot indicate requirements which are identical to EN 13942. Additional national requirements and tests in accordance

28、 with individual national legal regulations not yet harmonised may be necessary and are to be advised in the purchase order. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated reference

29、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 19, Industrial valves - Marking of metallic valves EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment EN 558, Industrial

30、 valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves EN 571-1, Non destructive testing - Penetrant testing - Part 1: General principles EN 682, Elastomeric Seals - Materials requirements for seals used in pipes and fittings

31、 carrying gas and hydrocarbon fluids EN 736-1:1995, Valves - Terminology - Part 1: Definition of types of valves EN 736-2:1997, Valves - Terminology - Part 2: Definition of components of valves EN 736-3:2008, Valves - Terminology - Part 3: Definition of terms EN 1369:2012, Founding - Magnetic partic

32、le testing EN 1371-1:2011, Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings DIN EN 14141:2013-08 EN 14141:2013 (E) 6 EN 1435:1997, Non-destructive examination of welds Radiographic examination of welded joints EN 1503-1, Valves - Materials for bodies, bonn

33、ets and covers - Part 1: Steels specified in European Standards EN 1503-2, Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards EN 1515-1, Flanges and their joints - Bolting - Part 1: Selection of bolting EN 1515-2, Flanges and their joi

34、nts - Bolting - Part 2: Classification of bolt materials for steel flanges, PN designated EN 1594, Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements EN 10204:2004, Metallic products - Types of inspection documents EN 10228-1:1999, Non-destructive tes

35、ting of steel forgings - Part 1: Magnetic particle inspection EN 10228-2:1998, Non-destructive testing of steel forgings - Part 2: Penetrant testing EN 10228-3:1998, Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings EN 10228-4, Non-destr

36、uctive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings EN 12266-1:2012, Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements EN 12516-1, Industri

37、al valves - Shell design strength - Part 1: Tabulation method for steel valve shells EN 12516-2, Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells EN 12516-3, Valves - Shell design strength - Part 3: Experimental method EN 12517-1:2006, Non-destructive tes

38、ting of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels EN 12627:1999, Industrial valves - Butt welding ends for steel valves EN 12681, Founding - Radiographic examination EN 12982, Industrial valves - End-to-end and centre-t

39、o-end dimensions for butt welding end valves EN 13942:2009, Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified) EN ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1) EN ISO 5210, Industrial valv

40、es - Multi-turn valve actuator attachments (ISO 5210) EN ISO 5211, Industrial valves - Part-turn actuator attachments (ISO 5211) EN ISO 9712:2012, Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) DIN EN 14141:2013-08 EN 14141:2013 (E) 7 EN ISO 10497, Testing

41、 of valves - Fire type-testing requirements (ISO 10497) EN ISO 11666:2010, Non-destructive testing of welds - Ultrasonic testing - Acceptance levels (ISO 11666:2010) EN ISO 17637, Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637) EN ISO 17638, Non-destructive test

42、ing of welds - Magnetic particle testing (ISO 17638) EN ISO 17640:2010, Non-destructive testing of welds - Ultrasonic testing - Techniques, testing levels, and assessment (ISO 17640:2010) EN ISO 23277:2009, Non-destructive testing of welds - Penetrant testing of welds - Acceptance levels (ISO 23277:

43、2006) EN ISO 23278:2009, Non-destructive testing of welds Magnetic particle testing of welds Acceptance levels (ISO 23278:2006) MSS-SP-55-20061), Quality standard for steel castings for valves, flanges and fittings and other piping components (visual method for evaluation of surface irregularities)

44、3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 736-1:1995, EN 736-2:1997, EN 736-3:2008 and EN 13942:2009 and the following apply. 3.1 full opening valve valve with an unobstructed opening capable of allowing a sphere or other internal devices of the

45、 same nominal size as the valve to pass 3.2 maximum pressure differential (MPD) maximum difference between the upstream and downstream pressure across the obturator at which the obturator may be operated 3.3 reduced-opening valve valve with the opening through the obturator smaller than at the end c

46、onnection(s) 3.4 seating surfaces contact surfaces of the obturator and seat which ensure valve sealing 3.5 stem part that connects the obturator to the operator and which may consist of one or more components Note 1 to entry: This definition applies also for shafts. 3.6 test report 1)Developed and

47、approved by the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 127 Park Street, NE, Vienna, Virginia 22180.DIN EN 14141:2013-08 EN 14141:2013 (E) 8 written statement comprising the results of the particular tests for the evaluation of the conformity of a range of valv

48、es to this European Standard 3.7 type test test carried out on one or more valves representative of the design and the manufacturing process to confirm conformance of the manufactured valves with specified requirements Note 1 to entry: A range may include valves of the same design, the same material group and the same manufacturing method but with different size designations and different allowable pressures. 3.8 type test certification granting of a certificate by an independent accepted body to prov