DIN EN 13081-2012 Tanks for transport of dangerous goods - Service equipment for tanks - Vapour collection adaptor and coupler German version EN 13081 2008+A1 2012《危险品运输用槽罐 槽罐用维护设备.pdf

《DIN EN 13081-2012 Tanks for transport of dangerous goods - Service equipment for tanks - Vapour collection adaptor and coupler German version EN 13081 2008+A1 2012《危险品运输用槽罐 槽罐用维护设备.pdf》由会员分享，可在线阅读，更多相关《DIN EN 13081-2012 Tanks for transport of dangerous goods - Service equipment for tanks - Vapour collection adaptor and coupler German version EN 13081 2008+A1 2012《危险品运输用槽罐 槽罐用维护设备.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、May 2012 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 13

2、.300; 23.020.20; 23.040.60!$|06“1891319www.din.deDDIN EN 13081Tanks for transport of dangerous goods Service equipment for tanks Vapour collection adaptor and coupler (includes Amendment A1:2012)English translation of DIN EN 13081:2012-05Tanks fr die Befrderung gefhrlicher Gter Bedienungsausrstung v

3、on Tanks VKG- und MKG-Kupplungen fr die Gassammelleitung (enthlt nderung A1:2012)Englische bersetzung von DIN EN 13081:2012-05Citernes de transport de matires dangereuses quipement de service pour citernes Adaptateur et coupleur pour la rcupration des vapeurs (Amendement A1:2012 inclus)Traduction an

4、glaise de DIN EN 13081:2012-05SupersedesDIN EN 13081:2009-02www.beuth.deDocument comprises 20 pagesIn case of doubt, the German-language original shall be considered authoritative.04.12 DIN EN 13081:2012-05 2 A comma is used as the decimal marker. National foreword This standard has been prepared by

5、 Technical Committee CEN/TC 296 “Tanks for transport of dangerous goods” (Secretariat: AFNOR, France), Working Group WG 7 “Service equipment (including equipment for vapour recovery, bottom loading, confinement and handling of petroleum products” (Secretariat: BSI, United Kingdom). The responsible G

6、erman body involved in its preparation was the Normenausschuss Tankanlagen (Tank Installations Standards Committee), Working Committee NA 104-02-07 AA Ausrstungen fr Transporttanks. Amendments This standard differs from DIN EN 13081:2009-02 as follows: a) in Subclause 3.2 a definition for the term “

7、probe” has been added; b) in Annex A (normative) specifications for the opening of the vapour collection adaptor have been added; c) in Annex B (normative) specifications for the opening of the vapour collection coupler have been added; d) in Annex C (normative) specifications for the interlock have

8、 been added. Previous editions DIN EN 13081: 2001-07, 2009-02 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13081:2008+A1 February 2012 ICS 23.040.60; 13.300; 23.020.20 Supersedes EN 13081:2008English Version Tanks for transport of dangerous goods - Service equipment for tanks - Vapour collec

9、tion adaptor and coupler Citernes de transport de matires dangereuses - Equipement de service pour citernes - Adaptateur et coupleur pour la rcupration des vapeurs Tanks fr die Befrderung gefhrlicher Gter - Bedienungsausrstung von Tanks - VKG- und MKG-Kupplungen fr die Gassammelleitung This European

10、 Standard was approved by CEN on 13 September 2008 and includes Amendment 1 approved by CEN on 24 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any al

11、teration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language m

12、ade by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Est

13、onia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISA

14、TION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13081:2008+A1:2012: EEN 13081:2008+A1:2012 (E) 2 Contents Page Foreword 3Introduction .51

15、 Scope 62 Normative references 63 Terms and definitions .64 Function 75 Design characteristics 75.1 General 75.2 Performance characteristics 75.3 Pressure ratings.75.4 Temperature range 75.5 Materials of construction 75.6 Dimensional characteristics .86 Tests 86.1 General 86.2 Production tests.86.2.

16、1 General 86.2.2 Shell tightness test 96.2.3 Internal seat tightness test .96.2.4 Operability test .96.2.5 Test results .96.3 Type tests .96.3.1 General 96.3.2 Shell strength test. 106.3.3 Shell tightness test . 106.3.4 Internal seat tightness test 106.3.5 Mechanical endurance test 106.3.6 Mechanica

17、l strength test 106.3.7 Test results 117 Marking 118 Installation, operation and maintenance instructions 11Annex A (normative) Vapour collection adaptor to be fitted on the transport tank 12Annex B (normative) Vapour collection coupler to be fitted to the stationary loading and unloading facility 1

18、4Annex C (normative) Interlock and other devices . 15C.1 Interlock . 15C.2 DTQM tank identifier . 16Annex D (informative) 4 hole fixing 17Bibliography . 18DIN EN 13081:2012-05 EN 13081:2008+A1:2012 (E) 3 Foreword This document (EN 13081:2008+A1:2012) has been prepared by Technical Committee CEN/TC 2

19、96 “Tanks for transport of dangerous goods”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2012, and conflicting national standards shall be wit

20、hdrawn at the latest by August 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes !EN 13081:2008“. This do

21、cument includes Amendment 1 approved by CEN on 2011-12-24. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. !Compared to EN 13081:2008 the following changes have been made: a) in 3.2 a definition for “probe“ has been added; b) in Annex A (normative

22、) specifications for the opening of the adaptor have been added; c) in Annex B (normative) specifications for the opening of the coupler have been added; d) in Annex C (normative) specifications for the interlock have been added.“ This European standard forms part of a coherent standards programme c

23、omprising the following standards, under the general title “Tanks for transport of dangerous goods - Service equipment for tanks“ EN 13081, Vapour collection adaptor and coupler EN 13082, Vapour transfer valve EN 13083, Adaptor for bottom loading and unloading EN 13308, Non pressure balanced footval

24、ve EN 13314, Fill hole cover EN 13315, Gravity discharge coupler EN 13316, Pressure balanced footvalve EN 13317, Manhole cover assembly EN 13922, Overfill prevention systems for liquid fuels EN 14595, Pressure and Vacuum Breather Vent EN 14596, Emergency pressure relief valve EN 15208, Sealed parcel

25、 delivery systems Working principles and interface specifications DIN EN 13081:2012-05 EN 13081:2008+A1:2012 (E) 4 The standards programme also includes the following Technical Report: CEN/TR 15120, Tanks for transport of dangerous goods - Guidance and recommendations for loading, transport and unlo

26、ading. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

27、Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13081:2012-05 EN 13081:2008+A1:2012 (E) 5 Introduction The vapour collection adaptor and coupler are part of the

28、 vapour collection system that is required to comply with the European Directive 94/63/EC on Volatile Organic Compounds (VOC) 1. The vapour collection adaptor and coupler establish a vapour tight path between the transport tank and the stationary loading and unloading facilities. DIN EN 13081:2012-0

29、5 EN 13081:2008+A1:2012 (E) 6 1 Scope This European Standard covers the vapour collection adaptor and coupler used to achieve a vapour tight path between the transport tank and the stationary loading and unloading facilities. This European Standard specifies the performance requirements and the crit

30、ical dimensions of the vapour recovery adaptor fitted to the tank and the mating coupler fitted to a hose or to pipework connected to the stationary loading and unloading facilities. It also specifies the tests necessary to verify the compliance of the equipment with this standard. The equipment spe

31、cified by this European Standard is suitable for use with liquid petroleum products and other dangerous substances of Class 3 of ADR 2 which have a vapour pressure not exceeding 110 kPa, at 50 C and petrol, and which have no sub-classification as toxic or corrosive. 2 Normative references The follow

32、ing referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document (including amendments) applies. EN 12266-1:2003, Industrial valves Testing of valves Part 1: Pres

33、sure tests, test procedures and acceptance criteria Mandatory requirements EN 12266-2:2002, Industrial valves Testing of valves Part 2: Tests, test procedures and acceptance criteria Supplementary requirements EN 15208:2007, Tanks for transport of dangerous goods - Sealed parcel delivery systems Wor

34、king principles and interface specifications EN ISO 1302, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation (ISO 1302:2002) EN ISO 4287, Geometrical Product Specifications (GPS) Surface texture: Profile method Terms, definitions and surface tex

35、ture parameters (ISO 4287:1997) ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 Maximum

36、Working Pressure (MWP) gauge pressure maximum pressure to which the equipment is designed to operate, being the highest of the following three pressures: a) highest effective pressure allowed in the tank during filling (maximum filling pressure allowed) b) highest effective pressure allowed in the t

37、ank during discharge (maximum discharge pressure allowed) c) effective gauge pressure to which the tank is subjected by its contents (including such extraneous gases as it may contain) at the maximum working temperature DIN EN 13081:2012-05 EN 13081:2008+A1:2012 (E) 7 !3.2 probe device used to displ

38、ace the obturator (poppet) of the adaptor“ 4 Function The vapour collection adaptor and coupler shall provide the following: a quick action vapour tight mechanical connection between the transport tank and the stationary loading and unloading facilities for the transfer of vapour; vapour tightness w

39、hen not connected. The vapour collection adaptor may be capable of accepting interlock actuators and similar devices, see Annex C. The vapour collection adaptor may have provision for a sight glass to check for the presence of liquid. The vapour collection adaptor may have provision for the drainage

40、 of liquid. 5 Design characteristics 5.1 General The vapour collection adaptor and coupler shall permit the transfer of vapour only after initiation of the mating action. 5.2 Performance characteristics The manufacturer shall provide the pressure drop curves for both the vapour collection adaptor an

41、d coupler at the following conditions: flow rate up to 1 500 standard m3/h of air at 20 C (1 500 standard m3/h of air corresponds to the bottom loading of 5 compartments simultaneously each at 150 m3/h flow of substances). 5.3 Pressure ratings The vapour collection adaptor shall be capable of operat

42、ing at the MWP of the transport tank to which it is attached. The vapour collection coupler shall be capable of operating at the MWP of the stationary loading and unloading facility to which it is attached. 5.4 Temperature range Unless otherwise specified, the design temperature range shall be 20 C

43、to + 50 C. Where the vapour collection adaptor and coupler are subjected to more severe conditions, the design temperature range shall be extended to 40 C or + 70 C as applicable. 5.5 Materials of construction The manufacturer shall provide with the equipment a full material specification for those

44、parts that may come into contact with the substances described by Clause 1. DIN EN 13081:2012-05 EN 13081:2008+A1:2012 (E) 8 5.6 Dimensional characteristics The dimensions, tolerances and surface machined finish of the vapour collection adaptor and coupler shall be as given in Annexes A and B (see F

45、igures A.1 and B.1). The mounting dimensions of the flange connecting the vapour collection adaptor to the pipework of the tank shall be as follows: outside diameter (maximum) : 174 mm; inside diameter (minimum) : 100 mm; pitch circle diameter : 150 mm; number of holes : 8 equispaced; hole diameter

46、: 14 mm. NOTE 1 Tolerances 1 mm. NOTE 2 Holes should straddle adaptor centre line. NOTE 3 A 4 hole mounting, which can accommodate the specified 8 hole flange without loss of performance may be used as an option, see Annex D. 6 Tests 6.1 General Two classes of tests are required: production tests an

47、d type tests. Testing methods and procedures shall conform to EN 12266-1 and EN 12266-2 except as specified within this European Standard. Unless otherwise specified, test fluids shall be air or other suitable gas. The choice of the fluid is the responsibility of the manufacturer. NOTE Where the obt

48、urator forms part of the pressure containing shell, it may be closed during strength and tightness tests. 6.2 Production tests 6.2.1 General The number, frequency and sampling methods of production test samples shall not be less than those specified within ISO 2859-1 (AQL of 2,5). Production tests shall comprise the following: shell tightne