DIN EN 1301-1-2008 Aluminium and aluminium alloys - Drawn wire - Part 1 Technical conditions for inspection and delivery English version of DIN EN 1301-1 2008-12《铝和铝合金 拉制钢丝 第1部分 检验.pdf

《DIN EN 1301-1-2008 Aluminium and aluminium alloys - Drawn wire - Part 1 Technical conditions for inspection and delivery English version of DIN EN 1301-1 2008-12《铝和铝合金 拉制钢丝 第1部分 检验.pdf》由会员分享，可在线阅读，更多相关《DIN EN 1301-1-2008 Aluminium and aluminium alloys - Drawn wire - Part 1 Technical conditions for inspection and delivery English version of DIN EN 1301-1 2008-12《铝和铝合金 拉制钢丝 第1部分 检验.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、December 2008DEUTSCHE NORM English price group 8No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.150.10!$Tz“1498795w

2、ww.din.deDDIN EN 1301-1Aluminium and aluminium alloys Drawn wire Part 1: Technical conditions for inspection and deliveryEnglish version of DIN EN 1301-1:2008-12Aluminium und Aluminiumlegierungen Gezogene Drhte Teil 1: Technische LieferbedingungenEnglische Fassung DIN EN 1301-1:2008-12SupersedesDIN

3、EN 1301-1:1997-11www.beuth.deDocument comprises 12 pagesDIN EN 1301-1:2008-12 2 National foreword This standard has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” (Secretariat: AFNOR, France), Working Group WG 4 “Wires and drawing stock”. The responsible German body

4、 involved in its preparation was the Normenausschuss Nichteisenmetalle (Nonferrous Metals Standards Committee), Technical Committee NA 066-01-03 AA Draht und Vordraht. Amendments This standard differs from DIN EN 1301-1:1997-11 as follows: a) The foreword has been modified. b) Clause 2: EN 12258-1:1

5、998 and EN 14361 have been added. c) Clause 3: Subclauses 3.1 to 3.9 have been deleted and are replaced by reference to EN 12258-1:1998. d) Clause 6: Subclauses 6.1.2 and 6.1.3 have been modified. e) Clause 7: completely revised. Previous editions DIN 1747-2: 1968-12, 1977-05, 1983-02 DIN 1790-2: 19

6、77-05 DIN EN 1301-1: 1997-11 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1301-1September 2008ICS 77.150.10 Supersedes EN 1301-1:1997 English VersionAluminium and aluminium alloys - Drawn wire - Part 1: Technicalconditions for inspection and deliveryConditions techniques de contrle et de livrai

7、sonAluminium und Aluminiumlegierungen - Gezogene Drhte -Teil 1: Technische LieferbedingungenThis European Standard was approved by CEN on 16 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the statu

8、s of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A ve

9、rsion in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den

10、mark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIO

11、NEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1301-1:2008: EAluminium et alliages daluminium - Fil tir - Partie 1:EN 1301-1:2008 (E) 2 Conte

12、nts Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Ordering information.4 5 Requirements.5 5.1 Production and manufacturing processes .5 5.2 Quality control5 5.3 Chemical composition 5 5.4 Mechanical properties.6 5.5 Freedom from defects .6 5.6 Tolerances on dimension

13、s .6 5.7 Other properties.6 5.8 Temper of delivery.6 6 Test procedure.6 6.1 Sampling.6 6.2 Methods of tests 7 6.3 Retests 8 7 Delivery documents and inspection documents8 7.1 Certificate of mass and analysis8 7.2 Inspection certificate.9 8 Marking .9 9 Packaging .9 10 Complaints of non-conformity .9

14、 Bibliography 10 DIN EN 1301-1:2008-12 EN 1301-1:2008 (E) 3 Foreword This document (EN 1301-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard

15、, either by publication of an identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at the latest by March 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN an

16、d/or CENELEC shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions, then this product shall be re

17、moved from the corresponding standard. This document supersedes EN 1301-1:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 “Wires and drawing stock“ to revise EN 1301-1:1997. Besides editorial adjustments in the text and update of normative references the

18、following changes have been made: Foreword : amended; Clause 2: EN 12258-1:1998 and EN 14361 added; Clause 3: subclauses 3.1 to 3.9 deleted and replaced by reference to EN 12258-1:1998; Clause 6: subclauses 6.1.2 and 6.1.3 modified; Clause 7: completely revised. EN 1301 comprises the following parts

19、 under the general title: “Aluminium and aluminium alloys Drawn wire“: Part 1: Technical conditions for inspection and delivery Part 2 : Mechanical properties Part 3 : Tolerances on dimensions According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following co

20、untries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S

21、pain, Sweden, Switzerland and the United Kingdom. DIN EN 1301-1:2008-12 EN 1301-1:2008 (E) 4 1 Scope This document specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy drawn wire for general engineering applications. It does not apply for aeronautical appli

22、cation. It applies to drawn wires, except for electrical or welding purposes. It does not apply to drawing stock. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refere

23、nces, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of prod

24、ucts EN 1301-2, Aluminium and aluminium alloys Drawn wire Part 2: Mechanical properties EN 1301-3, Aluminium and aluminium alloys Drawn wire Part 3: Tolerances on dimensions EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature EN 10204, Metallic products Types

25、 of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 14361, Aluminium and aluminium alloys Chemical analysis Sampling from metal melts 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1

26、2258-1:1998 apply. 4 Ordering information The order shall define the product required and shall contain the following information: a) form and type of product: 1) form of the product (round wire, rectangular wire, etc.); 2) designation of the aluminium or aluminium alloy in accordance with EN 573-3;

27、 b) temper of the material for delivery (degree of hardness or heat-treatment condition), and, if different, the temper of use in accordance with EN 515; c) number of this European Standard or a specification number or, otherwise, the properties agreed between manufacturer and purchaser; DIN EN 1301

28、-1:2008-12 EN 1301-1:2008 (E) 5 d) dimensions and shape of the product: 1) diameter; 2) thickness and width for rectangular wires; 3) reference to a drawing if necessary; e) tolerances on the dimensions, in accordance with EN 1301-3; f) quantity: 1) mass or length; 2) tolerances on quantity if requi

29、red; g) any requirements for certificates of conformity, test and/or analysis reports or inspection certificates; h) any special requirements agreed between manufacturer and purchaser: 1) testing procedure; 2) marking of products; 3) surface quality; 4) type of conditioning, packaging, etc. 5 Requir

30、ements 5.1 Production and manufacturing processes Unless otherwise specified in the order, the production and manufacturing processes shall be left to the discretion of the manufacturer. Unless it is explicitly stated in the order, no obligation shall be placed on the manufacturer to use the same pr

31、ocesses for subsequent and similar orders. 5.2 Quality control The manufacturer shall be responsible for the performance of all inspection and tests, prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall notify the manufacturer at the t

32、ime of placing the order. 5.3 Chemical composition The chemical composition shall conform to EN 573-3. If the purchaser requires tighter content limits of the specified elements or content limits for elements not specified in EN 573-3, these limits shall be stated on the order, after agreement betwe

33、en the supplier and the purchaser. DIN EN 1301-1:2008-12 EN 1301-1:2008 (E) 6 5.4 Mechanical properties The mechanical properties shall conform to EN 1301-2 or to those agreed upon between manufacturer and purchaser and stated on the order. 5.5 Freedom from defects The products shall be free from de

34、fects prejudicial to its suitable and proper use. Whilst an operation designed to mask a fault is not permitted, the elimination of a superficial imperfection is permissible, provided that the tolerances on dimensions and the material properties continue to meet specifications. 5.6 Tolerances on dim

35、ensions The tolerances on dimensions shall conform to EN 1301-3. 5.7 Other properties Additional property requirements, such as bending, torsion, wrapping and heading ability and shearing strength, etc., shall be agreed by the manufacturer and purchaser, and stated on the order. 5.8 Temper of delive

36、ry The variety of aluminium and aluminium alloys used required a precise definition of the temper of delivery which is liable to exert a significant influence on the ability to process and on the final characteristics of the wires manufactured. Tempers shall be in accordance with EN 515. The usual t

37、empers for drawn wires covered by this standard are: O: as annealed; H: strain hardened; T: thermally treated. 6 Test procedure 6.1 Sampling 6.1.1 Chemical analysis Samples for chemical analysis shall be taken at the time of casting according to EN 14361. Their shape and conditions of production (mo

38、uld design, cooling rate, mass, etc.) shall be designed, such that they represent the average composition of the liquid metal, and be suitable for the method of analysis. The analytical procedure shall be taken into account. 6.1.2 Test pieces for mechanical testing 6.1.2.1 Identification of test pie

39、ces Each test pieces shall be marked in such a manner that, after removal, it is always possible to identify the product from which it is taken and its location. If, during the course of subsequent operations, removal of the markings cannot be avoided, new markings or labels shall be made before the

40、 originals are removed. DIN EN 1301-1:2008-12 EN 1301-1:2008 (E) 7 6.1.2.2 Preparation of test pieces Test pieces shall be taken from the sample after completion of all the mechanical and heat-treatments that the product has to undergo before delivery, and which can influence the mechanical properti

41、es of the metal. In cases where this is not possible, the test pieces can be taken at an earlier stage, but they shall be subjected to the same treatment as that to which it is intended to submit the product concerned1). Cutting shall be carried out in such a manner that it does not change the chara

42、cteristics of the part of the sample from which the test pieces are to be prepared. Thus, the dimensions of the samples shall provide an adequate machining allowance to permit removal of the zone affected by cutting. Samples shall not be machined or treated in any way by which their mechanical prope

43、rties can be altered. Any straightening required shall be carried out with great care, preferably by hand. 6.1.3 Test-pieces for tensile test 6.1.3.1 Identification of test pieces Each test piece shall be marked in such manner so that it is possible to identify the inspection lot from which it was t

44、aken. If a test piece is marked by stamping, this shall not be in a place or manner which can interfere with subsequent testing. NOTE Where it is not convenient to mark a test piece, an identification label can be attached. 6.1.3.2 Number of test pieces One test piece shall be taken from each sample

45、. 6.1.3.3 Type and location of test pieces The un-machined wire shall be considered as the test piece. 6.2 Methods of tests 6.2.1 Chemical composition Methods of analysis shall be at the discretion of the manufacturer. In case of dispute concerning the chemical composition, referee analysis shall be

46、 carried out by the methods specified in the relevant European Standard (see EN 14242 and EN 14726) and the results obtained by this method shall be accepted. 6.2.2 Tensile test The tensile test shall be carried out in accordance with EN 10002-1. 6.2.3 Measurement of dimensions All dimensions shall

47、be checked at the ambient temperature of the workshop or laboratory, and in case of dispute, at a temperature between 15 C and 25 C. 1)If the purchaser intends to convert the material to a final temper which is different from the “as supplied“ temper, then additional testing may be requested by the

48、purchaser in order to be satisfied that the material is capable of meeting the specified properties of the final temper. It is only necessary for the supplier to confirm that selected samples, heat-treated using supplier laboratory conditions, meet the properties specified for the final temper requi

49、red by the purchaser. DIN EN 1301-1:2008-12 EN 1301-1:2008 (E) 8 6.2.4 Surface finish Unless otherwise specified, examination of surface appearance shall be carried out before delivery without the assistance of magnifying apparatus. 6.2.5 Other tests If other mechanical or physical tests are required, these shall be agreed between manufacturer and purchaser. These tests shall be carried out either in accordance with the existing European or International Standards (for example EN ISO 6507-1, EN ISO 7438, ISO 78