DIN EN 10264-3-2012 Steel wire and wire products - Steel wire for ropes - Part 3 Round and shaped non alloyed steel wire for high duty applications German version EN 10264-3 2012《钢.pdf

《DIN EN 10264-3-2012 Steel wire and wire products - Steel wire for ropes - Part 3 Round and shaped non alloyed steel wire for high duty applications German version EN 10264-3 2012《钢.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10264-3-2012 Steel wire and wire products - Steel wire for ropes - Part 3 Round and shaped non alloyed steel wire for high duty applications German version EN 10264-3 2012《钢.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、March 2012 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、77.140.65!$zU“1875094www.din.deDDIN EN 10264-3Steel wire and wire products Steel wire for ropes Part 3: Round and shaped non alloyed steel wire for high dutyapplicationsEnglish translation of DIN EN 10264-3:2012-03Stahldraht und Drahterzeugnisse Stahldraht fr Seile Teil 3: Runder und profilierter Dr

3、aht aus unlegiertem Stahl fr hohe BeanspruchungenEnglische bersetzung von DIN EN 10264-3:2012-03Fils et produits trfils en acier Fils pour cbles Partie 3: Fils ronds et profils, en acier non alli, pour fortes sollicitationsTraduction anglaise de DIN EN 10264-3:2012-03SupersedesDIN EN 10264-3:2003-02

4、www.beuth.deDocument comprises 17 pagesIn case of doubt, the German-language original shall be considered authoritative.03.12 DIN EN 10264-3:2012-03 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires” (Se

5、cretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Stahldraht und Stahldraht-erzeugnisse (Steel Wire and Wire Products Standards Committee), Working Committee NA 099-00-01 AA Stahldraht. Amendments This standard differs from DIN EN 10264-3:2003

6、-02 as follows: a) the scope of the standard has been revised; b) normative references have been updated; c) purity of the zinc coating of the drawn wire in accordance with EN 1179 has been specified (see Clause 4); d) the values of the Z and H profiles have been updated; e) the values given in Tabl

7、es 4 and 5 have been updated; f) a second quality of zinc coating has been added (see 5.3.4); g) in Table 11 three additional ranges for nominal dimensions of round wire have been added; h) the standard has been editorially revised. Previous editions DIN 779: 1969-04, 1980-12 DIN 3078: 1982-05, 1990

8、-05 DIN EN 10264-3: 2003-02 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10264-3 January 2012 ICS 77.140.65 Supersedes EN 10264-3:2002English Version Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications Fils et produ

9、its trfils en acier - Fils pour cbles - Partie 3: Fils ronds et profils, en acier non aill, pour fortes sollicitations Stahldraht und Drahterzeugnisse - Stahldraht fr Seile - Teil 3: Runder und profilierter Draht aus unlegiertem Stahl fr hohe Beanspruchungen This European Standard was approved by CE

10、N on 19 November 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standar

11、ds may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and noti

12、fied to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuani

13、a, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national M

14、embers. Ref. No. EN 10264-3:2012: EEUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG EN 10264-3:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Designation of the product .54 General conditions of manufacture .55 Characteristic

15、s of the wire 55.1 Tensile strength grades 55.2 Profiles 65.2.1 Definition of shaped wire 65.2.2 Equivalent diameter .85.3 Minimum requirements for wire characteristics .85.3.1 Dimension measured values .85.3.2 Reverse bend test 95.3.3 Torsion test . 125.3.4 Zinc and Zn95/Al5 coatings . 146 Test met

16、hods . 156.1 General . 156.2 Reverse bend test . 15DIN EN 10264-3:2012-03 EN 10264-3:2012 (E) 3 Foreword This document (EN 10264-3:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the st

17、atus of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject

18、 of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10264-3:2002. This European Standard for wire for ropes is made up of the following parts: Part 1: General requirements Part 2: Cold drawn non alloy steel wi

19、re for ropes for general applications Part 3: Round and shaped non alloyed steel wire for high duty applications Part 4: Stainless steel wire This European Standard has been technically revised to incorporate the following changes: a) heavy duty applications have been explained in the new last sente

20、nce of the scope; b) the purity of the zinc coating of the drawn wire has been specified according the relevant EN 1179 (see Clause 4); c) a footnote c) has been added in Table 1 in order to precise the meaning of coated; d) the values of the Z and H profiles have been updated in Table 2; e) a note

21、has been added to allow other wire diameters higher than those given in Table 3 “Dimensional tolerances on round wire diameter“ subject to an agreement between supplier and user at the time of order; f) modifications have been made on values concerning “Coated Class A“ given in Table 4 “Dimensional

22、tolerances for shaped wire“; g) modifications have been made in Table 5 “Minimum number of reverse bends for shaped wire for static applications“ concerning the values of Z profile for the height of profile upper to 5 mm; h) a second quality of zinc coating has been added for dynamic applications (s

23、ee 5.3.4); i) three additional ranges for Nominal dimensions of round wire (from 0,50 mm to 0,80 mm) have been added (see Table 11 “Minimum mass of coating“). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement thi

24、s European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

25、, Turkey and the United Kingdom. DIN EN 10264-3:2012-03 EN 10264-3:2012 (E) 4 1 Scope This part of this European Standard specifies round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and ot

26、her high duty applications. Heavy duty refers to situations where the stresses applied to the rope are either high or vary by a large amount during service. This part of this European Standard refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T). In

27、addition to the requirements of this part of this European Standard, the requirements of EN 10264-1 also apply. It does not apply to steel wire taken from manufactured ropes. This part of this European Standard specifies the following for cold drawn non alloyed steel wire for ropes for high duty app

28、lications: dimensional tolerances; mechanical characteristics; requirements relating to the chemical composition of the steel wire; conditions to be satisfied by any coating. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated r

29、eferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1179, Zinc and zinc alloys Primary zinc EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10244-2, Steel wire and wire produc

30、ts Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings EN 10264-1:2011, Steel wire and wire products Steel wire for ropes Part 1: General requirements EN ISO 16120-1:2011, Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1:2011) EN

31、 ISO 16120-2:2011, Non-alloy steel wire rod for conversion to wire - Part 2: Specific requirements for general-purpose wire rod (ISO 16120-2:2011) EN ISO 16120-4:2011, Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4:2

32、011) DIN EN 10264-3:2012-03 EN 10264-3:2012 (E) 5 3 Designation of the product The designation of wire for ropes manufactured in accordance with this European Standard shall be based on the nominal dimension, surface appearance and tensile strength. The indicator of dimension for round wire is the n

33、ominal diameter; for shaped wire it is the value of the height (h), followed by a letter specifying the profile. In the case of H profiles, this indicator shall be followed by the value of the narrowing. The surface appearance shall be indicated as defined in EN 10264-1 with U for uncoated or bright

34、 wire, with a letter indicating the class of coating (A, B, ) and in the case of zinc alloy coatings, indicating in brackets (Zn/Al). EXAMPLE 1 2,0 mm wire for rope with thick zinc layer, class A, tensile strength grade 1 570 MPa, in accordance with EN 10264-3. Designation: wire for rope EN 10264-3

35、2,0 - A 1 570 EXAMPLE 2 Wire for rope, trapezoidal profile, h = 3,5 mm, class B zinc coated, tensile strength grade 1 770 MPa, in accordance with EN 10264-3. Designation: wire for rope EN 10264-3 - T3,5 - B 1 770 EXAMPLE 3 H shaped wire for rope h = 3,0 mm, w = 1,8 mm, coated with class A zinc alloy

36、, tensile strength grade 1 370 MPa, in accordance with EN 10264-3. Designation: wire for rope EN 10264-3 - H 3,0 1,8 - A (Zn/Al) 1 370 4 General conditions of manufacture The drawn wire shall be manufactured from rod in accordance with EN ISO 16120-1 and EN ISO 16120-2 for ropes for static applicati

37、ons, and in accordance with EN ISO 16120-1 and EN ISO 16120-4 for ropes for dynamic applications. The drawn wire shall show no surface defects or internal defects prejudicial to its use. When specified, the drawn wire shall be supplied with a coating applied by a hot dipping or electrolytic method.

38、The coatings commonly used are zinc or Zn95/Al5. Unless otherwise specified, the zinc used for coating shall have a purity of 99,95 % according to EN 1179, Z3, other zinc alloys may be agreed at the time of enquiry and order. NOTE If required by the purchaser, the quality of the zinc or zinc alloy u

39、sed for the coating material (zinc or zinc alloy) should be certified by the manufacturer. Because of the reaction between the base material and coating material, which is inherent to the process, the composition of the coating on the wire is different to that used in the coating bath. 5 Characteris

40、tics of the wire 5.1 Tensile strength grades The tensile strength grades are defined in Table 1. NOTE The nominal values are the minimum tensile strength limits. The upper limits (maximum) are equal to these minimum values increased with the tolerances specified in EN 10264-1:2011, Table 1. DIN EN 1

41、0264-3:2012-03 EN 10264-3:2012 (E) 6 Table 1 Tensile strength grade Quality of wire cNominal tensile strength grade MPa aRound Bright or coated Class B 1 570 1 770 1 960 2 160 Zinc or Zn95/Al5 - Class A 1 570 1 770 Shaped Bright or coated Class B 1 370 1 570 1 770 or class D b1 270 1 370 1 470 1 570

42、 1 670 1 770 Zinc or Zn95/Al5 - Class A 1 370 1 570 NOTE Subject to agreement between the manufacturer and the purchaser, other tensile strength grades can be used.a1 MPa = 1 N/mm2. bMass of coatings for static and dynamic applications are specified in Table 11. cCoated means zinc or Zn95/Al5 alloy.

43、 5.2 Profiles 5.2.1 Definition of shaped wire For shaped wire, the characteristic sections of the wire are shown in Figure 1 for full lock Z, half lock H and trapezoidal T wires. The nominal dimensions and tolerances shall be agreed between the supplier and the purchaser at the time of ordering. The

44、 conventional characteristic values are as follows: h height: difference between the radii of the 2 concentric boundary circles; b width: maximum width of upper part perpendicular to a radial line passing through the centre of the width (as shown in Figure 1); w minimum narrowing: smallest width of

45、the profile; e distance taken diagonally across the transverse section of the profile (essentially T or Z profiles). The designation of a full lock wire is established using the letter Z and the height (h), that of a half lock wire by H followed by the height (h) and the minimum narrowing (w) (h w)

46、and that of a trapezoidal wire by the letter T followed by the height (h). Table 2 gives the design criteria for the shaped wire shown in Figure 1. These are the relation between the height of the shaped wires and the other major characteristic dimensions. DIN EN 10264-3:2012-03 EN 10264-3:2012 (E)

47、7 Figure 1 Shaped wire sections Table 2 Design criteria for shaped wire Ratio Z profile H profile Trapezoidal profile T h : b 0,9 to 1,55 - 1,0 to 1,3 h : e 0,55 to 0,80 - 0,75 to 0,90 h : w - 0,8 to 2,3 DIN EN 10264-3:2012-03 EN 10264-3:2012 (E) 8 5.2.2 Equivalent diameter The definition of the equ

48、ivalent diameter of shaped wire is as follows. The diameter of the equivalent transverse circular section (a) is the diameter of a circle with the same transverse section surface area as the shaped wire. The diameter of the equivalent circular circumference (c) is the diameter of the circle with the same perimeter as the shaped wire. Nominal values may be measured by planimetry on the drawing of the shap