DIN EN 10218-2-2012 Steel wire and wire products - General - Part 2 Wire dimensions and tolerances German version EN 10218-2 2012《钢丝和线材产品 总则 第2部分 线材尺寸和公差》.pdf

《DIN EN 10218-2-2012 Steel wire and wire products - General - Part 2 Wire dimensions and tolerances German version EN 10218-2 2012《钢丝和线材产品 总则 第2部分 线材尺寸和公差》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 10218-2-2012 Steel wire and wire products - General - Part 2 Wire dimensions and tolerances German version EN 10218-2 2012《钢丝和线材产品 总则 第2部分 线材尺寸和公差》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、March 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 7

2、7.140.65!$z?s“1872880www.din.deDDIN EN 10218-2Steel wire and wire products General Part 2: Wire dimensions and tolerancesEnglish translation of DIN EN 10218-2:2012-03Stahldraht und Drahterzeugnisse Allgemeines Teil 2: Drahtmae und ToleranzenEnglische bersetzung von DIN EN 10218-2:2012-03Fils et prod

3、uits trfils en acier Gnralits Partie 2: Dimensions et tolrances des filsTraduction anglaise de DIN EN 10218-2:2012-03SupersedesDIN EN 10218-2:1996-08www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 11 pages02.12 DIN EN 10218-2:2012-03 2

4、A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Eisen und Stahl (Iron and Steel Standards Co

5、mmittee), Working Committee NA 021-00-08-04 UA Patentiert-gezogener oder vergteter Federstahldraht. Amendments This standard differs from DIN EN 10218-2:1996-08 as follows: a) normative references have been updated; b) new notes relating to the definition of wire have been added to 3.1; c) Clause 4

6、“Wire diameter tolerance” has been split into 4.1 “Tolerance on diameter of uncoated and metallic coated round steel wire” and 4.2 “Tolerances on diameter of organic coated wire”, and new figures have been added; d) Table 2 “Tolerances on diameter and coating thickness of sintered and extruded organ

7、ic coated wire” has been revised; e) Table 5 “Straightness test lengths” has been revised; f) the key to Figure 3 has been revised; g) the standard has been editorially revised. Previous editions DIN 177: 1923-10, 1927-10, 1934-09, 1967-05, 1971-03, 1988-11 DIN 2076: 1944x-02, 1964-03, 1984-12 DIN 3

8、036-1: 1978-03 DIN 3036-2: 1978-03 DIN EN 10218-2: 1996-08 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10218-2 January 2012 ICS 77.140.65 Supersedes EN 10218-2:1996English Version Steel wire and wire products - General - Part 2: Wire dimensions and tolerances Fils et produits trfils en acie

9、r - Gnralits - Partie 2: Dimensions et tolrances des fils Stahldraht und Drahterzeugnisse - Allgemeines - Teil 2: Drahtmae und Toleranzen This European Standard was approved by CEN on 3 September 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the cond

10、itions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exist

11、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national stan

12、dards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur

13、key and United Kingdom. Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10218-2:2012: EEUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMI

14、TEE FR NORMUNG EN 10218-2:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Wire diameter tolerance 54.1 Tolerance on diameter of uncoated and metallic coated round steel wire .54.1.1 General 54.1.2 Out of roundness (ovality) 64.2 Tolerances on diameter

15、of organic coated wire .74.2.1 General 74.2.2 Extruded organic coating .74.2.3 Sintered organic coating .75 Tolerance on cut lengths 85.1 Tolerance on length .85.2 Tolerance and straightness 96 Length of wire in coil .9DIN EN 10218-2:2012-03 EN 10218-2:2012 (E) 3 Foreword This document (EN 10218-2:2

16、012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicti

17、ng national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document sup

18、ersedes EN 10218-2:1996. The standard will comprise the following parts: Part 1: Test methods; Part 2: Wire dimensions and tolerances. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Aus

19、tria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

20、Kingdom. DIN EN 10218-2:2012-03 EN 10218-2:2012 (E) 4 1 Scope This European Standard specifies the tolerances on diameter of round wire and, where applicable, on the length of round wire cut to length, for bright steel wire, (i.e. uncoated), metallic coated steel wire and non-metallic coated steel w

21、ire. This European Standard should not be applied where other requirements for dimensions and tolerances are specified in a particular product standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the ed

22、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10079:2007, Definition of steel products 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 wire product of constan

23、t full cross section along its length, obtained by cold drawing rod through a reducing die or passing under pressure between rollers and rewinding the drawn product NOTE 1 The cross section is generally round, though sometimes oval, rectangular, square, hexagonal, octagonal or other convex section.

24、NOTE 2 The manufacturing processes give close control of geometric (size, surface condition) and mechanical properties. Wire may be supplied uncoated (as drawn, annealed) or coated (e.g. with zinc, copper, nickel or plastic materials). NOTE 3 Heat treatments and/or surface treatments may be carried

25、out during the course of manufacture to improve the properties of wire. EN 10079:2007 NOTE 4 As well as being supplied in the uncoated (bright) condition, wire can also be supplied with metallic or non-metallic coatings or both.The metallic coating can be as a finished coating or as a drawn finished

26、 coating. 3.2 cut length straightened piece of wire cut to a specified length DIN EN 10218-2:2012-03 EN 10218-2:2012 (E) 5 4 Wire diameter tolerance 4.1 Tolerance on diameter of uncoated and metallic coated round steel wire 4.1.1 General Key 1 metallic coating thickness in mm d overall diameter in m

27、m (including, where existing, the metallic coating) Figure 1 For Table 1 Diameter measurements shall be made at any cross-section and shall not differ from the tolerances specified in the relevant tables in this standard. NOTE 1 Diameter tolerances may vary when cut lengths are supplied by a third p

28、arty. NOTE 2 Diameter tolerances are calculated as follows: T1 = 0,035 d T2 = 0,027 d T3 = 0,021 d T4 = 0,015 d T5 = 0,010 d where d is the overall diameter measured in mm (including, where existing, the metallic coating) The purchaser or the product standard shall indicate the tolerance range requi

29、red from Table 1. The overall diameter shall be within the relevant tolerance range given in Table 1; the producer will adapt processing parameters to ensure compliance with the required properties of the wire in the respective product standard, taking into account the influence of the coating thick

30、ness (if applicable). NOTE 3 Unless otherwise specified on the order/enquiry or the product standard, tolerances class T1 would generally be used for heavy galvanised (A) wire, T2 would generally be used for other galvanised wire, and T3, T4 and T5 would generally be used for bright drawn wire in in

31、creasing order of precision required. DIN EN 10218-2:2012-03 EN 10218-2:2012 (E) 6 4.1.2 Out of roundness (ovality) The out of roundness is the difference between maximum and minimum diameter of the wire at any cross-section and shall not be more than one half of the total tolerance given in Table 1

32、. For diameters d from 0,050 mm to 25,00 mm, the tolerances on diameter shall be as follows: Table 1 Diameter tolerances Dimensions in millimetres Diameter tolerance Wire diameter range mm d T1 T2 T3 T4 T5 0,003 0,050 d 1 000 0,10 % DIN EN 10218-2:2012-03 EN 10218-2:2012 (E) 9 5.2 Tolerance and stra

33、ightness There are three classes of straightness of cut lengths given in Table 4 for wire diameters specified in Table 5. The purchaser shall select the appropriate class required. Figure 3 illustrates the measurement of out of straightness. Table 4 Tolerance of straightness of cut lengths Class L a

34、= 500 mm L a= 1 000 mm Rolling test 1 a = 0,5 mm a = 2 mm will roll down an incline of 1 in 10 2 a = 1,0 mm a = 4 mm 3 No requirementaTest length. For classes 1 and 2, the cut lengths shall also meet the requirements of the rolling test which is performed on a smooth glass incline. Cut lengths are p

35、laced on the incline to allow free rolling. Table 5 Straightness test lengths Wire diameter d mm Test length L mm 2,00 d 6,00 500 6,00 d 13,00 500 or 1 000 NOTE Wire of less than 2,00 mm diameter has insufficient rigidity in length making the measurement a difficult. The test should be agreed betwee

36、n purchaser and supplier. Key a Out of straightness in mm. This is measured at the mid point of the test sample length and a is the distance from the inside of the wire to the straight edge. L Length in mm Figure 3 Measurement of out of straightness 6 Length of wire in coil With a wire of known size and density, the length of the coil can be computed having weighed the mass of the coil. DIN EN 10218-2:2012-03