DIN 2510-6-2013 Bolted connections with waisted shank - Part 6 Cap nuts《带有不脱出螺钉的螺栓连接件 第6部分 盖型螺母》.pdf

《DIN 2510-6-2013 Bolted connections with waisted shank - Part 6 Cap nuts《带有不脱出螺钉的螺栓连接件 第6部分 盖型螺母》.pdf》由会员分享，可在线阅读，更多相关《DIN 2510-6-2013 Bolted connections with waisted shank - Part 6 Cap nuts《带有不脱出螺钉的螺栓连接件 第6部分 盖型螺母》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、May 2013Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.0

2、60.20!%K“2044094www.din.deDDIN 2510-6Bolted connections with waisted shank Part 6: Cap nuts,English translation of DIN 2510-6:2013-05Schraubenverbindungen mit Dehnschaft Teil 6: Kapselmuttern,Englische bersetzung von DIN 2510-6:2013-05Assemblages par boulons tige allge Partie 6: crous chapeau,Traduc

3、tion anglaise de DIN 2510-6:2013-05SupersedesDIN 2510-6:1974-09www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 9 pages08.13 DIN 2510-6:2013-05 2 A comma is used as the decimal marker. Contents Page Foreword 3 1 Scope 4 2 Normative refer

4、ences 4 3 Dimensions .5 4 Technical delivery conditions 8 5 Designation 8 6 Marking .8 Annex A (informative) Explanatory notes .9 DIN 2510-6:2013-05 3 Foreword This standard has been prepared by Working Committee NA 067-00-03 AA Verbindungselemente mit metrischem Innengewinde of the Normenausschuss

5、Mechanische Verbindungselemente (Fasteners Standards Committee). The DIN 4000-161-1 tabular layout of product properties applies to cap nuts covered by this standard. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not b

6、e held responsible for identifying any or all such patent rights. DIN 2510, Bolted connections with waisted shank consists of: Part 1: Survey, range of application and examples of installation Part 2: Metric threads with large clearance, nominal dimensions and limits Part 3: Stud-bolts Part 4: Studs

7、 Part 5: Hexagon nuts Part 6: Cap nuts Part 7: Extension sleeves Part 8: Threaded holes for studs Amendments This standard differs from DIN 2510-6; 1974-09 as follows: a) horizontal bottom of bore has been included; b) the tapped hole, represented in detail X in Figure 1, is fully threaded; c) illus

8、trations of M12 to M56 are no longer included in Figure 1; d) the figures have been revised and Figures 2 and 3 added; e) designation examples have been extended: f) in accordance with DIN ISO 965-1, symbol d1has been changed to D; g) the number of positions after the decimal comma has been harmoniz

9、ed for relevant dimensions; h) normative references have been updated; i) an informative Annex with explanatory notes has been included; j) the document has been editorially revised. Previous editions DIN HNA M11: 1924-02 DIN 80711: 1944-12, 1953-04 DIN 2510-3: 1963-08 DIN 2510-6: 1971-08, 1974-09 D

10、IN 2510-6:2013-05 4 1 Scope This standard specifies the characteristics of cap nuts for bolted connections with waisted shank in product grade T2 with metric coarse thread from M12 to M1206. 2 Normative references The following documents, in whole or in part, are normatively referenced in this docum

11、ent and are indispens-able for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 267-13, Fasteners Technical delivery conditions Part 13: Parts for bolted connections wi

12、th specific mechanical properties for use at temperatures ranging from 200 C to +700 C DIN 267-29, Fasteners Product grades for parts for bolted connections for use at temperatures ranging from 200 C to +700 C DIN 2510-7 Bolted connections with reduced shank Extension sleeves DIN 908, Internal drive

13、 screw plugs with collar Cylindrical thread DIN 4000-161, Tabular layout of product properties Part 161: Fasteners with internal thread DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 6157-2, Fasteners Surface discontinuities Part 2: Nuts

14、 DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN 2510-6:2013-05 5 3 Dimensions See Figures 1 to 3

15、 and Table 1. Dimensions in millimetres aPlain bore for D M56, tapped bore for screw plug DIN 908 M481,5 for D M64. bBottom of bore at manufacturers discretion (horizontal or countersunk by 120). cMarking dTapped bore for screw plug DIN 908 M481,5 for D M64. a) Type AF Standard type (notation) Other

16、 relevant dimensions and details as for type AF. b) Type BF For internal centering with extension sleeve as in DIN 2510-7 Figure 1 Cap nut (notation) DIN 2510-6:2013-05 6 Other relevant dimensions and details as for type AF. aPlain bore for D M56, tapped bore for screw plug DIN 908 M481,5 for D M64

17、(see Figure 1a). Figure 2 Cap nut of type AF, bottom of bore countersunk by 120 (Example) Other relevant dimensions and details as for type AF. aPlain bore for D M56, tapped bore for screw plug DIN 908 M481,5 for D M64 (see Figure 1a). Figure 3 Cap nut of type AF with horizontal bottom of bore (Exam

18、ple) DIN 2510-6:2013-05 7 Table 1 Dimensions Dimensions in millimetres Thread size (D) M12 M16 M20 M24 M27 M30 M33 M36 M39 M42 M45 M48 b 18 20,5 24 27,5 30,5 35 38 40,5 43 46 48,5 53,5 d221,0 26,0 31,0 35,0 40,0 45,0 49,0 53,5 58,5 63,5 68,5 73,5 d314,5 18,5 22,5 26,5 30,5 33,5 36,5 39,5 42,5 45,5 4

19、9,5 53,5 d49,0 13,0 15,0 17,5 20,0 23,0 26,0 28,0 31,5 33,5 36,0 39,0 d54 6 6 10 10 10 10 10 10 10 10 10 e min. 18,90 21,10 26,75 30,14 35,72 39,98 45,63 45,63 51,28 55,80 55,80 61,31 k 7 10 13 14 16 17 22 22 23 23 26 26 l133 40 49 56 62 68 77 82 86 92 98 103 l229,5 34,5 40,0 45,5 50,5 55,0 60,0 64,

20、5 67,0 72,0 74,5 81,5 l323,0 27,5 32,0 37,5 40,5 45,0 48,0 52,5 55,0 60,0 62,5 67,5 g 13 17 21 25 28 31 34 37 40 43 46 49 s 17 19 24 27 32 36 41 41 46 50 50 55 t 2,0 2,0 2,5 3,0 3,0 3,5 3,5 4,0 4,0 4,5 4,5 5,0 Mass (7,85 kg/dm3) kg per 1 000 units 70 110 190 240 370 510 700 840 1 070 1 370 1 600 1 9

21、00 Thread size (D) M52 M56 M64 M726 M806 M906 M1006 M1106 (M1206) b 57,0 60,5 69,5 77,0 84,0 93,0 102,0 111,0 120,0 d278,5 83,5 93,5 105,0 115,0 130,0 146,0 160,0 176,0 d357,5 63,0 71,0 79,0 87,0 97,0 107,0 119,0 129,0 d442,0 47,5 54,0 58,0 65,0 77,0 89,0 100,0 108,0 d510 10 M481,5 e min. 66,96 72,6

22、1 83,91 89,56 100,72 117,67 134,62 151,42 162,72 k 27 27 32 32 36 41 45 50 54 l1109 115 130 140 152 168 183 199 214 l285,0 90,5 99,5 107,0 114,0 123,0 132,0 141,0 152,0 l371,0 76,5 85,5 93,0 100,0 109,0 118,0 127,0 136,0 g 53 57 65 73 81 91 101 111 121 s 60 65 75 80 90 105 120 135 145 t 5,0 5,5 6,0

23、6,0 6,0 6,0 6,0 6,0 6,0 Mass (7,85 kg/dm3) kg per 1 000 units 2 400 2 900 4 200 5 700 7 300 10 700 14 800 19 900 20 100 The bracketed thread size should be avoided if possible. DIN 2510-6:2013-05 8 4 Technical delivery conditions See Table 2. Table 2 Technical delivery conditions Material Steel Gene

24、ral requirements DIN ISO 8992 Thread size Tolerance class 6H Standards DIN ISO 261 and DIN ISO 965-1 Mechanical properties MaterialsaDIN 267-13 Standard Limit deviations, geometrical tolerances Product grade T2 Standard DIN 267-29 Surface finish Coating DIN EN ISO 4042 applies with regard to electro

25、plating. Surface dicontinuities DIN EN ISO 6157-2 applies with regard to surface discontinuities. Acceptance inspection DIN EN ISO 3269 applies with regard to acceptance inspection. aOther product grades or materials shall be subject to agreement. 5 Designation Designation of a type AF cap nut with

26、metric thread M30, made of 21CrMoV5-7 (code letters GA): Cap nut DIN 2510 AF M30 21CrMoV5-7 The part of the designation specifying the material can be replaced by the code letters. Designation of a type AF cap nut with metric thread M30, made of 21CrMoV5-7 (code letters GA): Cap nut DIN 2510 AF M30

27、GA Designation of a type AF cap nut without bore (O) and with metric thread M30, made of 21CrMoV5-7 (code letters GA): Cap nut DIN 2510 AF OM30 21CrMoV5-7 6 Marking DIN 267-13 shall apply to marking. DIN 2510-6:2013-05 9 Annex A (informative) Explanatory notes The use of cap nuts according to this s

28、tandard permits a smaller design of the bolted parts, compared to when using hexagon nuts, as hexagon nuts require larger pitch circle diameters and centre-to-centre distances for the same thread diameter, due to the larger size of the hexagon. Dimension l3 permits a depth of bolt engagement which c

29、orresponds with a minimum bearing thread length of 0,9 the nominal diameter of thread D and which permits a gradation of bolt length in increments of 5 mm to 5 mm. However, it was necessary to provide for a slope of 45 from diameter g to diameter d4to ensure that a minimum clearance a remains betwee

30、n the bolt end face and the end face of the undercut in accordance with DIN 2510-1. Bore d4serves to accommodate the point carrying the widths across flats for stud-bolts and studs according to DIN 2510-3 and DIN 2510-4. Cap nuts above size M56 are equipped with a bore hole of thread size M481,5, in order to enable a heating rod to be inserted into the heating bore of the bolt, thus ensuring that the heating bore can be closed with a screw plug. Cap nuts can be manufactured with either a 120 countersunk or a horizontal (if manufactured with indexable insert drills) bottom of bore.