DIN 1479-2005 Hexagon turnbuckles《六角松紧螺套》.pdf

《DIN 1479-2005 Hexagon turnbuckles《六角松紧螺套》.pdf》由会员分享，可在线阅读，更多相关《DIN 1479-2005 Hexagon turnbuckles《六角松紧螺套》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 DEUTSCHE NORM September 2005DIN 1479 ICS 21.060.20; 21.060.70 Supersedes DIN 1479:1998-02 Hexagon turnbuckles Sechskant-Spannschlossmuttern Document comprises 6 pagesTranslation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text. No p

2、art of this translation may be reproduced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 6 www.din.de www.beuth.de !,ohl“09.06 9766973DIN 147

3、9:2005-09 2 Foreword This standard has been prepared by Technical Committee FMV-AA 3.12.2 Spannschlsser of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). The revision of this standard was considered necessary since the proper length of engagement of the connecti

4、ng component could not be easily checked when using turnbuckles of the type specified in the February 1998 edition. However, in order to ensure the safe use of such turnbuckles, particularly in the field of structural bolting, the length of engagement of the connecting component needs to be at least

5、 equal to length t. The control bore on the turnbuckles specified here ensures this. The DIN 4000-2-8.4 tabular layout of article characteristics shall apply to turnbuckles covered in this standard. NOTE Parts of DIN 4000-2 are intended to be superseded by DIN 4000-161 in which case the DIN 4000-161

6、-6 tabular layout of article characteristics will apply to turnbuckles complying with this standard. Amendments This standard differs from DIN 1479:1998-02 as follows: a) Control bores for checking the length of engagement of connecting components have been specified. b) Tolerances for length and wi

7、dth across flats have been specified. c) For M30 turnbuckles, the minimum width across corners has been corrected. d) For the steel used, property class 5 has been specified. e) Hot dip galvanized coatings have been included. f) Non-electrolytically applied zinc flake coatings have been included. g)

8、 The designation of turnbuckles made of austenitic steel has been amended. Previous editions DIN 1479: 1975-09, 1998-02 DIN 1479-1: 1942x-04 1 Scope This standard specifies dimensions and technical delivery conditions for M6 to M30 hexagon turnbuckles with widths across flats as in DIN ISO 272, of p

9、roduct grade A and made of steel or austenitic steel. 2 Normative references The following reference documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includin

10、g any amendments) applies. DIN 4000-2:1999-12, Tabular layouts of article characteristics for bolts, screws and fit bolts DIN EN 20898-2, Mechanical properties of fasteners Part 2: Nuts with coarse pitch thread and specified proof load values DIN 1479:2005-09 3 DIN EN ISO 3269, Fasteners Acceptance

11、inspection DIN EN ISO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and fit bolts Product grades A, B and C DIN EN ISO 10683, Faste

12、ners Non-electrolytically applied zinc flake coatings DIN EN ISO 10684, Fasteners Hot dip galvanized coatings DIN EN ISO 16048, Passivation of corrosion-resistant stainless steel fasteners DIN ISO 272, Fasteners Hexagon products Widths across flats DIN ISO 965-2, ISO general purpose metric screw thr

13、eads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality DIN 1479:2005-09 4 3 Dimensions Turnbuckle dimensions shall be as given in figure 1 and table 1. a) For sizes up to M16, with overlapping threads b) For sizes M20 and above, with recess (ot

14、her dimensions and details as for sizes up to M16) a Left-hand thread, marked optionally by L or by a groove cut in the corners of the hexagon b Right-hand thread c Control bore for checking the length of engagement of the connecting component d Dimension t is the minimum length of engagement of the

15、 connecting component Figure 1 Turnbuckle dimensions (notation) DIN 1479:2005-09 5 Table 1 Turnbuckle dimensions Dimensions in millimetres Thread size (d1) M6 M8 M10 M12 M16 M20 M24 M30 d2 21 26 32 d34 0,3 Nominal dimension 30 35 45 55 75 95 115 125 max. 30,5 35,8 45,8 55,8 75,8 95,8 115,8 126,2 l m

16、in. 29,5 34,2 44,2 54,2 74,2 94,2 114,2 123,8 m 22,5 25 33 40 55 24 29 36 Nominal dimension = max. 10 13 16a18a24 30 36 46 s min. 9,78 12,73 15,73 17,73 23,67 29,16 35 45 Hexagon e min. 11,05 14,38 17,77 20,03 26,75 32,95 39,55 50,85 t 9,5 12 14 17 22 26 31 38 Length of engagement 15 15 21 25 35 47

17、57 53 aNew widths across flats, see clause 5 for designation. 4 Technical delivery conditions Table 2 Technical delivery conditions Material Steel (St) Austenitic steel Property class 5 A4-50 Mechanical properties As specified in DIN EN 20898-2 DIN EN ISO 3506-2 Tolerance 6H Thread As specified in D

18、IN ISO 965-2 Product grade A Limit deviations and geometrical tolerances As specified in DIN EN ISO 4759-1 Surface finish As processed. DIN EN ISO 4042 shall apply with regard to electroplating. DIN EN ISO 10684 shall apply with regard to hot dip galvanizing. DIN EN ISO 10683 shall apply with regard

19、 to zinc flake coatings. Passivation in accordance with DIN EN ISO 16048. Acceptance inspection DIN EN ISO 3269 shall apply with regard to acceptance inspection. DIN 1479:2005-09 6 5 Designation Designation of an M16 turnbuckle (SP) with right-hand and left-hand thread, of property class 5: Turnbuckle DIN 1479 SP M16 5 Designation of an M12 turnbuckle (SP) with right-hand and left-hand thread, with a width across flats of 18 mm (SW18) as in DIN ISO 272, made of austenitic steel A4 (A4) of property class 50: Turnbuckle DIN 1479 SP M12 SW18 A4 50