CSA T568 1-4-2005 Commercial building telecommunications cabling standard Part 1 General requirements Addendum 4 Recognition of category 6 and 850 nm laser-optimized 50 125 μm m.pdf

《CSA T568 1-4-2005 Commercial building telecommunications cabling standard Part 1 General requirements Addendum 4 Recognition of category 6 and 850 nm laser-optimized 50 125 μm m.pdf》由会员分享，可在线阅读，更多相关《CSA T568 1-4-2005 Commercial building telecommunications cabling standard Part 1 General requirements Addendum 4 Recognition of category 6 and 850 nm laser-optimized 50 125 μm m.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 T568.1-4-05(ANSI/TIA-568-B.1-4-2003)Commercial building telecommunications cabling standard Part 1: General requirements Addendum 4 Recognition of category 6 and 850 nm laser-optimized 50/125 m multimode optical fiber cabling CSA Standard T568.1-4-05 (ANSI/TIA-568-B.1-4-2003) Commercial building te

2、lecommunications cabling standard Part 1: General requirements Addendum 4 Recognition of category 6 and 850 nm laser-optimized 50/125 mm multimode optical fiber cabling Published in May 2005 by Canadian Standards Association A not-for-profit private sector organization 5060 Spectrum Way, Suite 100,

3、Mississauga, Ontario, Canada L4W 5N61-800-463-6727 416-747-4044 Visit our Online Store at www.ShopCSA.ca Commercial building telecommunications cabling standard Part 1: General requirements Addendum 4 Recognition of category 6 T568.1-4-05 and 850 nm laser-optimized 50/125 mm multimode optical fiber

4、cabling CSA/2 Canadian Standards Association May 2005 T568.1-4-05 Commercial building telecommunications cabling standard Part 1: General requirements Addendum 4 Recognition of category 6 and 850 nm laser-optimized 50/125 mm multimode optical fiber cabling CSA Preface This is the first edition of CS

5、A T568.1-4, Commercial building telecommunications cabling standard Part 1: General requirements Addendum 4 Recognition of category 6 and 850 mm laser-optimized 50/125 mm multimode optical fiber cabling. This Standard is an adoption of the identically titled ANSI/TIA (American National Standards Ins

6、titute/Telecommunications Industry Association) Standard 568-B.1-4-2003 and is the product of the Telecommunications Industry Association TR-42 Technical Committee, which included a number of Canadian members in order to ensure that Canadian perspectives and requirements were addressed. It is writte

7、n in SI (metric) units with yard/pound (imperial) units in parentheses. This Standard has been adopted with no technical deviations. Where code requirements or regulations necessitate changes from US to Canadian references, they should be made by the user, as follows: (a) Throughout this Standard, r

8、eplace the term “American” with “Canadian”, as applicable. (b) Throughout this Standard, replace the term “state” with “provincial or territorial”, as applicable. (c) Throughout this Standard, replace “NEC” with “CE Code, Part I” (Canadian Electrical Code), as applicable. In addition, (i) where refe

9、rence is made to “conduit”, replace it with “conduit/EMT” (electrical metallic tubing) because, in accordance with the Canadian Electrical Code, Part I, EMT is not considered a type of conduit; and (ii) the definitions of the following terms are to be taken from the Canadian Electrical Code, Part I:

10、 “Bonding”, “Ground”, and “Raceway”. (d) Throughout this Standard, where reference is made to “FCC”, replace it with “CRTC” (Canadian Radio-television and Telecommunications Commission), or “Industry Canada”, as applicable. (e) The following Standards, published by the Canadian Standards Association

11、, are adoptions of TIA/EIA Standards. The requirements of these CSA Standards take precedence over the TIA/EIA Standards on which they are based; any reference in CSA T568.1-4 to the TIA/EIA Standard is to be replaced by a reference to the equivalent Canadian Standard: Commercial building telecommun

12、ications cabling standard Part 1: General requirements Addendum 4 Recognition of category 6 T568.1-4-05 and 850 nm laser-optimized 50/125 mm multimode optical fiber cabling May 2005 Canadian Standards Association CSA/3 (i) T568.1-05, Commercial building telecommunications cabling standard Part 1: Ge

13、neral requirements; (ii) T568.2-05, Commercial building telecommunications cabling standard Part 2: Balanced twisted-pair cabling components; (iii) T568.2-1-05, Commercial building telecommunications cabling standard Part 2: Balanced twisted pair cabling components Addendum 1 Transmission performanc

14、e specifications for 4-pair 100 W category 6 cabling; (iv) T568.3-05, Optical fiber cabling components standard; and (v) T568.3-1-05, Optical fiber cabling components standard Addendum 1 Additional transmission performance specifications for 50/125 mm optical fiber cables. (f) Throughout this Standa

15、rd, replace the term “Listed” with “Approved as applied to electrical equipment”. This Standard was reviewed for Canadian adoption by the CSA Technical Committee on Telecommunications Wiring Systems, under the jurisdiction of the Strategic Steering Committee on Information and Communications Technol

16、ogy, and has been formally approved by the Technical Committee. A list of the members of the Technical Committee is available upon request. May 2005 Canadian Standards Association 2005 All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permiss

17、ion of the publisher. TIA material is reprinted with permission. Inquiries regarding this CSA Standard should be addressed to Canadian Standards Association 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6 1-800-463-6727 416-747-4044 www.csa.ca TIA STANDARD ANSI/TIA-568-B.1-4-2003

18、Approved: February 26, 2003 Commercial Building Telecommunications Cabling Standard Part 1: General Requirements Addendum 4 Recognition of Category 6 and 850 nm Laser-Optimized 50/125 m Multimode Optical Fiber Cabling TIA-568-B.1-4 (Addendum No. 4 to TIA/EIA-568-B.1) FEBRUARY 2003 TELECOMMUNICATIONS

19、 INDUSTRY ASSOCIATION Representing the telecommunications industry in association with the Electronic Industries Alliance NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitati

20、ng interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufactu

21、ring or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the Ame

22、rican National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. Further details of the development process are available in the TIA Engineering

23、Manual, located at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and h

24、ealth practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-4425-AD4, formulated under the cognizance of the TIA TR-42.1 Subcommittee on Commercial Building Telecommunications Cabling.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATI

25、ON 2003 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. All rights reserved NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed (the “Document”) has been prepared by one or more Engineering Committees or Formulating Group

26、s of the Telecommunications Industry Association (“TIA”). TIA is not the author of the Document contents, but publishes and claims copyright to the Document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees and Formulating Groups are expected to c

27、onduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm. TIAs function is to administer the process, but not the content, of document preparation in acco

28、rdance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). TIA does not evaluate, test, verify or investigate the information, accuracy, soundness, or credibility of the contents of the Document. In publishing the Document, TIA di

29、sclaims any undertaking to perform any duty owed to or for anyone. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for

30、IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire

31、 into, the scope or validity of any claims of IPR. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, E

32、XPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSL

33、Y DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMEN

34、T OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING

35、 DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELE

36、MENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the TIA and may not be reproduced without prior permission of the Telecommunications Industry Association. For information

37、consult our website at http:/www.tiaonline.org/about/faqDetail.cfm?id=18 Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 U.S.A.

38、 or call U.S.A. and Canada 1-800-854-7179, International (303) 397-7956 TIA-568-B.1-4 Recognition of Category 6 and 850 nm Laser-Optimized 50/125 m Multimode Optical Fiber Cabling TABLE OF CONTENTS 1 INTRODUCTION 1 2 CLAUSE REVISIONS.1 iTIA-568-B.1-4 1 INTRODUCTION The purpose of this addendum is to

39、 recognize balanced twisted pair category 6 cabling and 850 nm laser-optimized 50/125 m multimode optical fiber cable by revising sub-clauses 4.4, 4.5, 5.3 and 11.2.2 of TIA/EIA-568-B.1. These revisions are identified in the following text with additions shown in bold italics and deletions shown as

40、strikeout. 2 CLAUSE REVISIONS 4.4 Recognized cables Two types of cables are recognized and recommended for use in the horizontal cabling system. These cables are: a) four-pair 100-ohm category 3 (ANSI/TIA/EIA-568-B.2), category 5e (ANSI/TIA/EIA-568-B.2) or category 6 (ANSI/TIA/EIA-568-B.2-1) unshiel

41、ded twisted-pair (UTP) or screened twisted-pair (ScTP) cables (ANSI/TIA/EIA-568-B.2) b) two or more optical fiber multimode cable, either 62.5/125 m or 50/125 m (ANSI/TIA/EIA-568-B.3 or ANSI/TIA/EIA-568-B.3-1) At this time, 150-ohm shielded twisted-pair (STP-A) cable is a recognized media type (ANSI

42、/TIA/EIA-568-B.2). It is not, however, recommended for new cabling installations and is expected to be removed from the next revision of this Standard. Recognized cables, associated connecting hardware, jumpers, patch cords, equipment cords, and work area cords shall meet all applicable requirements

43、 specified in ANSI/TIA/EIA-568-B.2, ANSI/TIA/EIA-568-B.2-1, and ANSI/TIA/EIA-568-B.3 and ANSI/TIA/EIA-568-B.3-1. When bundled and hybrid cables are used for horizontal cabling, each cable type shall be recognized and meet the transmission and color-code specifications for that cable type given in AN

44、SI/TIA/EIA-568-B.2, ANSI/TIA/EIA/-568-B.2-1, and ANSI/TIA/EIA-568-B.3 and ANSI/TIA/EIA-568-B.3-1. Additionally, bundled or hybrid copper cables shall meet the bundled or hybrid cable requirements in ANSI/TIA-568-B.2. These requirements apply to hybrid cables and bundled cables assembled prior to ins

45、tallation, sometimes referred to as loomed, speed-wrap, or whip cable constructions. NOTES 1 Annex C provides a brief description of a number of other horizontal cables that have been used in telecommunications. These cables, as well as others, may be effective for specific applications. Although th

46、ese cables are not part of the requirements of this Standard, they may be used in addition to the minimum requirements of this Standard. 2 Hybrid cables consisting of optical fiber and copper conductors are sometimes referred to as composite cables. 1TIA-568-B.1-4 4.5 Choosing types of cabling This

47、Standard recognizes the importance of both voice and data telecommunications in a commercial building. A minimum of two telecommunications outlet/connectors shall be provided for each individual work area as shown in figure 4-1. One telecommunications outlet/connector may be associated with voice an

48、d the other with data. Consideration should be given to installing additional outlets/connectors based on present and projected needs. The two telecommunications outlet/connectors shall be configured as: a) One telecommunications outlet/connector shall be supported by a four-pair 100-ohm cable, cate

49、gory 3 or higher (category 5e or category 6 recommended) as specified in ANSI/TIA/EIA-568-B.2 and ANSI/TIA/EIA-568-B.2-1. b) The other/second telecommunications outlet/connector(s) shall be supported by a minimum of one of the following horizontal media. This media choice should be based on present and projected needs. 1) Four-pair 100-ohm cable, either category 5e or category 6, cable as specified in ANSI/TIA/EIA-568-B.2 and ANSI/TIA/EIA-568-B.2-1. 2) Two-fiber multimode optical fiber cable, either 62.5/125