CEPT ETS 300 341-1995 Radio Equipment and Systems (RES) Technical Characteristics and Test Conditions for Radio Equipment Using an Integral Antenna Transmitting Signals to Initiate.pdf

《CEPT ETS 300 341-1995 Radio Equipment and Systems (RES) Technical Characteristics and Test Conditions for Radio Equipment Using an Integral Antenna Transmitting Signals to Initiate.pdf》由会员分享，可在线阅读，更多相关《CEPT ETS 300 341-1995 Radio Equipment and Systems (RES) Technical Characteristics and Test Conditions for Radio Equipment Using an Integral Antenna Transmitting Signals to Initiate.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、STD-CEPT ETS 300 34%-ENGL 1975 II 232b414 0014887 5Tb = EUROPEAN CONFERENCE OF POSTAL AND TELECOMMUNICATIONS ADMINISTRATIONS Application form for testing to ETS 300 341 Radio Equipment and Systems (RES) Technical characteristics and test conditions for radio equipment using an integral antenna trans

2、mitting signals to initiate a specific response in the receiver The submission documentation to a National Regulatory Body for Type approval purposes shall consist of two parts; Part one. Application form Patt two. Test report form Version: O1 /95 Adopted by ERC WG RR: February 1995 Published by: CE

3、PT Liaison Office P.O. Box CH-3001 BERNE Telephone: 41 313382501 Facsimile: 41313382078 Telex : 911089 CEPT CH STD*CEPT ETS 300 341-ENGL 3775 W 232b414 OOL4BBB 432 D APPLICATION FORM TO TEST LABORATORY FOR TESTING TO ESS 300 341 The application form shall be used for equipment submitted for testing

4、in accordance with ETS 300 341 intended for the transmission of signals to initiate a specific response in the receiver. The application form shall be completed by the applicant and submitted to a test laboratory accredited in accordance with EN45001 and EN45002 or ISO guides 25 and 38 or a national

5、 standard conforming to EN45001 and EN45002 or IS0 guides 25 and 38. PLEASE READ THE FOLLOWINQ NOTES: Note (a): Number of items for type testing More than one item of equipment may be required to be submitted for type testing where an equipment needs to be modified to provide connections to facilita

6、te testing, i.e. measurements requiring direct connections to be made, for example, audio measurements. In such cases a second un-modified equipment may be required for radiated i.e. case or cabinet radiation or ERP (effective radiated power) measurements to be performed. hill details of modificatio

7、ns are to be provided. Note (b): Differing regulatory requirements ETS 300 341 allows for variations in frequency range, maximum and average radiated power, channel separation etc. to reflect differing national regulatory requirements. Manufacturers producing equipment to this ETS may wish to offer

8、an equipment of the same basic design in a number of different forms with different RF characteristics, such as the frequency range, channel separation, transmitter power etc. This is subsequently referred to as a family of equipments. Each equipment in the family must be given a unique Type Designa

9、tion. In the case of equipment with different frequency ranges and channel separations, a separate set of test results will be required for each frequency range and each channel separation offered. In the case of equipment with different transmitter powers, the procedures laid down in ETC 300 341 pe

10、rmit use of a single set of test results. Note (a): Equipment with differing optional features If an applicant wishes to obtain type approval, on the basis of a single set of test results for a family of equipments derived from the same basic design, where the equipments in the family have different

11、 operational features, such as audio output powers, which are not a requirement of FTS 300 341, then the following considerations shall be observed. i) Any operational feature, not including signalling, shall be clearly defined by the applicant at the time of application, so that an assessment can b

12、e made by the national regulatory authority as to whether the addition of the feature concerned, which may be achieved in hardware or software, can affect any of the performance parameters measured in accordance with ETS 300 341, and thus assess whether further testing is needed. ii) it is further i

13、ntended to provide guidance on the above in consultation with CEPT WGRR. It is intended to periodically revise the Technical Report as new operational features are developed. 1 i) in the case of combined speech/non-speech equipment, the speech part of the equipment should be tested to the requiremen

14、ts of ETS 300 296, and additionally the measurements described in the following sub- clauses of ETS 300 341 shall be carried out: 8.3 Adjacent channel power 9.1 Average usable sensitivity (field strength, responses) ii) In the case where an equipment has already been type approved according to ETS 3

15、00 296, and is resubmitted for type testing to ETS 300 341 the additional measurements as described in the following sub-clauses shall be carried out: 8.3 Adjacent channel power 8.4 Transmitter radiated spurious emissions 9.1 Average usable sensitivity (field strength, responses) Note (a): Accessori

16、es It is the applicants responsibility when submitting equipment (s) to the test laboratory to provide appropriate connectors or alternative coupling arrangements to facilitate the connection of test equipment by the test laboratory to the equipment under test (E.U.T.). This should enable: i) operat

17、ion of the equipment “press to talk“ transmitter operation; ii) access to the equipment modulator input; iii) access to the signal at the demodulator output; iv) access to the analogue output of the RF part; v) coupling arrangement (e.g. optical or acoustic coupling); vi) access to the receiver audi

18、o output. If the equipment has more than one audio output then suitable connectors for these are also required. It is not permissible to access the receiver audio output in parallel with the loudspeaker. vii) means of connecting the equipment to an external power supply. Nota (f): Pre-production mod

19、el For type approval to be granted on the basis of tests conducted on a pre- production model, that model must be manufactured to the same production drawings and manufacturers specification as the later production models. Where this is not the case the national regulatory authority reserves the rig

20、ht to require either partial or full type testing to be carried out on the final production equipment. Note (8): Applicants responsibility It is the applicants responsibility to obtain information on the appropriate technical parameters (channel spacing, power level, .) defined in each countrys nati

21、onal regulations before applying for type approval. It is also the applicants responsibility to ensure that the equipment meets all the regulatory requirements for marking in the country where type approval is being sought. 2 APPLICANTS DETAILS MANUFACTURER 0 CATEGORY OF APPLICANT (please tick ree-

22、(a) vant box opposite If box (b), (c) or (d) is ticked complete details in box below with respect to the manufacturer. IMPORTER DISTRIBUTOR 0 0 (b) (cl (d) 0 AGENT COMPANY NAME ADDRESS . . NAME FOR CONTACT PURPOSES . TELEPHONE NO: FAX NO: TELEX NO: MNFACTURERS DETAILS _ COMPANY NAME . ADDRESS NAME F

23、OR CONTACT PURPOSES TELEPHONE NO: FAX NO: . TELEX NO 3 TYPE DESIGNATION (Note i) The type designation may be either a single alphanumeric code 5 an alphanumeric/ code divided into two parts. Please fill in EITHER : TYPE DESIGNATION AS A SINGLE ALPHANUMERIC CODE OR : TYPE DESIGNATION IN TWO PARTS : 1

24、. EQUIPMENT SERIES NO. ( “MODEL NUMBER“) (Note 2) 111111111111111111111 AND 2. EQUIPMENT SPECIFIC NO. (Note 3) (“IDENTIFICATION NO“) 11111111111111111111111 Notes 1) This is the manufacturers numeric or alphanumeric code or name that is specific to a particular equipment. It may contain information

25、in coded form on the characteristics of the equipment e.g. frequency, power. The manufacturer is free to choose the form of the type designation. 2) This is the number, code or trade name used by the manufacturer to describe a series or family of equipment of substantially the same mechanical and el

26、ectrical construction which will include a number of related equipments. This number is often referred to as the “model no.n. 3) This is the manufacturers identification number given to a specific equipment in the series or family of equipments. It is often referred to as the “identification number“

27、. 4 STDmCEPT ETS 300 343-ENGL 3995 2326434 0034892 9h3 OTHER APPLICATIONS FOR TYPE TESTING TO ET8 300 341 Has the the equipment been previously type tested to ETC 300 341 ? YES o NO o If “yes“ please provide details : TYPE TESTING TO OTHER ET8 Has the speech part of the equipment been previously typ

28、e tested to ETC 300 296 ? YES o NO Is the equipment simultaneously submitted for type testing to ETC 300 296 and ETS 300 341 ? CI NO o YES Is there any supplementary information ? 5 STD-CEPT ETS 300 341-ENGL 1995 W 2326414 0014893 8TT 9 DETAILS OF HANDPORTABLE EQUIPMENT Transceiver n Battery charger

29、 0 I I Category (see ETS 300 341 sub-clause 5.2.1) 0 Does this handportable equipment has an internal power supply ? (see ETC 300 341 sub-clause 5.1.1) Yes 0 n No U As a result : EXTREME TEMPERATURE RANGE over which equipment is to be type tested : -2OOC to +55OC n u and OC to +3OoC when appropriate

30、 (see sub-clause 5.1.1) I II I Any other details CHARACTERISTICS OF ICIRAL ANPE“ Land mobile service; Technical characteristics and test conditions for radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver Amendment 1 to Edition 1 - 1997-03 - 12 Pages Imp1 Remarks Yes No FIN HNG HOL HRV NOR POR SVN