CEN TS 13598-3-2012 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC-U) polypropylene (PP) and polyethylene (PE) .pdf

《CEN TS 13598-3-2012 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC-U) polypropylene (PP) and polyethylene (PE) .pdf》由会员分享，可在线阅读，更多相关《CEN TS 13598-3-2012 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC-U) polypropylene (PP) and polyethylene (PE) .pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPlastics piping systems for non-pressure undergrounddrainage and sewerage Unplasticized poly(vinyl chloride)(PVC-U), polypropylene(PP) and polyethylene (PE)Part 3: Guidance for a

2、ssessment of conformityPD CEN/TS 13598-3:2012National forewordThis Published Document is the UK implementation of CEN/TS 13598-3:2012.The UK participation in its preparation was entrusted by Technical CommitteePRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plastics piping fornon-pressure

3、 applications.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by

4、 BSI Standards Limited 2012ISBN 978 0 580 76362 5ICS 93.030Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was published under the authority of theStandards Policy and Strategy Committee on 31 May 2012.Amendments issued since publicationAmd. No

5、. Date Text affectedPUBLISHED DOCUMENTPD CEN/TS 13598-3:2012TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 13598-3 April 2012 ICS 93.030 English Version Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC

6、-U), polypropylene (PP) and polyethylene (PE) - Part 3: Guidance for assessment of conformity Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement enterrs sans pression - Poly(chlorure de vinyle) non plastifi (PVC-U), polypropylne (PP) et polythylne (PE) - P

7、artie 3: Guide pour lvaluation de la conformit Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 3: Empfehlungen fr die Beurteilung der Konformitt This Technical Specificati

8、on (CEN/TS) was approved by CEN on 14 February 2012 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted

9、into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) u

10、ntil the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu

11、ania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussel

12、s 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 13598-3:2012: EPD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Abbreviat

13、ed terms .85 General 96 Testing and inspection 96.1 Material specification of PVC-U 96.2 Material specification of PP . 106.3 Material specification of PE . 116.4 Grouping 116.4.1 General . 116.4.2 Size groups 116.4.3 Fitting groups 126.5 Type testing (TT) . 126.6 Batch release tests (BRTs) 156.7 Pr

14、ocess verification tests (PVTs) 166.8 Audit tests (ATs) . 186.9 Indirect tests (ITs) . 216.10 Test records 21Annex A (informative) Summary of EN 13598-1 test regime 22Annex B (informative) Summary of EN 13598-2 test regime 23Bibliography . 24PD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 3 Foreword T

15、his document (CEN/TS 13598-3:2012) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and

16、/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 13598, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) is composed of the three following parts:

17、Part 1: Specifications for ancillary fittings including shallow inspection chambers; Part 2: Specifications for manholes and inspection chambers in traffic areas and deep underground installations; Part 3: Guidance for assessment of conformity (CEN/TS) (the present document). According to the CEN/CE

18、NELEC Internal Regulations, the national standards organisations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, L

19、ithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 4 Introduction Figures 1 and 2 are intended to provide general information on the concept of testi

20、ng and organisation of those tests used for the purpose of the assessment of conformity. For each type of tests (i.e. type testing (TT), batch release test (BRT), process verification test (PVT) and audit test (AT), this document details the applicable characteristics to be assessed and the frequenc

21、y and sampling of testing. A typical scheme for the assessment of conformity of compounds, products and assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment of conformity of compounds, formula

22、tions, pipes, fittings, or assemblies by manufacturers, is given in Figure 2. Figure 2 Typical scheme for the assessment of conformity by a manufacturer PD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 5 1 Scope This Technical Specification gives guidance for the assessment of conformity of compounds/f

23、ormulations, products and assemblies in accordance with Parts 1 and 2 of EN 13598 intended to be included in the manufacturers quality plan as part of the quality management system and for the establishment of third-party certification procedures. NOTE In order to help the reader, a basic test matri

24、x is given in Annexes A and B. In conjunction with EN 13598- 1 and -2, this Technical Specification is applicable to ancillary underground drainage fittings including manholes and inspection chambers: for non-pressure underground drainage and sewerage outside the building structure (application area

25、 code “U“), reflected in the marking of products by “U“, and for non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D“) and outside the building structure (application area code “U“), reflected in the marking of products by

26、“UD“. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

27、 amendments) applies. EN 1401-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system EN 13598-1:2010, Plastics piping systems for non-pressure underground drainage and sew

28、erage Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Specifications for ancillary fittings including shallow inspection chambers EN 13598-2:2009, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride

29、) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for manholes and inspection chambers in traffic areas and deep underground installations ISO 3951-1, Sampling procedures for inspections by variables Part 1: Specification for single sampling plans indexed by acceptance quali

30、ty limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 3 Terms and definitions For the purposes of this document, the following terms and definitions given in EN 13598-1:2010 and EN 13598-2:2009 and the following apply. 3.1 certification body impartial body, go

31、vernmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17021 4, 3.2. 3.2 inspection body body th

32、at performs inspection Note 1 to entry: A body can be an organisation, or part of an organisation. SOURCE: EN ISO/IEC 17020:2004 5, 2.2 PD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 6 Note 2 to entry: A inspection body is preferably compliant with EN ISO/IEC 17020:2004 5, 3.3. 3.3 testing laboratory

33、 laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products Note 1 to entry: In the context of this part of EN 13598, the compounds / formulations and products can be subjected to type testing, batch release testing, process

34、verification testing, audit testing and/or witness testing, as applicable. Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 6. 3.4 quality management system management system to direct and control an organisation with regard to quality SOURCE: EN ISO 9000:2005 7, 3

35、.2.3 Note 1 to entry: An example of a quality management system is given in EN ISO 9001 1. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing performed to verify

36、that the material, product, joint or assembly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are done regularly

37、. 3.7 batch release test BRT test performed by or on behalf of the manufacturer on a product batch, which has to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer on products and assemblies at specific in

38、tervals to confirm that type test originally performed on these products and assemblies continue to be valid and that the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release bat

39、ches of products and are carried out as a measure of process control. 3.9 audit test AT test performed by a test laboratory on behalf of an inspection body or certification body to confirm that the compound, product, and assembly continues to conform to the requirements given in the relevant standar

40、d and to provide information to assess the effectiveness of the quality management system PD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 7 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characteristic, having previously

41、 verified its correlation with the test specified 3.11 witness test WT testing accepted by an inspection or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or certification body,

42、 qualified in testing 3.12 material compounds/formulations grouped by families, expressed by generic names, e.g. polypropylene, stainless steel, brass or EPDM Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and Industry, Sub-group on Product Testing Procedure

43、s (EC, DG ENT and IND, SG PTP). 3.13 compound/formulation clearly defined homogenous mixture of base polymer with additives, i.e. anti-oxidants, pigments, stabilisers and others, at a dosage level necessary for the processing and the intended use of the final product 3.14 material batch clearly iden

44、tified quantity of a given homogeneous compound manufactured under uniform conditions and defined and identified by the compound/formulation manufacturer 3.15 product underground ancillary fittings and components intended to provide a means of access to the drainage system of a clearly identified ty

45、pe as specified in Parts 1 and 2 intended to be a part of a the drainage system 3.16 product batch clearly identified collection of products, manufactured consecutively or continuously under the same conditions, using the same compound/ formulation conforming to the same specification Note 1 to entr

46、y: The product batch is defined and identified by the product manufacturer. 3.17 lot clearly identifiable sub-division of a batch for inspection purposes 3.18 sample one or more products drawn from the same production batch or lot, selected at random without regard to their quality Note 1 to entry:

47、The number of products in the sample is the sample size. 3.19 group collection of similar products from which samples are selected for testing purposes PD CEN/TS 13598-3:2012CEN/TS 13598-3:2012 (E) 8 3.20 component product manufactured out of a specific compound/formulation, brought to the market as

48、 part of another product or as a spare part 3.21 joint connection between two products 3.22 assembled component assembled final product using two or more single parts 3.23 thermoplastics fabricated fitting fitting produced from pipe and/or from injection-moulded fittings by thermoforming, solvent-ce

49、menting or welding 3.24 sampling plan specification of the type of sampling to be used combined with the operational specification of the entities or increments to be taken, the samples to be constituted and the measurements or tests to be made EXAMPLE A specific plan which indicates the number of units of products or assemblies to be inspected. 3.25 product type generic description of a product EXAMPLE A pipe or fitting or their main parts, of the same desig