CEN TR 13480-7-2017 Metallic industrial piping - Part 7 Guidance on the use of conformity assessment procedures.pdf

《CEN TR 13480-7-2017 Metallic industrial piping - Part 7 Guidance on the use of conformity assessment procedures.pdf》由会员分享，可在线阅读，更多相关《CEN TR 13480-7-2017 Metallic industrial piping - Part 7 Guidance on the use of conformity assessment procedures.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Metallic industrial pipingPart 7: Guidance on the use of conformity assessment proceduresPD CEN/TR 134807:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06TECHNICALREPORT RAPPORT TECHNIQUETECHNISCHER BERICHTCEN/TR 13480-7 July 2017ICS 23.040.01 Supersedes CEN/TR 1

2、3480-7:2002EnglishVersionMetallic industrial piping - Part 7: Guidance on the use of conformity assessment proceduresTuyauteries industrielles mtalliques - Partie 7 : Guide pour lutilisation des procdures dvaluation de la conformitMetallische industrielle Rohrleitungen - Teil7:Anleitung fr den Gebra

3、uch desKonformittsbewertungsverfahrensThis Technical Report wasapproved by CENon 19 June 2017. It has been drawn up by the Technical Committee CEN/TC 267.CEN members are the nationalstandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yug

4、oslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT

5、EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reservedworldwide for CENnational Members.Ref. No. CEN/TR 13480-7:2017 ENational forewordThis British Standard is th

6、e UK implementation of CEN/TR 134807:2017. It supersedes PD CEN/TR 134807:2002, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PVE/10, Piping systems.A list of organizations represented on this committee can be obtained on request to its secretary.Thi

7、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 97646 9ICS 23.040.01Compliance with a British Standard cannot confer i

8、mmunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMENTPD CEN/TR 134807:2017TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHE

9、R BERICHT CEN/TR 13480-7 July 2017 ICS 23.040.01 Supersedes CEN/TR 13480-7:2002English Version Metallic industrial piping - Part 7: Guidance on the use of conformity assessment procedures Tuyauteries industrielles mtalliques - Partie 7 : Guide pour lutilisation des procdures dvaluation de la conform

10、it Metallische industrielle Rohrleitungen - Teil 7: Anleitung fr den Gebrauch des Konformittsbewertungsverfahrens This Technical Report was approved by CEN on 19 June 2017. It has been drawn up by the Technical Committee CEN/TC 267. CEN members are the national standards bodies of Austria, Belgium,

11、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Swi

12、tzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN natio

13、nal Members. Ref. No. CEN/TR 13480-7:2017 EPD CEN/TR 134807:2017CEN/TR 13480-7:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Application of the PED . 4 4.1 General 4 4.2 Conformity assessment procedures . 4 4.2.1 General 4 4.2.2 Choic

14、e of conformity assessment procedures 4 4.2.3 Conformity assessment procedures and the involvement of Responsible Authorities 5 5 Subcontracting . 5 Annex A (informative) Conformity of industrial piping to the essential safety requirements of Directive 2014/68/EU (Pressure equipment directive) 6 A.1

15、 Introduction 6 A.2 Conformity assessment procedure . 6 A.3 Certification and CE marking 7 A.3.1 Declaration of conformity, CE marking . 7 A.3.2 Notified bodys identification mark and certificate 7 Annex B (informative) Summary of inspection and testing activities 8 Bibliography . 17 PD CEN/TR 13480

16、7:2017CEN/TR 13480-7:2017 (E) 3 European foreword This document (CEN/TR 13480-7:2017) has been prepared by Technical Committee CEN/TC 267 “Industrial piping and pipelines”, the secretariat of which is held by AFNOR. Attention is drawn to the possibility that some of the elements of this document may

17、 be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TR 13480-7:2002. EN 13480, Metallic industrial piping consists of eight interdependent and not dissociable Parts which include: Part 1: Gener

18、al Part 2: Materials Part 3: Design Part 4: Fabrication and installation Part 5: Inspection and testing Part 6: Additional requirements for buried piping CEN/TR 13480-7, Guidance on the use of conformity assessment procedures Part 8: Additional requirements for aluminium and aluminium alloy piping T

19、he significant technical changes between this Technical Report and the previous edition are: a general revision of this document to comply with PED 2014/68/UE; in Table A.1, inclusion of new Modules designation and addition of the Module G ; in sub-clause A.3, revision of the documentation ; in Tabl

20、e B.2, update of cross references for detailed requirements in EN 13480-4:2017 and EN 13480-5:2017. NOTE These technical changes are the significant technical changes but it is not an exhaustive list of all modifications. PD CEN/TR 134807:2017CEN/TR 13480-7:2017 (E) 4 1 Scope This Technical Report g

21、ives guidance on the use of conformity assessment procedures for industrial piping in relation to EN 13480. 2 Normative references Not applicable. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 responsible authority competent organization wh

22、ich is independent of the manufacturer Note 1 to entry: For application within the jurisdiction of the European Union this organization may be a Notified Body or a user inspectorate where appropriate, according to module chosen and designated by a member state. For the purpose of this standard, all

23、these organizations have been collectively termed “responsible authorities”. 3.2 fluid gases, liquids and vapours in pure phase as well as mixtures thereof Note 1 to entry: A fluid may contain a suspension of solids. 4 Application of the PED 4.1 General According to the PED, the manufacturer shall d

24、etermine for each industrial piping and pipeline: a) the category of the industrial piping and pipeline; b) the procedures to be applied to assess conformity of the industrial piping and pipeline with the requirements of the PED. 4.2 Conformity assessment procedures 4.2.1 General The manufacturer sh

25、all subject each item of equipment to a procedure to assess the conformity with the essential requirements of the PED. Annex A describes the conformity assessment requirements of the PED. It is applicable to piping systems which are to be installed in an EU Member State. 4.2.2 Choice of conformity a

26、ssessment procedures The conformity assessment procedures to be applied to an item or pressure equipment with a view to affixing the CE marking shall be determined by the category in which the equipment is classified. The procedures that are to be applied for the various categories are given in Tabl

27、e A.1. The manufacturer has the option of selecting between a procedure of conformity assessment involving a certified quality assurance system (if available) and one which does not. The manufacturer may choose to apply one of the procedures which apply to a higher category. PD CEN/TR 134807:2017CEN

28、/TR 13480-7:2017 (E) 5 4.2.3 Conformity assessment procedures and the involvement of Responsible Authorities The manufacturer is responsible for ensuring that the requirements of this Technical Report, including inspection and testing activities, are fully applied. If a CE marking is sought, it is a

29、 requirement of the PED that (in many cases) there is a supplementary involvement of a Responsible Authority (e.g. Notified Body) to ensure the requirements of the PED are met. The kind and extent of responsible authority involvement in inspection and testing activities will depend upon the conformi

30、ty assessment procedure chosen by the manufacturer. For each appropriate conformity assessment procedure the participation is indicated in Table B.1. Annex B has been provided in order to give guidance to the manufacturer so that he may be aware of the various stages where a responsible authority ma

31、y be involved. Details of the inspection and testing activities are described in subsequent subclauses, the reference of which is given in Table B.1. 5 Subcontracting The manufacturer is responsible for the fabrication and the installation, even if this work will be subcontracted to other fabricator

32、s and/or installers. Where the manufacturer is producing the equipment under a conformity assessment procedure requiring intervention of a responsible authority, the manufacturer shall inform the responsible authority of his intention to subcontract so that the responsible authority has the opportun

33、ity to take part in the subcontractor surveillance. Where the manufacturer is producing the equipment under a conformity assessment procedure based on quality assurance, e.g. D, H, H1, the controls the manufacturer applies over subcontractors shall be described in his appropriate quality system. PD

34、CEN/TR 134807:2017CEN/TR 13480-7:2017 (E) 6 Annex A (informative) Conformity of industrial piping to the essential safety requirements of Directive 2014/68/EU (Pressure equipment directive) A.1 Introduction This annex describes the conformity assessment requirements of Directive 2014/68/EU. It is ap

35、plicable to piping systems which are to be installed in an EU Member State. In the EU Member States, the authorized inspection bodies are identical to the notified bodies. 1)A.2 Conformity assessment procedure Where piping is subject to the conformity assessment procedure, the manufacturer shall ide

36、ntify the appropriate piping category based upon the classification of the piping as defined in EN 13480-1:2017, Table 5.1-1, and subsequently shall select one of the conformity assessment modules available for that piping category in accordance with Table A.1. NOTE The conformity assessment procedu

37、re attributed to a higher category can be applied to piping classified in a lower category. The activities to be performed by the parties involved in each of the conformity assessment procedures during design and fabrication/installation of the piping in accordance with this European Standard are su

38、mmarized in Annex B. Table A.1 Piping categories and conformity assessment modules Category (PED) Category (EN 134801) Conformity assessment module considered in EN 13480 Conformity assessment module not considered in EN 13480 0 III III B (design type)+D, B (design type)+F, H B (production type)+E,

39、B (production type)+C2 II II A2, D1 E1 I I A If the manufacturer selected a module applicable to PED Category IV, the following applies: If module G is selected, the columns for B (design type) and F in Table B.2 shall be used. If module H1 is selected, the columns H (without the requirements DESIGN

40、) and B (design type) in Table B.2 shall be used. 1) For intervention of user inspectorates, see Article 16 of Directive 2014/68/EU (Pressure Equipment Directive).PD CEN/TR 134807:2017CEN/TR 13480-7:2017 (E) 7 A.3 Certification and CE marking A.3.1 Declaration of conformity, CE marking A declaration

41、 of conformity and CE marking (see EN 13480-4) shall be required if piping of Categories I, II and III is placed at a market in a country where the PED applies (see Table A.2). A.3.2 Notified bodys identification mark and certificate Where appropriate, the notified bodys identification number shall

42、be applied adjacent to the CE marking. Under module F, on satisfactory completion of final assessment the notified body shall issue an EC certificate of conformity. Table A.2 Declaration of conformity of final inspection for piping (form) DECLARATION/CERTIFICATE OF CONFORMITY FOR PIPING Description

43、of piping Identification no./drawings no. manufactured by (company) for (plant/purchaser/purpose) Design conditions: PS bar TSmax, TSminC category conformity assessment procedure name, address and number of the notified body Reference to EU type-examination certificate-design type, EU design-examina

44、tion certificate or certificate of conformity as appropriate DECLARATION/ OF DESIGN COMPLIANCE (see EN 134805, Figure A.1) no. /by DECLARATION of COMPLIANCE for FABRICATION, INSTALLATION AND TESTING (see EN 134805, Figure A.2) no./by We hereby declare that the above piping conforms with the requirem

45、ents of the Directive 2014/68/EU (Pressure Equipment Directive) and EN 13480:2017. The fulfilment of the applicable essential safety requirements set out in Annex I of the PED has been demonstrated. Manufacturer Place and Date Name and Function Signature PD CEN/TR 134807:2017CEN/TR 13480-7:2017 (E)

46、8 Annex B (informative) Summary of inspection and testing activities The required involvement of the parties concerned is indicated in Table B.2 by letters in the appropriate conformity assessment columns as follows (see Table B.1 for relations between Actions and Modules): (M) action performed by f

47、abricator, where specified in his manufacturing documents; M action performed by fabricator/installer; M/RAcaction performed by fabricator/installer and checked by responsible authority; M/RAiaction performed by fabricator/installer and monitored by responsible authority. Amount depends on complexit

48、y and familiarity of the piping fabricator/installer with that type of piping manufacture and the knowledge and experience of the responsible authority with the manufacturer; M/RAmaction performed by fabricator/installer and monitored by responsible authority during visits within the quality system.

49、 Amount depends on complexity and familiarity of the piping fabricator/installer with that type of piping manufacture and the knowledge and experience of the responsible authority with the manufacturers quality system; M/RAqaction performed by fabricator/installer and checked by responsible authority during assessment of quality system/type examination; RA action performed by responsible authority. Table B.1 Relation between Actions and Modules Action Typically applied for Modules M all Modules M/RAcB