CAN CSA-ISO IEC TR 18047-3-2013 Information technology - Radio frequency identification device conformance test methods - Part 3 Test methods for air interface communications below.pdf

《CAN CSA-ISO IEC TR 18047-3-2013 Information technology - Radio frequency identification device conformance test methods - Part 3 Test methods for air interface communications below.pdf》由会员分享，可在线阅读，更多相关《CAN CSA-ISO IEC TR 18047-3-2013 Information technology - Radio frequency identification device conformance test methods - Part 3 Test methods for air interface communications below.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、Information technology Radio frequency identification device conformance test methods Part 3: Test methods for air interface communications below 13,56 kHzCAN/CSA-ISO/IEC TR 18047-3:13(ISO/IEC TR 18047-3:2011, IDT)National Standard of CanadaNOT FOR RESALE. / PUBLICATION NON DESTINE LA REVENTE.Legal

2、Notice for StandardsCanadian Standards Association (operating as “CSA Group”) develops standards through a consensus standards development process approved by the Standards Council of Canada. This process brings together volunteers representing varied viewpoints and interests to achieve consensus an

3、d develop a standard. Although CSA Group administers the process and establishes rules to promote fairness in achieving consensus, it does not independently test, evaluate, or verify the content of standards.Disclaimer and exclusion of liabilityThis document is provided without any representations,

4、warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual property rights. CSA Group does

5、not warrant the accuracy, completeness, or currency of any of the information published in this document. CSA Group makes no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation. IN NO EVENT SHALL CSA GROUP, ITS VOLUNTEERS, MEMBERS, SUBSI

6、DIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAM

7、AGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF CSA GROUP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJU

8、RY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, CSA Group is not undertaking to render professional or other services for or on behalf of any person or entity or to perform any duty owed by any person or entity to another person or entity. The information in this docum

9、ent is directed to those who have the appropriate degree of experience to use and apply its contents, and CSA Group accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained in this document. CSA Group is a private not-for-profit company

10、 that publishes voluntary standards and related documents. CSA Group has no power, nor does it undertake, to enforce compliance with the contents of the standards or other documents it publishes. Intellectual property rights and ownershipAs between CSA Group and the users of this document (whether i

11、t be in printed or electronic form), CSA Group is the owner, or the authorized licensee, of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary), and all inventions and trade secrets that may be contained in this document, whether or

12、 not such inventions and trade secrets are protected by patents and applications for patents. Without limitation, the unauthorized use, modification, copying, or disclosure of this document may violate laws that protect CSA Groups and/or others intellectual property and may give rise to a right in C

13、SA Group and/or others to seek legal redress for such use, modification, copying, or disclosure. To the extent permitted by licence or by law, CSA Group reserves all intellectual property rights in this document.Patent rightsAttention is drawn to the possibility that some of the elements of this sta

14、ndard may be the subject of patent rights. CSA Group shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility.Authorized use of this docu

15、mentThis document is being provided by CSA Group for informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form:sLOADTHISDOCUMENTONTOACOMPUTERFORTHESOLEPURPOSEOFREVIEWINGITsSEARCHANDBROWSETHISDOCUMENTANDsPRINTTHI

16、SDOCUMENTIFITISIN0$ this remains the continuing responsibility of the SDO. An NSC reflects a consensus of a number of capable individuals whose collective interests provide, to the greatest practicable extent, a balance of representation of general interests, producers, regulators, users (including

17、consumers), and others with relevant interests, as may be appropriate to the subject in hand. It normally is a standard which is capable of making a significant and timely contribution to the national interest.Those who have a need to apply standards areencouraged to use NSCs. These standards are su

18、bjectto periodic review. Users of NSCs are cautionedto obtain the latest edition from the SDO which publishes the standard.The responsibility for approving standards as National Standards of Canada rests with theStandards Council of Canada270 Albert Street, Suite 200Ottawa, Ontario, K1P 6N7CanadaAlt

19、hough the intended primary application of this Standard is stated in its Scope, it is importantto note that it remains the responsibility of the users to judge its suitability for their particular purpose.Registered trade-mark of Canadian Standards AssociationCette norme est offerte en anglais seule

20、ment pour le moment. Le Groupe CSA publiera la versionen franais ds quelle sera produite par lorganisme rdacteur.TMA trade-mark of the Canadian Standards Association, operating as “CSA Group”National Standard of CanadaPublished in January 2013 by CSA GroupA not-for-profit private sector organization

21、5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N61-800-463-6727 416-747-4044Visit our Online Store at shop.csa.caApproved byStandards Council of CanadaCAN/CSA-ISO/IEC TR 18047-3:13Information technology Radio frequency identification device conformance test methods Part 3: Test meth

22、ods for air interface communications below 13,56 kHzPrepared by InternationalOrganizationforStandardization/ International Electrotechnical CommissionReviewed byCAN/CSA-ISO/IEC TR 18047-3:13Information technology Radio frequency identificationdevice conformance test methods Part 3: Test methodsfor a

23、ir interface communications below 13,56 kHzCSA/4 2013 CSA Group January 2013CAN/CSA-ISO/IEC TR 18047-3:13Information technology Radio frequency identification device conformance test methods Part 3: Test methods for air interface communications below 13,56 kHzCSA PrefaceStandards development within

24、the Information Technology sector is harmonized with international standards development. Through the CSA Technical Committee on Information Technology (TCIT), Canadians serve as the Canadian Advisory Committee (CAC) on ISO/IEC Joint Technical Committee 1 on Information Technology (ISO/IEC JTC1) for

25、 the Standards Council of Canada (SCC), the ISO member body for Canada and sponsor of the Canadian National Committee of the IEC. Also, as a member of the International Telecommunication Union (ITU), Canada participates in the International Telegraph and Telephone Consultative Committee (ITU-T).This

26、 Standard supersedes CAN/CSA-ISO/IEC TR 18047-3-05 (adoption of ISO/IEC TR 18047-3:2004).At the time of publication, ISO/IEC TR 18047-3:2011 is available from ISO and IEC in English only. CSA Group will publish the French version when it becomes available from ISO and IEC.This International Standard

27、 was reviewed by the TCIT under the jurisdiction of the Strategic Steering Committee on Information Technology and deemed acceptable for use in Canada. From time to time, ISO/IEC may publish addenda, corrigenda, etc. The TCIT will review these documents for approval and publication. For a listing, r

28、efer to the Current Standards Activities page at standardsactivities.csa.ca. This Standard has been formally approved, without modification, by the Technical Committee and has been approved as a National Standard of Canada by the Standards Council of Canada. 2013 CSA GroupAll rights reserved. No par

29、t of this publication may be reproduced in any form whatsoever without the prior permission of thepublisher. ISO/IEC material is reprinted with permission. Where the words “this Technical Report” appear in the text, they should be interpreted as “this National Standard of Canada”.Inquiries regarding

30、 this National Standard of Canada should be addressed toCSA Group5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N61-800-463-6727 416-747-4000http:/csa.caTo purchase standards and related publications, visit our Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-

31、4044.This Standard is subject to periodic review, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the following information to inquiriescsagroup.org and include “Proposal for change” in the subject line:(a) Standard desi

32、gnation (number);(b) relevant clause, table, and/or figure number;(c) wording of the proposed change; and(d) rationale for the change.Reference numberISO/IEC TR 18047-3:2011(E)ISO/IEC 2011TECHNICAL REPORT ISO/IECTR18047-3Second edition2011-06-01Information technology Radio frequency identification d

33、evice conformance test methods Part 3: Test methods for air interface communications at 13,56 MHz Technologies de linformation Mthodes dessai de conformit du dispositif didentification de radiofrquence Partie 3: Mthodes dessai pour des communications dune interface dair 13,56 MHz ISO/IEC TR 18047-3:

34、2011(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at t

35、he address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org ii ISO/IEC 2011 All rights reservedISO/IEC TR 18047-3:2011(E) ISO/IEC 2011 All rights rese

36、rved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Symbols and abbreviated terms 2 5 Conformance tests for ISO/IEC 18000-3 13,56 MHz 3 5.1 General .3 5.2 Default conditions applicable to the test methods 3 5.2.1 Test environment.3 5.2.2 Pre

37、-conditioning 3 5.2.3 Default tolerance .3 5.2.4 Spurious inductance .3 5.2.5 Total measurement uncertainty .3 5.3 Conformance tests for ISO/IEC 18000-3 Mode 1 3 5.3.1 General .3 5.3.2 Test apparatus and test circuits 3 5.3.3 Functional test tag7 5.3.4 Functional test interrogator.8 5.4 Conformance

38、tests for ISO/IEC 18000-3 Mode 2 10 5.4.1 General .10 5.4.2 Test apparatus and test circuits 10 5.4.3 Functional test tag11 5.4.4 Functional test interrogator.12 5.5 Conformance tests for ISO/IEC 18000-3 Mode 3 (mandatory ASK part)13 5.5.1 General .13 5.5.2 Test apparatus and test circuits 13 5.5.3

39、Functional test tag17 5.5.4 Functional test interrogator.18 Annex A (normative) Test setup parameters and dimensions for tags smaller than or equal to an ISO/IEC 7810 ID-1 outline20 Annex B (normative) Guideline for RFID tags larger than ISO/IEC 7810 ID-1 size.23 Annex C (normative) Test interrogato

40、r antenna27 Annex D (informative) Test interrogator antenna tuning 30 Annex E (normative) Sense coil 32 Annex F (normative) Reference tag for interrogator power test34 Annex G (informative) Reference tag for load modulation test36 Annex H (informative) Program for evaluation of the spectrum 37 Bibli

41、ography41 ISO/IEC TR 18047-3:2011(E) iv ISO/IEC 2011 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC

42、participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, govern

43、mental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Par

44、t 2. In exceptional circumstances, when the joint technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example), it may decide to publish a Technical Report. A Technical Report is entirely informative i

45、n nature and shall be reviewed every five years in the same manner as an International Standard. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent righ

46、ts. ISO/IEC TR 18047-3, was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 31, Automatic identification and data capture techniques. This second edition cancels and replaces the first edition (ISO/IEC TR 18047-3:2004), which has been technically revised.

47、 It also incorporates the Technical Corrigendum ISO/IEC TR 18047-3:2004/Cor.1:2007. ISO/IEC TR 18047 consists of the following parts, under the general title Information technology Radio frequency identification device conformance test methods: Part 2: Test methods for air interface communications b

48、elow 135 kHz Part 3: Test methods for air interface communications at 13,56 MHz Part 4: Test methods for air interface communications at 2,45 GHz Part 6: Test methods for air interface communications at 860 MHz to 960 MHz Part 7: Test methods for active air interface communications at 433 MHz ISO/IE

49、C TR 18047-3:2011(E) ISO/IEC 2011 All rights reserved vIntroduction ISO/IEC 18000 defines the air interfaces for radio frequency identification (RFID) devices used in item management applications. ISO/IEC 18000-3 defines the air interface for these devices operating in the 13,56 MHz Industrial, Scientific, and M