BS ISO 7755-3-2013 Hardmetal burrs Cylindrical round- (ball-) nose burrs (style C)《硬质合金毛刺刀 圆锥形 (球形) 刀尖毛刺刀 (C型)》.pdf

《BS ISO 7755-3-2013 Hardmetal burrs Cylindrical round- (ball-) nose burrs (style C)《硬质合金毛刺刀 圆锥形 (球形) 刀尖毛刺刀 (C型)》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7755-3-2013 Hardmetal burrs Cylindrical round- (ball-) nose burrs (style C)《硬质合金毛刺刀 圆锥形 (球形) 刀尖毛刺刀 (C型)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 7755-3:2013Hardmetal burrsPart 3: Cylindrical round- (ball-) nose burrs(style C)BS ISO 7755-3:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 7755-3:2013.The UK participation in its preparation was entrusted to TechnicalComm

2、ittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The

3、 British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 80970 5ICS 25.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 Au

4、gust 2013.Amendments issued since publicationDate Text affectedBS ISO 7755-3:2013 ISO 2013Hardmetal burrs Part 3: Cylindrical round- (ball-) nose burrs (style C)Fraises-limes en mtaux-durs Partie 3: Fraises-limes cylindriques bout rond (forme C)INTERNATIONAL STANDARDISO7755-3Second edition2013-08-15

5、Reference numberISO 7755-3:2013(E)BS ISO 7755-3:2013ISO 7755-3:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or me

6、chanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01

7、 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 7755-3:2013ISO 7755-3:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 1Annex A (informative) Relationship between designations in this part o

8、f ISO 7755 and the ISO 13399 series . 2Bibliography 3BS ISO 7755-3:2013ISO 7755-3:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out

9、through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO coll

10、aborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approv

11、al criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject o

12、f patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used

13、in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This second edition cancels and replaces the fir

14、st edition (ISO 7755-3:1984), of which it constitutes a minor revision.ISO 7755 consists of the following parts, under the general title Hardmetal burrs: Part 1: General specifications Part 2: Cylindrical burrs (style A) Part 3: Cylindrical round- (ball-) nose burrs (style C) Part 4: Spherical burrs

15、 (style D) Part 5: Oval burrs (style E) Part 6: Arch round- (ball-) nose burrs (style F) Part 7: Arch pointed-nose burrs (style G) Part 8: Flame burrs (style H) Part 9: 60 and 90 cone burrs (styles J and K) Part 10: Conical round- (ball-) nose burrs (style L) Part 11: Conical pointed-nose burrs (sty

16、le M) Part 12: Inverted cone burrs (style N)iv ISO 2013 All rights reservedBS ISO 7755-3:2013INTERNATIONAL STANDARD ISO 7755-3:2013(E)Hardmetal burrs Part 3: Cylindrical round- (ball-) nose burrs (style C)1 ScopeThis part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal bu

17、rrs of cylindrical shape, with a round- (ball-) nose and designated by the symbol C.Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.2 Normative referencesThe following documents, in who

18、le or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 7755-1, Hardmetal burrs Part 1: Gen

19、eral specifications3 DimensionsSee Figure 1 and Table 1. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are specified in ISO 7755-1.dlFigure 1 Hardmetal burr, style CTable 1 DimensionsDimensions in millimetresd l2

20、 103 134 136 168 2010 2012 2516 25 ISO 2013 All rights reserved 1BS ISO 7755-3:2013ISO 7755-3:2013(E)Annex A (informative) Relationship between designations in this part of ISO 7755 and the ISO 13399 seriesFor the relationship between designations in this part of ISO 7755 and preferred symbols accor

21、ding to the ISO 13399 series, see Table A.1.Table A.1 Relationship between designations in this part of ISO 7755 and the ISO 13399 seriesSymbol in this part of ISO 7755 (ISO 7755-3)Reference in this part of ISO 7755 (ISO 7755-3)Property name in the ISO 13399 seriesSymbol in the ISO 13399 seriesRefer

22、ence in the ISO 13399 seriesd Clause 3 Cutting diameter DC ISO/TS 13399-3 71E57Fl Clause 3 Cutting edge length L ISO/TS 13399-3 71DD6C95DA49B2 ISO 2013 All rights reservedBS ISO 7755-3:2013ISO 7755-3:2013(E)Bibliography1 ISO 13399 (all parts), Cutting tool data representation and exchange ISO 2013 A

23、ll rights reserved 3BS ISO 7755-3:2013ISO 7755-3:2013(E) ISO 2013 All rights reservedICS 25.100.20Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is inco

24、rporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and o

25、thers to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to

26、help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download

27、 PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our

28、Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and internatio

29、nal standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing

30、 Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Networ

31、k Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and

32、other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, softw

33、are and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for

34、commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Deta

35、ils and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW