BS ISO 7755-2-2013 Hardmetal burrs Cylindrical burrs (style A)《硬质合金去毛刺锉 圆柱形锉(A款)》.pdf

《BS ISO 7755-2-2013 Hardmetal burrs Cylindrical burrs (style A)《硬质合金去毛刺锉 圆柱形锉(A款)》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7755-2-2013 Hardmetal burrs Cylindrical burrs (style A)《硬质合金去毛刺锉 圆柱形锉(A款)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 7755-2:2013Hardmetal burrsPart 2: Cylindrical burrs (style A)BS ISO 7755-2:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 7755-2:2013.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools

2、 tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards

3、Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 80969 9ICS 25.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2013.Amendment

4、s issued since publicationDate Text affectedBS ISO 7755-2:2013 ISO 2013Hardmetal burrs Part 2: Cylindrical burrs (style A)Fraises-limes en mtaux-durs Partie 2: Fraises-limes cylindriques (forme A)INTERNATIONAL STANDARDISO7755-2Second edition2013-08-15Reference numberISO 7755-2:2013(E)BS ISO 7755-2:2

5、013ISO 7755-2:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on t

6、he internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWe

7、b www.iso.orgPublished in SwitzerlandBS ISO 7755-2:2013ISO 7755-2:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 1Annex A (informative) Relationship between designations in this part of ISO 7755 and the ISO 13399 series . 2Bibliograp

8、hy 3BS ISO 7755-2:2013ISO 7755-2:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bod

9、y interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrote

10、chnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO

11、 documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsibl

12、e for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the con

13、venience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This second edition cancels and replaces the first edition (ISO 7755-2:1984), of which it constit

14、utes a minor revision.ISO 7755 consists of the following parts, under the general title Hardmetal burrs: Part 1: General specifications Part 2: Cylindrical burrs (style A) Part 3: Cylindrical round- (ball-) nose burrs (style C) Part 4: Spherical burrs (style D) Part 5: Oval burrs (style E) Part 6: A

15、rch round- (ball-) nose burrs (style F) Part 7: Arch pointed-nose burrs (style G) Part 8: Flame burrs (style H) Part 9: 60 and 90 cone burrs (styles J and K) Part 10: Conical round- (ball-) nose burrs (style L) Part 11: Conical pointed-nose burrs (style M) Part 12: Inverted cone burrs (style N)iv IS

16、O 2013 All rights reservedBS ISO 7755-2:2013INTERNATIONAL STANDARD ISO 7755-2:2013(E)Hardmetal burrs Part 2: Cylindrical burrs (style A)1 ScopeThis part of ISO 7755 specifies the main dimensions of the cutting part for hardmetal burrs of cylindrical shape and designated by the symbol A.Tolerances on

17、 the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicat

18、ion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 7755-1, Hardmetal burrs Part 1: General specifications3 DimensionsSee Figure 1 and Table 1. Tolerances on the cutting diameter, dire

19、ction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are specified in ISO 7755-1.dlFigure 1 Hardmetal burr, style ATable 1 DimensionsDimensions in millimetresd l2 103 134 136 168 2010 2012 2516 25 ISO 2013 All rights reserved 1BS ISO 7755-2:2013ISO 7755-2:201

20、3(E)Annex A (informative) Relationship between designations in this part of ISO 7755 and the ISO 13399 seriesFor the relationship between designations in this part of ISO 7755 and preferred symbols according to the ISO 13399 series, see Table A.1.Table A.1 Relationship between designations in this p

21、art of ISO 7755 and the ISO 13399 seriesSymbol in this part of ISO 7755 (ISO 7755-2)Reference in this part of ISO 7755 (ISO 7755-2)Property name in the ISO 13399 seriesSymbol in the ISO 13399 seriesReference in the ISO 13399 seriesd Clause 3 Cutting diameter DC ISO/TS 13399-3 71E57Fl Clause 3 Cuttin

22、g edge length L ISO/TS 13399-3 71DD6C95DA49B2 ISO 2013 All rights reservedBS ISO 7755-2:2013ISO 7755-2:2013(E)Bibliography1 ISO 13399 (all parts), Cutting tool data representation and exchange ISO 2013 All rights reserved 3BS ISO 7755-2:2013ISO 7755-2:2013(E) ISO 2013 All rights reservedICS 25.100.2

23、0Price based on 3 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by

24、BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowle

25、dge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that

26、your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international stand

27、ards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using

28、 standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up

29、to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically

30、 receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover

31、 as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of ou

32、r products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the propert

33、y of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act

34、1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW