BS ISO 7510-2017 Plastics piping systems Glass-reinforced plastics (GRP) components Determination of the amounts of constituents《塑料管道系统 玻璃钢部件 成分含量的测定》.pdf

《BS ISO 7510-2017 Plastics piping systems Glass-reinforced plastics (GRP) components Determination of the amounts of constituents《塑料管道系统 玻璃钢部件 成分含量的测定》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7510-2017 Plastics piping systems Glass-reinforced plastics (GRP) components Determination of the amounts of constituents《塑料管道系统 玻璃钢部件 成分含量的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Plastics piping systems Glass-reinforced plastics (GRP) components Determination of the amounts of constituentsBS ISO 7510:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Plastics piping systems Glass-reinforced plastics (GRP) components Determination of

2、 the amounts of constituentsSystmes de canalisations en matires plastiques Composants plastiques renforcs de verre (PRV) Dtermination des teneurs des constituantsINTERNATIONAL STANDARDISO7510Second edition2017-06Reference numberISO 7510:2017(E)National forewordThis British Standard is the UK impleme

3、ntation of ISO 7510:2017.The UK participation in its preparation was entrusted to Technical Committee PRI/88/2, Plastics piping for pressure applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all

4、 the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 84876 6ICS 23.040.45; 23.040.20Compliance with a British Standard cannot confer immunity from legal obligations.Thi

5、s British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS ISO 7510:2017 ISO 2017Plastics piping systems Glass-reinforced plastics (GRP) components Determinatio

6、n of the amounts of constituentsSystmes de canalisations en matires plastiques Composants plastiques renforcs de verre (PRV) Dtermination des teneurs des constituantsINTERNATIONAL STANDARDISO7510Second edition2017-06Reference numberISO 7510:2017(E)BS ISO 7510:2017ISO 7510:2017(E)ii ISO 2017 All righ

7、ts reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or

8、an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.

9、orgwww.iso.orgBS ISO 7510:2017ISO 7510:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or

10、mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva,

11、 SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 7510:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Principle 15 Apparatus . 26 Test piece 26.1 Dimensions . 26.2 Number 37 Procedure. 38 Calculation and expression of results . 49

12、Test report . 4Bibliography 5 ISO 2017 All rights reserved iiiContents PageBS ISO 7510:2017ISO 7510:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is nor

13、mally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in

14、the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular th

15、e different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this do

16、cument may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso

17、 .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as inform

18、ation about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids

19、, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications.This second edition cancels and replaces the first edition (ISO 7510:1997), which has been technically revised.The main changes compared to the previous edition are as follows: modified the title; clarified accuracy sta

20、tements; eliminated specific sample size; referenced ISO 3126 for dimension determination; allowed use of test specimens taken from mechanical property test samples.iv ISO 2017 All rights reservedBS ISO 7510:2017ISO 7510:2017(E)ForewordISO (the International Organization for Standardization) is a wo

21、rldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented o

22、n that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this

23、document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Dire

24、ctives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the dev

25、elopment of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary n

26、ature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This

27、 document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications.This second edition cancels and replaces the first edition (ISO 7510:1997), which has been technic

28、ally revised.The main changes compared to the previous edition are as follows: modified the title; clarified accuracy statements; eliminated specific sample size; referenced ISO 3126 for dimension determination; allowed use of test specimens taken from mechanical property test samples.iv ISO 2017 Al

29、l rights reserved INTERNATIONAL STANDARD ISO 7510:2017(E)Plastics piping systems Glass-reinforced plastics (GRP) components Determination of the amounts of constituents1 ScopeThis document specifies a method for the determination of constituent materials of a test sample cut from a glass-reinforced

30、plastics (GRP) component intended for use in a piping system. It includes determination of resin, glass, aggregate and filler contents.It is also applicable to the determination of the type and arrangement of the reinforcements. If used to determine the amounts of constituent materials in layered co

31、nstructions it may be necessary to separate the laminate layers by cutting or splitting and testing each separately.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated reference

32、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3126, Plastics piping systems Plastics components Determination of dimensions3 Terms and definitionsNo terms and definitions are listed in this document. IS

33、O and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 PrincipleA test piece of known size and mass is ignited to bu

34、rn off the resin, and the residue analysed by separating and weighing the constituents loss on ignition (LOI) is a common term for such testing. If the construction includes organic reinforcements, such as surfacing veils, or processing aids, such as thermoplastic mesh or filaments, these will be bu

35、rned off with the resin. Typically such materials if used are in small amounts and will not introduce significant error in the determination of raw material contents. Also, organic materials used in glass fibre reinforcement sizing or binder will be burned off. The amounts of such materials are very

36、 small.NOTE 1 In the case of filled laminates, especially those containing fillers of small particle size (including thixotropic agents), accurate analysis of the constituents can prove difficult. This is because of the difficulty in separating such fillers from the other constituents and the risk o

37、f some filler being lost during combustion.This test method can be used to determine and monitor the fibre architecture of the laminate layers used in the piping component.NOTE 2 It is assumed that the following testing parameters are set by the referring standard:a) whether or not the types of glas

38、s fibre reinforcement in the constituent layers is to be determined;b) whether or not the glass content of each layer is to be determined; ISO 2017 All rights reserved 1BS ISO 7510:2017ISO 7510:2017(E)c) whether or not the aggregate and filler contents are to be determined, and whether to do so for

39、each layer.This document is used to measure and describe the behaviour of composite material to heat under controlled conditions, but does not by itself incorporate all the factors required for fire hazard or fire assessments of the composite materials under actual fire conditions. Fire testing is i

40、nherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user to consult and establish appropriate safety and

41、 health practices in accordance with national regulations prior to use.This test method does not apply to constructions that contain reinforcement materials that lose weight under the conditions of test or contain resins that do not decompose. The content of fillers that decompose under the conditio

42、ns of test cannot be determined by this method and alternate procedures shall be employed.5 ApparatusThe usual laboratory apparatus and, in particular, the following.5.1 Crucible, of a suitable material and dimensions.5.2 Oven, capable of maintaining a temperature of 105 C to 110 C.5.3 Electric muff

43、le furnace, or microwave furnace, capable of maintaining a temperature of 625 C 20 C or a temperature between 500 C and 600 C to an accuracy of 20 C.5.4 Bunsen burner or similar.5.5 Desiccator.5.6 Balance, calibrated to an accuracy of 1 mg.5.7 Measuring devices calibrated to an accuracy of 0,05 mm.5

44、.8 Sieves, of suitable mesh, as needed to separate fillers and aggregate.5.9 Spatulas, tweezers and sieves, as needed to separate constituent materials.6 Test piece6.1 DimensionsThe test piece shall comprise the full thickness of the component from which the test piece was taken, unless individual l

45、ayers are being investigated. The test piece shall have smooth edges and be free from dust. If reinforcement materials are to be classified by weight per unit area, then the test piece shall be rectangular.The recommended sample size for components up to 30 mm wall thickness is approximately 40 mm 4

46、0 mm multiplied by the thickness of the component. For components with a wall thickness exceeding 30 mm, samples of approximately 40 mm 10 mm multiplied by the thickness of the component have been found acceptable. Other sample sizes are permitted by agreement.Dimensional measurements as needed shal

47、l be in accordance with ISO 3126.2 ISO 2017 All rights reservedBS ISO 7510:2017ISO 7510:2017(E)c) whether or not the aggregate and filler contents are to be determined, and whether to do so for each layer.This document is used to measure and describe the behaviour of composite material to heat under

48、 controlled conditions, but does not by itself incorporate all the factors required for fire hazard or fire assessments of the composite materials under actual fire conditions. Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these

49、tests. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user to consult and establish appropriate safety and health practices in accordance with national regulations prior to use.This test method does not apply to constructions that contain reinforcement materials that lose weight under the conditions of test or contain resins that do not decompose. The content of fillers that decompose under the cond