BS ISO 6519-2015 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs《柴油机 喷油泵 轴端和毂盘的锥度》.pdf

《BS ISO 6519-2015 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs《柴油机 喷油泵 轴端和毂盘的锥度》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6519-2015 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs《柴油机 喷油泵 轴端和毂盘的锥度》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 6519:2015Diesel engines Fuel injectionpumps Tapers for shaft endsand hubsBS ISO 6519:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6519:2015. Itsupersedes BS ISO 6519:2004 which is withdrawn.The UK participation in its pre

2、paration was entrusted to TechnicalCommittee MCE/22, Engines for road vehicles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correc

3、tapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 83388 5ICS 43.060.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy C

4、ommittee on 31 July 2015.Amendments issued since publicationDate Text affectedBS ISO 6519:2015 ISO 2015Diesel engines Fuel injection pumps Tapers for shaft ends and hubsMoteurs diesels Pompes dinjection de combustible Cnes pour bouts darbre et moyeuxINTERNATIONAL STANDARDISO6519Fourth edition2015-08

5、-15Reference numberISO 6519:2015(E)BS ISO 6519:2015ISO 6519:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any

6、means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-

7、1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 6519:2015ISO 6519:2015(E)Foreword iv1 Scope . 12 Dimensions and tolerances . 12.1 General . 12.2 Shaft ends with taper 12.3 Keyways of hub with taper . 1 ISO 2015 All rights reserved iiiConten

8、ts PageBS ISO 6519:2015ISO 6519:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

9、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec

10、hnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO

11、documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held respo

12、nsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given

13、for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following U

14、RL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 34, Propulsion, powertrain, and powertrain fluids.This fourth edition cancels and replaces the third edition (ISO 6519:2004), which has been technically revised.iv ISO 201

15、5 All rights reservedBS ISO 6519:2015INTERNATIONAL STANDARD ISO 6519:2015(E)Diesel engines Fuel injection pumps Tapers for shaft ends and hubs1 ScopeThis International Standard specifies the dimensions of tapered shaft ends and hubs of fuel injection pumps and common-rail high pressure pumps for die

16、sel (compression-ignition) engines.The specified shaft ends and hubs may be used with or without Woodruff keys.NOTE The specified shaft ends and hubs can also be used for other applications where no specific standards exist.2 Dimensions and tolerances2.1 GeneralTo ensure satisfactory operation of th

17、e taper drive, it is necessary for manufacturers to provide such cone angle tolerances that the contact between the male and female cones commences at the major diameter.2.2 Shaft ends with taperShaft ends shall be as shown in Figure 1 and Table 1 or Figure 2 and Table 2. The shaft ends taper and th

18、read (Figure 1) may be made optionally according to type 1 or 2. However, it shall be possible to screw the go-gauge for the thread up to the XX line for both these types.Type 3 is a configuration with the thread inside of the taper. This configuration saves space and avoids the critical interface b

19、etween the taper and the thread of the configuration type 1 or 2.2.3 Keyways of hub with taperHub keyways shall be as shown in Figure 3 and Table 3. The length of the hub cone shall be such that, after assembling, the face at the smaller diameter of the hub cone lies so far in front of the XX line (

20、see Figure 1 and Figure 2) that the fixing nut can be correctly screwed up.Dimensions in millimetresa) Type 1 ISO 2015 All rights reserved 1BS ISO 6519:2015ISO 6519:2015(E)b) Type 2Figure 1 Shaft ends type 1 and type 2Table 1 Shaft ends type 1 and type 2Dimensions in millimetresdanom.d1l1max.l20-1t1

21、max.b(h9)17 M12 1,75 14,5 18 1,6 300250,20 M14 1,512 152 40030,16,5 2022M14 1,5 16,520 2 40030,M16 1,5b1823 M16 1,5 18 23 2 40030,25 M18 1,51525 2,6 50030,2030 M20 1,5 23 30 2,6 50030,35 M24 1,519272,6 50030,2727 3540 M30 1,5 27272,6 50030,40aThe tolerance for dimension d depends on the type of shaf

22、t bearing.bThe thread M16 1,5 is preferred for shaft ends with 22 mm diameter.2 ISO 2015 All rights reservedBS ISO 6519:2015ISO 6519:2015(E)Key1 internal thread2 clamping collar (for manufacturing purposes only, no function at the engine)aNominal.Figure 2 Shaft end type 3Table 2 Shaft end type 3Dime

23、nsions in millimetresdanom.d1l1min.l20-1l3b(h9)h25 M12 1 22 25 19,75 40030,9,45aThe tolerance for dimension d depends on the type of shaft bearing.aNominal.Figure 3 Hub ISO 2015 All rights reserved 3BS ISO 6519:2015ISO 6519:2015(E)Table 3 HubDimensions in millimetresdanom.t2min.b(D10)17 1,8 3+002006

24、,20 2,2 4+00300078,22 2,2 4+00300078,23 2,2 4+00300078,25 2,8 (4 or 5)+00300078,30 2,8 5+00300078,35 2,8 5+00300078,40 2,8 5+00300078,ad is the nominal diameter of the shaft.4 ISO 2015 All rights reservedBS ISO 6519:2015BS ISO 6519:2015ISO 6519:2015(E) ISO 2015 All rights reservedICS 43.060.40Price

25、based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Sta

26、ndards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge emb

27、odied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your or

28、ganization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, t

29、hrough our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standa

30、rds easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date

31、. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receiv

32、e the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few

33、 or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our produ

34、cts and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of an

35、d copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no

36、 extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW