BS ISO 5414-1-2002 Tool chucks (end mill holders) with clamp screws for flatted cylindrical shank tools - Dimensions of the driving system of tool shanks《扁方筒形柄刀具用的带卡箍螺钉的刀具卡盘(立铣刀刀具卡.pdf

《BS ISO 5414-1-2002 Tool chucks (end mill holders) with clamp screws for flatted cylindrical shank tools - Dimensions of the driving system of tool shanks《扁方筒形柄刀具用的带卡箍螺钉的刀具卡盘(立铣刀刀具卡.pdf》由会员分享，可在线阅读，更多相关《BS ISO 5414-1-2002 Tool chucks (end mill holders) with clamp screws for flatted cylindrical shank tools - Dimensions of the driving system of tool shanks《扁方筒形柄刀具用的带卡箍螺钉的刀具卡盘(立铣刀刀具卡.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 5414-1:2002 Tool chucks (end mill holders) with clamp screws for flatted cylindrical shank tools Part 1: Dimensions of the driving system of tool shanks ICS 25.060.20 BS ISO 5414-1:2002 This British Standard, having been prepared under the direction of the Engineering Sector

2、Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 19 November 2002 BSI 19 November 2002 ISBN 0 580 40755 1 National foreword This British Standard reproduces verbatim ISO 5414-1:2002 and implements it as the UK national standard. It su

3、persedes BS 6386-1:1986 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/5, Engineers rotary cutting tools of high speed steel, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its

4、 secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or

5、 of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text

6、; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cove

7、r, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 5 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 5414-1:2002(E)IN

8、TERNATIONAL STANDARD ISO 5414-1 Third edition 2002-11-01 Tool chucks (end mill holders) with clamp screws for flatted cylindrical shank tools Part 1: Dimensions of the driving system of tool shanks Mandrins porte-outils, vis de blocage, pour outils queue cylindrique mplat Partie 1: Dimensions du sys

9、tme dentranement des queues doutils BSISO54141:2002BSISO54141:2002iiIS-4145 O1:(2002)E I SO 2002 All irthgs ersedevr iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International St

10、andards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also

11、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committee

12、s is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possib

13、ility that some of the elements of this part of ISO 5414 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 5414-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2, Drills, reamers, milling cutters an

14、d milling machines accessories. This third edition cancels and replaces the second edition (ISO 5414-1:1985), which has been technically revised (in particular by the addition of shanks with diameters 14 mm and 18 mm, and of dimension l 4 ). ISO 5414 consists of the following parts, under the genera

15、l title Tool chucks (end mill holders) with clamp screws for flatted cylindrical shank tools: Part 1: Dimensions of the driving system of tool shanks Part 2: Connecting dimensions of chucks and designation BSISO54141:2002iiiINTENRATIONAL TSANDADR IS-4145 O1:(2002)EI SO 2002 All irthgs ersedevr 1Tool

16、 chucks (end mill holders) with clamp screws for flatted cylindrical shank tools Part 1: Dimensions of the driving system of tool shanks 1 Scope This part of ISO 5414 lays down the dimensions of tool chucks (end mill holders) with clamp screws designed for driving flatted cylindrical shanks in accor

17、dance with ISO 3338-2 and specifies the clamp screws used. It also gives the maximum diameter of the chuck nose. This part of ISO 5414 defines two types of drive: chucks with bores of d 1u 20 mm intended for driving cylindrical shank tools with a single flat, these tools being provided with either a

18、 single or a double cutting part; chucks with bores of d 1W 25 mm intended for driving cylindrical shank tools with a double flat, these tools being provided with a single cutting part only. NOTE The connecting dimensions of the various types of chucks and the designation of tool chucks (end mill ho

19、lders) with clamp screws are dealt with in ISO 5414-2. 2 Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this part of ISO 5414. For dated references, subsequent amendments to, or revisions of, any of these publi

20、cations do not apply. However, parties to agreements based on this part of ISO 5414 are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. M

21、embers of ISO and IEC maintain registers of currently valid International Standards. ISO 3338-2, Cylindrical shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanks BSISO54141:20021IS-4145 O1:(2002)E 2 I SO 2002 All irthgs ersedevr3 Dimensions 3.1 Chucks for tool

22、 shanks with single flat See Figure 1 and Table 1. Figure 1 Table 1 Dimensions in millimetres d 1H5 l 1 1 l 201 l 4min. d 2min. d 36H d 50 1 6 35 18 37 25 M6 15 8 35 18 37 28 M8 20 10 39 20 41 35 M10 25 12 44 22,5 46 42 M12 30 14 44 22,5 46 44 M12 32 16 47 24 49 48 M14 36 18 47 24 49 50 M14 38 20 49

23、 25 51 52 M16 40 BSISO54141:20022IS-4145 O1:(2002)E I SO 2002 All irthgs ersedevr 33.2 Chucks for tool shanks with double flat See Figure 2 and Table 2. Figure 2 Table 2 Dimensions in millimetres d 1H5 l 1 1 l 20 1 l 3 0,5 l 4min. d 2d 3 6H d 50 1 25 54 24 25 59 65 M18 2 45 32 58 24 28 63 72 0 1 M20

24、 2 56 40 68 30 32 73 80 M20 2 60 50 78 35 35 83 90 M24 2 70 63 88 40 40 93 130 max. M24 2 a aAt the discretion of the manufacturer. BSISO54141:20023IS-4145 O1:(2002)E 4 I SO 2002 All irthgs ersedevr3.3 Clamp screw See Figure 3 and Table 3. Figure 3 Table 3 Dimensions in millimetres d 36h d 4+ 0,10l

25、aBoring chucks, d 1M6 4,2 10 6 M8 5,5 10 8 M10 7 12 10 M12 8 16 12 M14 10 16 16 M16 11 16 20 M18 2 12 20 25 M20 2 14 20 32 M20 2 14 25 40 M24 2 18 25 50 M24 2 18 33 63 aThe values given represent the screw nominal length for boring chucks d 1u 32 mm. For larger chucks, l values are given for guidanc

26、e and calculated from maximum values of d 5 . In the case of reduced d 5 bore, the screw length should be re-calculated making sure that the engagement length is appropriate. BSISO54141:20024IS-4145 O1:(2002)E I SO 2002 All irthgs ersedevr 5Bibliography 1 ISO 5414-2, Tool chucks (end mill holders) w

27、ith clamp screws for flatted cylindrical shank tools Part 2: Connecting dimensions of chucks and designation BSISO54141:20025BS ISO 5414-1:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards.

28、 It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant a

29、im of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44

30、 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed t

31、o Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as B

32、ritish Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give

33、 details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details

34、 of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available o

35、n the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, sto

36、red in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.