BS ISO 4141-2-2006 Road vehicles - Multi-core connecting cables - Test methods and requirements for high performance sheathed cables《道路车辆 多芯连接电缆 高性能铠装电缆试验方法和要求》.pdf

《BS ISO 4141-2-2006 Road vehicles - Multi-core connecting cables - Test methods and requirements for high performance sheathed cables《道路车辆 多芯连接电缆 高性能铠装电缆试验方法和要求》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 4141-2-2006 Road vehicles - Multi-core connecting cables - Test methods and requirements for high performance sheathed cables《道路车辆 多芯连接电缆 高性能铠装电缆试验方法和要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Part 2: Test methods and requirements for high performance sheathed cablesICS 43.040.10Road vehicle

2、s Multi-core connecting cables BRITISH STANDARDBS ISO 4141-2:2006BS ISO 4141-2:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2006 BSI 2006ISBN 0 580 48649 4Cross-referencesThe British Standards which implement international publ

3、ications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the nec

4、essary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank

5、 page, pages 1 to 5 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this committee can be obtained on request to its secretary. present to

6、the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard reproduces verbatim ISO 4141-2:2

7、006 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee AUE/16, Electrical and electronic equipment, which has the responsibility to: aid enquirers to understand the text;INTERNATIONALSTANDARDISO4141-2Second edition2006-07-01Ref

8、erence numberISO 4141-2:2006(E)Road vehicles Multi-core connecting cables Part 2:Test methods and requirements for high performance sheathed cablesVhicules routiers Cbles de raccordement multiconducteurs Partie 2: Mthodes dessai et exigences pour les cbles gains hautes performancesBS ISO 4141-2:2006

9、iiiiiForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a

10、 technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the InternationalElectrotechnical Commission (IEC) on all matters

11、of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to

12、 the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for ide

13、ntifying any or all such patent rights.ISO 4141-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electricaland electronic equipment.This second edition cancels and replaces the first edition (ISO 4141-2:1998), which has been technicallyrevised.ISO 4141 consists of t

14、he following parts, under the general title Road vehicles Multi-core connecting cables: Part 1: Test methods and requirements for basic performance sheathed cables Part 2: Test methods and requirements for high performance sheathed cables Part 3: Construction, dimensions and marking of unscreened sh

15、eathed low-voltage cables Part 4: Articulation test method and requirements for coiled cable assembliesThe following part is under preparation: Part 4: Test methods and requirements for coiled cable assemblies Revision of ISO 4141-4:2001BS ISO 4141-2:2006blank1Road vehicles Multi-core connecting cab

16、les Part 2:Test methods and requirements for high performance sheathed cables1ScopeThis part of ISO 4141 specifies the test methods and requirements for high performance sheathed multi-corecables for the connection of towing and towed vehicles, suitable for a temperature range of to .2 Normative ref

17、erencesThe following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenced document(including any amendments) applies.ISO 1817, Rubber, vulcanized Determination of

18、 the effect of liquidsISO 4141-1, Road vehicles Multi-core connecting cables Part 1: Test methods and requirements for basicperformance sheathed cablesISO 4141-3, Road vehicles Multi-core connecting cables Part 3: Construction, dimensions and marking ofunscreened sheathed low-voltage cablesISO 6722,

19、 Road vehicles 60 V and 600 V single-core cables Dimensions, test methods and requirementsISO 14572, Road vehicles Round, screened and unscreened 60 V and 600 V multi-core sheathed cables Test methods and requirements for basic and high performance cables3 General requirementsHigh performance sheath

20、ed multi-core cables shall be in accordance with ISO 4141-1 and shall meet theadditional test and requirements or modified test conditions specified in Clause 4.Coiled multi-core cables shall in addition meet the tests and requirements specified in Clause 5.4 Tests and requirements4.1 ImpactSee ISO

21、4141-1 but use a freezing temperature of .4.2 Pressure at high temperatureSee ISO 14572 and apply the requirements for high performance cables.40C +85C(20 2)CBS ISO 4141-2:200624.3 Cyclic bendingSee ISO 4141-1 but use 10 000 cycles.4.4 Fluid compatibility of the sheath4.4.1 GeneralFor each test, use

22、 three samples each of minimum length at least apart on the cable.Bend each test sample to a radius of five times the outside diameter and secure it.4.4.2 Tests4.4.2.1 Resistance against ethanolSee ISO 6722 but use a time frame of .4.4.2.2 Resistance against sulphuric acidImmerse the bent test sampl

23、es for in dilute battery acid of density at a temperature of. Remove the test samples from the test liquid, rinse and wipe them thoroughly, straighten them, and thenexamine them visually.4.4.2.3 Resistance against lubrication oilImmerse the bent test samples for in lubrication oil No. 1 as specified

24、 in ISO 1817 at a temperature of.Remove the test samples from the test liquid, wipe them thoroughly, straighten them, and then examine themvisually.4.4.2.4 Resistance against zinc chlorideImmerse the bent test samples in an aqueous solution of zinc chloride, mass fraction, for at atemperature of .Re

25、move the test samples from the test liquid, wipe them thoroughly, straighten them and then examine themvisually.4.4.3 RequirementThe sheath shall show no evidence of fracture or cracking.300 mm 1m180min.168 h48 h 1 275 g/cm3(23 5)C168 h(23 5)C50 % 168 h(23 5)CBS ISO 4141-2:200635 Specific tests and

26、requirements for coiled multi-core cables5.1 Elongation by cable weight5.1.1 TestMeasure the initial block length of the complete coil at rest and in horizontal position.Then hang the cable vertically. After at least , measure the extended coil length.5.1.2 RequirementThe extended coil length shall

27、not be more than twice the initial block length.5.2 Resistance against cyclic extension5.2.1 TestThis test may be performed with the sample used in 5.1. Position the sample horizontally in a test apparatus andsubject it to the two test sequences specified in Table 1.The test shall be carried out at

28、a frequency of .Conductor breakage shall be monitored by applying a current to all conductors during the entiretest phase. If breakage occurs, the test procedure shall stop automatically.5.2.2 RequirementNo conductor shall break during the test. At the end, under visual examination, the sheath shall

29、 show noevidence of fracture or cracking.5.3 Restoring force5.3.1 TestPrecondition the cable: by one extension to its max. admitted extension length; 5 minutes rest, unstretched, at room temperature; rest for in a freezing chamber at .Table 1 Cyclic extension test, number of cyclesTest sequence Exte

30、nsion Number of cyclesa1 To max. value of working length ( )b200 0002 To max. admitted extension length ( )b20 000aOne cycle consists of: extension of the sample to its working length (test sequence 1) or to its maximum admitted extension length (test sequence 2); contraction to its original block l

31、ength including the uncoiled cable lengths.bAccording to ISO 4141-3.60 sLALAmax(10 5) cycles/min(5 0,5) A4h (40 2)CBS ISO 4141-2:20064Then within of removing the sample from the freezing chamber, measure the restoring force of the cablewhen extended to its max. admitted extension length.5.3.2 Requir

32、ementThe restoring force shall not exceed .5.4 Cable sag5.4.1 TestMount one cable as shown in Figure 1 and measure its sag successively after each of the following conditions:a) one extension to its max. admitted extension length, and subsequently rest unstretched;b) conditioning in a heating chambe

33、r at , one extension to its max. admitted extension lengthwithin after removing from the heating chamber, and subsequently rest at room temperature,unstretched;c) the cyclic extension test in 5.2, and subsequently 5 minutes rest, unstretched.Dimensions in millimetresaSee ISO 4141-3.Figure 1 Measurem

34、ent of cable sag60 s180 N60 s2h (80 2)C15 s 60 sBS ISO 4141-2:200655.4.2 RequirementThe measured cable sag shall not exceed the values specified in Table 2.5.5 Permanent elongation5.5.1 TestMeasure the block length of the cable as delivered and after each of the following conditioning procedures:a)

35、one extension to its max. admitted extension length and subsequently rest in restored condition atroom temperature;b) conditioning at a temperature of , one extension to its max. admitted extension lengthwithin after removing from the temperature chamber, and subsequently rest in restored conditiona

36、t room temperature;c) as b), but conditioning at ;d) as b), but conditioning at .Measurement shall be taken with a sample positioned horizontally on a plane surface of low friction. Thereleased sample may be lifted and allowed to fall, to reduce the effect of friction.5.5.2 RequirementThe measured c

37、hange of block lengths shall not exceed the values specified in Table 3.Table 2 Maximum cable sagMeasurement taken with cable at rest after conditioning according toCable sag, mmmax.5.4.1 a) 4005.4.1 b) 4505.4.1 c) 650Table 3 Extension of block lengthMeasurements taken after conditioning as inChange

38、 of block length%amax.5.5.1 a) 105.5.1 b) 155.5.1 c) 205.5.1 d) 50aPercentage of the block length of the coiled cable as delivered.L230 s2h (40 2)C15 s 120 s2h (60 2)C2h (80 2)CBS ISO 4141-2:2006BS ISO BSI389 Chiswick High RoadLondonW4 4AL4141-2:2006BSI British Standards InstitutionBSI is the indepe

39、ndent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they p

40、ossess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the ident

41、ity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, internationa

42、l and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the

43、BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electr

44、onic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial dis

45、counts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/

46、www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents

47、 Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary det

48、ails such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.