BS ISO 4129-2012 Road vehicles Mopeds Symbols for controls indicators and tell-tales《道路车辆 助力车 操纵装置 指示仪和信号装置的符号》.pdf

《BS ISO 4129-2012 Road vehicles Mopeds Symbols for controls indicators and tell-tales《道路车辆 助力车 操纵装置 指示仪和信号装置的符号》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 4129-2012 Road vehicles Mopeds Symbols for controls indicators and tell-tales《道路车辆 助力车 操纵装置 指示仪和信号装置的符号》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 4129:2012Road vehicles Mopeds Symbols for controls, indicators and tell-talesBS ISO 4129:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementati

2、on of ISO 4129:2012. The UK participation in its preparation was entrusted to T e c h n i c a l Committee AUE/14, Motor cycles and mopeds.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary p

3、rovisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 59332 1 ICS 01.080.20; 43.140 Compliance with a British Standard cannot confer immunity from legal obligations.This British Stand

4、ard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 4129:2012Reference numberISO 4129:2012(E)ISO 2012INTERNATIONAL STANDARD ISO4129Third edition2012-09-15Road vehicles Mopeds S

5、ymbols for controls, indicators and tell-tales Vhicules routiers Cyclomoteurs Symboles pour les commandes, les indicateurs et les tmoins BS ISO 4129:2012ISO 4129:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduc

6、ed or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749

7、01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2012 All rights reservedBS ISO 4129:2012ISO 4129:2012(E) ISO 2012 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 General . 1 Annex A (normative) Lighting and signalling devices 3 Annex B

8、 (normative) Braking system . 5 Annex C (normative) Engine 6 Annex D (normative) Fuel system . 7 Annex E (normative) Transmission 8 Annex F (normative) Electrical functions in general, and electric or hybrid electric mopeds . 9 Annex G (normative) Security . 10 Bibliography 11 BS ISO 4129:2012ISO 41

9、29:2012(E) iv ISO 2012 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member

10、body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electr

11、otechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.

12、Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of ISO 4129 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent r

13、ights. ISO 4129 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 23, Mopeds. This third edition cancels and replaces the second edition (ISO 4129:1990), which has been technically revised. BS ISO 4129:2012INTERNATIONAL STANDARD ISO 4129:2012(E) ISO 2012 All rights reserv

14、ed 1Road vehicles Mopeds Symbols for controls, indicators and tell-tales 1 Scope This International Standard specifies the symbols, i.e. conventional signs, used to identify certain controls, indicators and tell-tales on a moped1)and to facilitate their usage 2). This International Standard also ind

15、icates the colours of possible optical tell-tales which warn the driver of the operation or malfunctioning of the related devices and equipment. This International Standard is applicable to those controls, indicators and tell-tales, which, when used, are fitted on the instrument panel or in the imme

16、diate vicinity of the moped rider. 2 General 2.1 It is not mandatory to adopt a symbol for all controls, indicators and tell-tales likely to be fitted on the moped. Nevertheless, when symbols are provided (because they have been enforced by law or for any manufacturers reason) their type shall be as

17、 specified in this International Standard. 2.2 The symbols must be such that, when viewed by the driver, from his normal seated position, they are recognizable as shown in Annexes A to G 3). 2.3 Symbols on controls and tell-tales shall have a good contrast with their background. Some symbols can be

18、only embossed if the symbols are identified clearly without paint. 2.4 The symbol must be placed on, or adjacent to, the control or tell-tale to be identified. Where this is not possible, the symbol and the control or tell-tale must be joined by a continuous line as short as possible. 2.5 If, in a s

19、ymbol, a moped or parts of a moped are shown in a side view, a moped driving from right to left shall be used. 2.6 Focused light shall be represented by parallel rays and diffuse light by divergent rays. 2.7 When the following colours are used on the optical tell-tales, they shall have the meaning i

20、ndicated below: red: danger; yellow (amber): caution; 1) Moped as defined in ISO 3833. 2) Prints of these symbols for reproduction purposes may be obtained from the ISO Central Secretariat. 3) Many of these symbols are also contained in ISO 2575. The symbol reference number may be different in the t

21、wo international standards but the ISO/IEC registration number is the same. BS ISO 4129:2012ISO 4129:2012(E) 2 ISO 2012 All rights reserved green: safety; blue shall only be used for the headlight upper beam tell-tale. BS ISO 4129:2012ISO 4129:2012(E) ISO 2012 All rights reserved 3Annex A (normative

22、) Lighting and signalling devices Symbol number Symbol form/shape Symbol description/application ISO/IEC registration number A.01 High (main) beamColour of telltale light: blue Framed areas of this symbol may be solid. The control operating alternately the high beam and the low beam may include two

23、symbols, one for each of the positions: high beam, low beam. 7000-0082 A.02 Low (dipped) beamFramed areas of this symbol may be solid. The control operating alternately the high beam and the low beam may include two symbols, one for each of the positions: high beam, low beam. 7000-0083 A.03 Front fo

24、g lightColour of telltale light: green If one control is used for both front and rear fog lights, this symbol shall be used. 7000-0633 A.04 Rear fog lightColour of telltale light: yellow (amber) If one control is used for both front and rear fog lights, the symbol for front fog light (A.03) shall be

25、 used. 7000-0634 A.06 Position lightsLighting switch may be combined with ignition control. 7000-0456 A.07 Master lighting switch Lighting switch may be combined with ignition control. Application of IEC 60417-5012 A.08 Turn signalsColour of telltale light: green Framed areas of this symbol may be s

26、olid. 7000-0084 BS ISO 4129:2012ISO 4129:2012(E) 4 ISO 2012 All rights reservedSymbol number Symbol form/shape Symbol description/application ISO/IEC registration number A.09 Hazard warningSimultaneous operation of both green turn signal tell-tales, or separate red signal. This symbol applies only t

27、o the control and to the separate red tell-tale. Framed areas of this symbol may be solid. 7000-0085 A.10 Horn 7000-0244 BS ISO 4129:2012ISO 4129:2012(E) ISO 2012 All rights reserved 5Annex B (normative) Braking system Symbol number Symbol form/shape Symbol description/application ISO/IEC registrati

28、on number B.01 Anti-lock brake system, failureColour of telltale light: yellow (amber) The letters “ABS“ may match the type style used throughout the instrument panel. 7000-1407 BS ISO 4129:2012ISO 4129:2012(E) 6 ISO 2012 All rights reservedAnnex C (normative) Engine Symbol number Symbol form/shape

29、Symbol description/application ISO/IEC registration number C.01 Engine coolant temperatureColour of telltale light: red 7000-0246 C.02 Engine oil Colour of telltale light: red Framed areas of this symbol may be solid. 7000-0248 C.03 Choke Manual choke (cold starting aid) Colour of telltale light: ye

30、llow (amber) 7000-0243 C.04 Ignition control of supplemental engine stop (Run) 7000-2425 C.05 Ignition control of supplemental engine stop (Off) 7000-1180 C.06 Engine Colour of telltale light: yellow (amber) 7000-0640 BS ISO 4129:2012ISO 4129:2012(E) ISO 2012 All rights reserved 7Annex D (normative)

31、 Fuel system Symbol number Symbol form/shape Symbol description/application ISO/IEC registration number D.01 or Fuel Colour of telltale light: yellow (amber) This symbol may also be used on the filler cap of the fuel tank. 7000-0245 D.02 Fuel tank shut off valve position, “off“ Framed areas of this

32、symbol may be solid. 4)D.03 Fuel tank shut off valve position, “on“ Framed areas of this symbol may be solid. 7000-3031 D.04 Fuel tank shut off valve position, “reserve“ Framed areas of this symbol may be solid. 7000-3032 4) Not registered in ISO 7000, but required for mopeds by UNECE global technic

33、al regulation (UNECE/TRANS/180/Add.12). BS ISO 4129:2012ISO 4129:2012(E) 8 ISO 2012 All rights reservedAnnex E (normative) Transmission Symbol number Symbol form/shape Symbol description/application ISO/IEC registration number E.01 Neutral IndicatorColour of telltale light: green May match the type

34、style used throughout the instrument panel. BS ISO 4129:2012ISO 4129:2012(E) ISO 2012 All rights reserved 9Annex F (normative) Electrical functions in general, and electric or hybrid electric mopeds Symbol number Symbol form/shape Symbol description/application ISO/IEC registration number F.01 Batte

35、ry charging conditionColour of telltale light: red 7000-0247 F. 02 Electric starter; engine electric start 7000-3033A F.03 Ignition switch Application of IEC 60417-5009 F.04 On Position (Ignition Switch) Application of IEC 60417-5007 F.05 Off Position (Ignition Switch) Application of IEC 60417-5008

36、BS ISO 4129:2012ISO 4129:2012(E) 10 ISO 2012 All rights reservedAnnex G (normative) Security Symbol number Symbol form/shape Symbol description/application ISO/IEC registration number G.01 Steering Lock Application of IEC 60417-5569 G.02 Helmet lock (Helmet holder) 7000-3034 BS ISO 4129:2012ISO 4129

37、:2012(E) ISO 2012 All rights reserved 11Bibliography 1 ISO 2575, Road vehicles Symbols for controls, indicators and tell-tales 2 ISO 3833, Road vehicles Types Terms and definitions 3 ISO 7000, Graphical symbols for use on equipment Registered symbols 4 UNECE/TRANS/180/Add.12, 2011, Global technical

38、regulation concerning the location, identification and operation of motorcycle controls, tell-tales and indicators, Addendum 12 5 IEC 60417, Graphical symbols for use on equipment BS ISO 4129:2012ISO 4129:2012(E) ICS 01.080.20; 43.140 Price based on 11 pages ISO 2012 All rights reserved This page de

39、liberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Stand

40、ards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. User

41、s of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Sec

42、retary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensu

43、res that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders f

44、or BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unl

45、ess otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and r

46、eceive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be f

47、ound at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (s

48、uch as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these det