BS ISO 4000-2-2013 Passenger car tyres and rims Rims《乘用车轮胎和轮辋 轮辋》.pdf

《BS ISO 4000-2-2013 Passenger car tyres and rims Rims《乘用车轮胎和轮辋 轮辋》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 4000-2-2013 Passenger car tyres and rims Rims《乘用车轮胎和轮辋 轮辋》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 4000-2:2013Passenger car tyres and rimsPart 2: RimsBS ISO 4000-2:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 4000-2:2013. Itsupersedes BS ISO 4000-2:2007 which is withdrawn.The UK participation in its preparation was ent

2、rusted to TechnicalCommittee AUE/4, Tyres and wheels for motor vehicles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplic

3、ation. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 79660 9ICS 43.040.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committe

4、e on 31 December 2013.Amendments issued since publicationDate Text affectedBS ISO 4000-2:2013 ISO 2013Passenger car tyres and rims Part 2: RimsPneumatiques et jantes pour voitures particulires Partie 2: JantesINTERNATIONAL STANDARDISO4000-2Fifth edition2013-12-15Reference numberISO 4000-2:2013(E)BS

5、ISO 4000-2:2013ISO 4000-2:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or

6、posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyri

7、ghtiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 4000-2:2013ISO 4000-2:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Designation and marking 15 5 tapered (drop-centre) rims 15.1 Rim flanges . 15.2 Rim contours.

8、25.3 Rim diameter and hump circumference . 56 Valve holes . 66.1 General . 66.2 Snap-in . 66.3 Other valves . 6BS ISO 4000-2:2013ISO 4000-2:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of

9、preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental,

10、 in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/

11、IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility

12、 that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of paten

13、t declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as informa

14、tion about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 31, Tyres, rims and valves, Subcommittee SC 3, Passenger car tyres and rims.This fifth edition can

15、cels and replaces the fourth edition (ISO 4000-2:2007), which has been technically revised.ISO 4000 consists of the following parts, under the general title Passenger car tyres and rims: Part 1: Tyres (metric series) Part 2: Rimsiv ISO 2013 All rights reservedBS ISO 4000-2:2013INTERNATIONAL STANDARD

16、 ISO 4000-2:2013(E)Passenger car tyres and rims Part 2: Rims1 ScopeThis part of ISO 4000 specifies the designation, contour and dimensions of 5 tapered (drop-centre) rims primarily intended for passenger cars.2 Normative referencesThe following documents, in whole or in part, are normatively referen

17、ced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3911, Wheels and rims for pneumatic tyres Vocabulary, designation and mar

18、king3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 3911 apply.4 Designation and markingThe rim shall be designated by its nominal rim-diameter code, nominal rim-width code and rim flange type (e.g. 15 6 J or 13 5,50 B).5 5 tapered (drop-centre) rims5

19、.1 Rim flangesRecommended rim flange contours are given in Table 1 for the nominal rim diameter codes. ISO 2013 All rights reserved 1BS ISO 4000-2:2013ISO 4000-2:2013(E)Table 1 Recommended rim flangesNominal rim-diameter code Rim flange10B121314J15161718192021222324252628305.2 Rim contoursDimensions

20、 and tolerances of the rims shall be as given in Figure 1 and Table 2. Optional bead seat contours and their dimensions are given in Figure 2 and Table 3.2 ISO 2013 All rights reservedBS ISO 4000-2:2013ISO 4000-2:2013(E)Dimensions in millimetresKey1 valve hole (see Clause 6)2 tyre mounting side3 bre

21、ak corner equivalent to 0,5 minimum R4 tyre non-mounting sideaFlange width includes edge radius. The portion of a flange beyond the minimum width shall not be higher than the highest point of the flangebThese dimensions comprise the minimum well envelope for tyre mounting purposes at M max. or less,

22、 except for localized areas at the weld or valve holeCOptional groove in rim flange for wheel weight retention is permissibleNOTE For use with tubeless tyres, humps are necessary on the mounting side and preferred on the non-mounting side.Figure 1 Contour of 5 tapered (drop-centre) rims ISO 2013 All

23、 rights reserved 3BS ISO 4000-2:2013ISO 4000-2:2013(E)Table 2 Dimensions of 5 tapered (drop-centre) rimsDimensions in millimetresDiameter codeRim width code and flange type cB G P P1H aL M R2min. 1,0 min. min. gauge gauge max. min.1012133.00 B 10,0 14,5 13,0 15,0 15,0 16,0 28,0 7,53.50 B 10,0 14,5 1

24、5,0 17,0 15,0 19,0 34,0 7,54.00 B 10,0 14,5 15,0 17,0 15,0 19,0 45,0 7,54.50 B and wider10,0 14,5 19,5 19,5 15,0 22,0 45,0 7,514 through 213J 11,0 17,5 13,0 13,0 17,3 b16,0 28,0 9,531/2 J 11,0 17,5 15,0 17,0 17,3 b19,0 34,0 9,54 J 11,0 17,5 15,0 17,0 17,3 b19,0 45,0 9,541/2 J and wider11,0 17,5 19,5

25、 19,5 17,3 b22,045,0 9,522 and greater4 1/2 J and wider11,0 17,5 19,5 19,5 22,0 d22,045,0 9,5aMinimum dimensions for well depth (H) and well angle are required for tyre mounting. Larger values may be required to ensure sufficient space for tubeless tyre valve seating.bFor J-type rims, a deviation to

26、 H gauge of 17 mm is permitted with a corresponding M max. of 43 mm.cDimension A = rim width code 25,4 (rounded to 0,5 mm) (increments of code = 0.5).dSome existing designs may follow minimum value of 17,3 well depth.4 ISO 2013 All rights reservedBS ISO 4000-2:2013ISO 4000-2:2013(E)Dimensions in mil

27、limetresKey1 tyre mounting side2 tyre non-mounting sideFigure 2 Optional bead seat contoursTable 3 E dimension for round humps (see Figure 2)Dimensions in millimetresRim width code and flange type E3.00 B and 3 J 13 min.3.50 B, 31/2 J, 4.00 B, 4 J 16 min.4.50 B, 41/2 J and wider 21 0020,+aa19 5020,+

28、mm permitted for rim widths 4.50 B (41/2 J) to 7.00 B (7 J).5.3 Rim diameter and hump circumferenceThe specified rim diameter, D, for nominal rim-diameter codes and hump circumferences is given in Table 4. ISO 2013 All rights reserved 5BS ISO 4000-2:2013ISO 4000-2:2013(E)Table 4 Specified rim diamet

29、er and hump circumference of 5 tapered (drop-centre) rimsDimensions in millimetresNominal rim-diameter codeSpecified rim diameter CircumferenceD 0,4aFlat hump 350,Round hump 350,b10 253,2 795,4 797,612 304,0 955,0 957,613 329,4 1 034,8 1 037,014 354,8 1 114,6 1 116,815 380,2 1 194,4 1 196,616 405,6

30、1 274,2 1 276,417 436,6 1 371,6 1 373,818 462,0 1 451,4 1 453,619 487,4 1 531,2 1 533,420 512,8 1 611,0 1 613,221 538,2 1 690,8 1 693,022 563,6 1 770,6 1 772,823 589,0 1 850,4 1 852,624 614,4 1 930,2 1 932,425 639,8 2 010,0 2 012,226 665,2 2 089,8 2 092,028 716,0 2 249,4 2 251,630 766,8 2 409,0 2 41

31、1,2aTolerance is for tyre design purpose only. The rim measurement is by a circumference-measuring tape related to a mandrel.bA tolerance of 500,mm is permitted on the vehicle inboard side only.6 Valve holes6.1 GeneralValve hole edges on the tyre side of rims shall be rounded or chamfered; valve hol

32、e edges on the weather side of rims shall be free from burrs that could damage the valve.6.2 Snap-inTo provide for adequate sealing, an unbroken smooth inside surface having at least 0,75 mm or 25 % of rim thickness, whichever is greater, shall be maintained. Suitable valves shall be used. Valve hol

33、e details for snap-in valves shall be as shown in Figure 3 or 4 for rims with 17,3 mm minimum well depth.6.3 Other valvesHoles for other valves are under consideration.6 ISO 2013 All rights reservedBS ISO 4000-2:2013ISO 4000-2:2013(E)Dimensions in millimetresFigure 3 Valve hole dimensions for snap-i

34、n valvesDimensions in millimetresKey1 flat surface with no radial striations2 flat surface for clamp-in valvesFigure 4 Valve hole dimensions around valve hole ISO 2013 All rights reserved 7BS ISO 4000-2:2013ISO 4000-2:2013(E) ISO 2013 All rights reservedICS 43.040.50Price based on 7 pagesThis page d

35、eliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Stan

36、dards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has

37、been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed

38、. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at wher

39、e hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For fur

40、ther information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch wit

41、h standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of y

42、our standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wi

43、sh. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit

44、 your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or so

45、me person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,

46、 stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW