BS ISO 29404-2015 Ships and marine technology Offshore wind energy Supply chain information flow《船舶与海洋技术 海上风能 供应链信息流》.pdf

《BS ISO 29404-2015 Ships and marine technology Offshore wind energy Supply chain information flow《船舶与海洋技术 海上风能 供应链信息流》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 29404-2015 Ships and marine technology Offshore wind energy Supply chain information flow《船舶与海洋技术 海上风能 供应链信息流》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 29404:2015Ships and marine technology Offshore wind energy Supply chain information flowBS ISO 29404:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 29404:2015.The UK participation in its preparation was entrusted to Technic

2、alCommittee SME/32, Ships and marine technology - Steeringcommittee.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplicatio

3、n. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 87303 4ICS 47.020.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on

4、 31 December 2015.Amendments issued since publicationDate Text affectedBS ISO 29404:2015 ISO 2015Ships and marine technology Offshore wind energy Supply chain information flowNavires et technologie maritime nergie olienne offshore Flux dinformations dans la chane dapprovisionnementINTERNATIONAL STAN

5、DARDISO29404First edition2015-12-01Reference numberISO 29404:2015(E)BS ISO 29404:2015ISO 29404:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utiliz

6、ed otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright

7、officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 29404:2015ISO 29404:2015(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 14 Abbreviated terms 55 Supply chain process

8、es: Planning, ordering and monitoring 55.1 General . 55.2 Production of parts and components 75.3 Inland and nearshore transport . 85.3.1 Transport by ground. 85.3.2 Transport by ship 85.3.3 Transport by rail 85.3.4 Transport by aircraft 95.4 Storage . 95.5 Installation . 105.6 Maintenance and repai

9、r . 115.7 Return of load carriers and equipment 115.8 Decommissioning 126 Exchange of logistics information via EPCIS .127 Identification of relevant parties, objects and elements .147.1 General 147.2 Roles and parties 147.2.1 General. 147.2.2 Manufacturer .147.2.3 Supplier . 147.2.4 Transport opera

10、tor .157.2.5 Logistic service provider 157.2.6 Port operator 157.2.7 Installation operator 157.2.8 Project owner 157.2.9 Others . 157.3 Identifying parties and business locations 157.3.1 General. 157.3.2 Unique identifier for involved parties 157.3.3 Unique identifier for locations 167.4 Parts and c

11、omponents . 167.4.1 General. 167.4.2 Components 167.4.3 Bundles of components . 177.4.4 Load carriers and lifting equipment 177.5 Transport media and machinery 177.5.1 General. 177.5.2 Trucks . 177.5.3 Trains and wagons 177.5.4 Vessels 187.5.5 Aircraft . 187.5.6 Other 187.6 Container . 187.7 Unique

12、identification numbers 187.7.1 General. 187.7.2 Representation of unique identifiers 18 ISO 2015 All rights reserved iiiContents PageBS ISO 29404:2015ISO 29404:2015(E)7.7.3 Usage of existing unique numbering systems .198 Master data 199 Event data .209.1 General 209.2 General extensions of event fie

13、lds . 219.3 Plan data 219.4 Order data 239.5 Material flow event messages . 249.6 Extensibility and specific implementation design 269.6.1 General. 269.6.2 Vocabulary extensions .279.6.3 Event field extensions .2710 Data formats .2811 Data carriers 2811.1 General 2811.2 Barcodes 2811.3 RFID . 2911.4

14、 Others . 29Annex A (normative) XML scheme for field extensions .30Annex B (informative) Example messages in the offshore supply chain .31Bibliography .36iv ISO 2015 All rights reservedBS ISO 29404:2015ISO 29404:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide f

15、ederation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that co

16、mmittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document

17、and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, P

18、art 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of

19、the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific te

20、rms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 8, Ships and marine techno

21、logy.This International Standard is part of a series for offshore structures of the offshore wind industry. The full series consists of the following: ISO 29400, Ships and marine technology Offshore wind energy Port and marine operations ISO 29404, Ships and marine technology Offshore wind energy Su

22、pply chain information flow ISO 2015 All rights reserved vBS ISO 29404:2015ISO 29404:2015(E)IntroductionThe complexity and the number of parties involved in the offshore wind farm (OWF) supply chains, both during the construction and the operational phase with their repair and maintenance requiremen

23、ts, depend on IT applications to facilitate planning and control of all physical processes.In order to minimize frictions in data communication between different business parties, content and format of data need to be standardized.vi ISO 2015 All rights reservedBS ISO 29404:2015Ships and marine tech

24、nology Offshore wind energy Supply chain information flow1 ScopeThis International Standard specifies content and format of the messages initiating and controlling the physical movement of wind turbine generator (WTG) components from suppliers to the construction site during the construction phase a

25、s well as for repair and maintenance purposes.This International Standard is applicable to all organizations involved in the production, transportation, storage and installation of WTG parts and related components. This International Standard is not intended to be applied to substations.Messages des

26、cribed in this International Standard covers only the operational aspects of logistics and therefore this International Standard will represent only one aspect of the entire information flow.This International Standard does not specify the technical implementation of appropriate IT products. It rath

27、er provides an approach based on the EPC Information System (EPCIS) standard and describes the usage of extension mechanisms provided by the EPCIS standard for the exchange of information in the offshore wind supply chain. It aims at standardizing the exchange of essential logistic information. This

28、 International Standard specifies elementary informational needs of involved parties in the offshore supply chain and defines mechanisms for the exchange of this information via the EPCIS. Due to the high degree of specialization along different offshore supply chains, partners exchanging informatio

29、n might require mechanisms for personalizing according to their individual demands. The underlying extendable EPCIS concept allows end users and industry consortiums to extend and to refine the information exchange. These extensions might go far beyond the basic information exchange described in thi

30、s International Standard.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docum

31、ent (including any amendments) applies.ISO 29400, Ships and marine technology Offshore wind energy Port and marine operationsEPC Information Services (EPCIS) Version 1.1 SpecificationCore Business Vocabulary (CBV) GS1 Standard Version 1.13 Terms and definitionsFor the purposes of this document, the

32、terms and definitions given in ISO 29400 and the following apply.3.1automatic identification data capturingAIDCmethods of automatically identifying objects, collecting data about them, and entering that data directly into computer systemsINTERNATIONAL STANDARD ISO 29404:2015(E) ISO 2015 All rights r

33、eserved 1BS ISO 29404:2015ISO 29404:2015(E)3.2bar codelinear array of rectangular marks of (possibly) varying width, height and vertical alignment, separated by spaces of (possibly) varying width, in which the positioning and size of marks and spaces are used to encode informationNote 1 to entry: Ba

34、r code may be 1D bar code or 2D bar code, also called Aztec code.3.3componentarbitrarily parts of a WTG, comprising foundations and all parts of a wind turbine generator as well as elements of a wind turbine generator towerEXAMPLE Tripods, jackets, monopoles and other foundation types and blades and

35、 hubs.3.4container owner codeBIC codecoding scheme used for coding, identification and marking of containers used within containerized intermodal freight transportNote 1 to entry: For detailed information, see Reference 1.3.5coordinateone of a sequence of n numbers designating the position of a poin

36、t in n-dimensional spaceNote 1 to entry: In a coordinate reference system, the coordinate numbers are qualified by units.SOURCE: ISO 19111:2007, 4.53.6coordinate tupletuple composed of a sequence of coordinatesNote 1 to entry: The number of coordinate tuple equals the dimension of the coordinate sys

37、tem; the order of coordinates in the coordinate tuple is identical to the order of axes of the coordinate system.SOURCE: ISO 19111:2007, 4.12 modified3.7IMO numberunique identifiers for ships governed by IMONote 1 to entry: For more information, see IMO Resolution A.600(15).Note 2 to entry: The issu

38、ing agency for IMO numbers is IHS Fairplay.3.8installation siteoffshore location where WTGs are installed in an offshore wind farm3.9inland transporttransport of components which does not operate in offshore or coastal areasEXAMPLE Via roads, via rail, via inland vessel and via plane.3.10issuing age

39、ncyagency that defines and governs unique numbering schemesNote 1 to entry: For more information, see ISO/IEC 15459-2.2 ISO 2015 All rights reservedBS ISO 29404:2015ISO 29404:2015(E)3.11locationuniquely identifiable physical point or areaNote 1 to entry: The location can be characterized by coordina

40、tes.3.12logistics hublocation where flows of components are consolidated, stored or transhippedNote 1 to entry: Logistic hubs are usually located in the inland or the coastal area.Note 2 to entry: Supply chains may comprise multiple logistics hubs.3.13logistic service providerrole in the offshore su

41、pply chain which is responsible for the organization of parts or of the entire logistics chain3.14manufacturerorganization that produces one or more components for offshore wind turbines3.15n-tierorganization that supplies one or more manufacturer with raw material and semi-finished products3.16near

42、shore transportwater-based transport operated next to the coast or in mouths of rivers3.17offshore transporttransportation of components from designated marshalling port or another fabrication yard to the offshore installation site in the offshore wind farm3.18sea fasteningtemporary fastening items

43、which keep movable items in position during sea and waterways transport3.19sending partylegal entity that sends components to a receiving party3.20storage framesstructure to support storing of the WTG components3.21suppliercompany which produces semi-finished products for the assembly of components

44、of a WTG3.22radio-frequency identificationRFIDwireless non-contact use of radio-frequency electromagnetic fields to transfer data3.23telemetryautomated collection of operational data and its transfer via an information and communication infrastructure ISO 2015 All rights reserved 3BS ISO 29404:2015I

45、SO 29404:2015(E)3.24trailersystem of steerable wheels, connected to a central spine beam by hydraulic suspension that can be raised or lowered3.25transport mediaall kinds of vehicle that may be used to transport components, bundles of component, load carriers, lifting equipment and other related obj

46、ects3.26unique identifieridentifier which is guaranteed to be unique among all identifiers used for those objects and for a specific purposeNote 1 to entry: For more information, see ISO/IEC 15459-1.3.27process statestate of a process that describes the disposition and the current business step of a

47、 process3.28extensible markup languageXMLschema that defines a set of rules for encoding documents in a format that is both human-readable and machine-readable3.29xml schemeabstract collection of metadata, consisting of a set of schema components with element and attribute declarations and complex a

48、nd simple type definitionsNote 1 to entry: For more information, see References 18 and 21.4 ISO 2015 All rights reservedBS ISO 29404:2015ISO 29404:2015(E)4 Abbreviated termsAIS Automatic Identification SystemCBV Core Business VocabularyEPC Electronic Product CodeEPCIS EPC Information ServicesIMO Int

49、ernational Maritime OrganizationGIAI Global Individual Asset IdentifierGLN Global Location NumberGTIN Global Trade Item NumberGPS Global Positioning SystemGRAI Global Returnable Asset IdentifierOWF Offshore Wind FarmSGLN Global Location Number With or Without ExtensionsSGTIN Serialised Global Trade Item NumberSSCC Serial Shipping Container CodeSPMT Self-Propelled Modular TransporterURIs Uniform Resource IdentifiersURL Uniform Resource Locator5 Supply chain processes: Planning, ordering and monitoring5.1 Genera