BS ISO 22555-2008 Ships and marine technology Propeller pitch indicators《船舶和航海技术 浆距指示器》.pdf

《BS ISO 22555-2008 Ships and marine technology Propeller pitch indicators《船舶和航海技术 浆距指示器》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 22555-2008 Ships and marine technology Propeller pitch indicators《船舶和航海技术 浆距指示器》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 22555:2007Ships and marine technology Propeller pitch indicatorsICS 47.020.70g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58

2、BS ISO 22555:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008ISBN 978 0 580 55826 9National forewordThis British Standard is the UK implementation of ISO 22555:2007.The UK participation in its preparation was entrust

3、ed to Technical Committee EPL/80, Maritime navigation and radiocommunication equipment and systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are resp

4、onsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsINTERNATIONALSTANDARDISO22555First edition2007-09-15Reference numberISO 22555:2007(E)Ships and marine technology Propeller p

5、itch indicatorsNavires et technologie maritime Indicateurs de pas du propulseurBS ISO 22555:2007ii iiiContents Page1 Scope 12 Normative references 13 Terms and definitions 14 Construction of indicator system 24.1 Indicator system 24.2 Transmitter . 24.3 Indicator . 25 Performance requirements . 35.1

6、 General . 35.2 Calibration accuracy . 35.3 Damping efficiency . 35.4 Power supply fluctuation 35.5 Insulation resistance and high voltage . 36 Methods of testing and required test results 46.1 Construction 46.2 Environmental test 46.3 Calibration test 46.4 Damping test 46.5 Power supply fluctuation

7、 test 47 Interface 48 Marking . 49 Information . 4Bibliography . 5BS ISO 22555:2007ivForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out throu

8、gh ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates

9、 closely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Dr

10、aft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this docume

11、nt may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 22555 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, SubcommitteeSC 6, Navigation.BS ISO 22555:20071Ships and marine technology Propeller pitch indic

12、ators1ScopeThis International Standard specifies the construction, performance requirements, methods of testing andrequired test results for the propeller pitch indicators (hereinafter referred to as “indicator system”) required byclause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000)

13、.This International Standard is associated with IMO Resolution A.694 (17) and IEC 60945.Where a requirement in this International Standard differs from IEC 60945, the requirement in this InternationalStandard takes precedence.2 Normative referencesThe following referenced documents are indispensable

14、 for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenced document(including any amendments) applies.IEC 60945, Maritime navigational and radiocommunication equipment and systems Generalrequirements Method

15、s of testing and required test resultsIEC 61162-1, Maritime navigation and radiocommunication equipment and systems Digital interfaces Part 1: Single talker and multiple listenersIEC 61162-2, Maritime navigation and radiocommunication equipment and systems Digital interfaces Part 2: Single talker an

16、d multiple listeners, high-speed transmission3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1 propeller pitch indicatorremote device capable of indicating the angular position of moving propeller blades between their maximumangular setting on ei

17、ther side of their neutral position on the equipment to which they are mounted3.2 indicatormeans by which the state of the equipment or machinery is represented to an observerNOTE An indicator shows both the sense and magnitude of the information it presents. An indicator can be analog ordigital.3.3

18、 analog type indicatorindicator that shows the pitch angle in a continuous way, such as by means of an arrow pointer and graduatedscaleBS ISO 22555:200723.4 digital type indicatorindicator that shows the pitch angle in a discrete, alphanumeric way3.5 calibration accuracydifference between the angle

19、registered by the transmitter and the angle indicated by an indicator3.6 damping efficiencytime elapsed for the indicated angle to match the angle of the transmitter shaft4 Construction of indicator system4.1 Indicator system4.1.1 An indicator system should show information on the state of the equip

20、ment or machinery to which it isconnected at locations adjacent to or remote from the equipment or machinery. At the equipment or machinery,such systems will generally comprise a sensor and transmitter; at the observers location, such systems willgenerally contain an indicator.In general, the system

21、 construction shall comply with the following requirements.4.1.2 The indicator system enclosures shall be robust and constructed so as to facilitate easy adjustment andmaintenance.4.1.3 The indicator system shall be provided with an earthing terminal or shall be so constructed as to becapable of bei

22、ng connected to an electrical earth.4.1.4 An analog type indicator can be used as indicator(s) of the indicator system. It may be additionallyprovided by a digital type if fitted.4.2 TransmitterThe transmitter shall be driven by suitable means from the controllable pitch propeller activating mechani

23、sm.4.3 Indicator4.3.1 An analog indicator shall be of a centre-zero type (preferably circular). Where a circular scale indicator isused, the zero position shall be uppermost.The direction “Ahead” or “Starboard” shall be to the right of the zero graduation; the directions “Astern” or “Port”shall be t

24、o the left of the zero graduation.4.3.2 The digital indicator shall indicate the pitch angle as readily legible digital figures preceded by a symbolor letter(s) indicating direction. The directions “Ahead” or “Starboard” shall be identified by the “plus” sign or bythe letters “AH (ST)”, while “Aster

25、n” or “Port” shall be identified by a “minus” sign or by the letters “AS (PT)”.4.3.3 The maximum angle indicated shall be the same for both Ahead/Starboard and Astern/Port and shall beno less than .4.3.4 Scale graduations shall be no smaller than . Graduation marks corresponding to increments shallb

26、e more prominent than those for intervening increments.4.3.5 The pointer of an indicator shall be capable of being adjusted to zero.4015BS ISO 22555:200734.3.6 The letters and graduations on the dial shall be such that the direction of ahead and astern can be clearlydistinguished.4.3.7 All illuminat

27、ion and lighting of an indicator shall be adjustable down to zero, except the control of thedimmers which shall remain readable.4.3.8 The illumination and lighting of an indicator shall be arranged in order not to hinder an operators visionat night and in order to make the scale, pointer and letters

28、 as equally visible as possible, even in dim light or thedark.5 Performance requirements5.1 GeneralThe transmitter shall have the capacity to satisfy the requirements specified in 5.2, 5.3 and 5.4 when allconnected indicators are operating simultaneously. The manufacturer shall clearly state the max

29、imum numberof indicator(s) or the capacity of connected indicator(s) that can be supported by a transmitter.5.2 Calibration accuracyTo calibrate the indicator system, the shaft of a transmitter is gradually rotated from the zero position to themaximum angle ahead (Starboard) or astern (Port), and th

30、e angles shown by an indicator are recorded everyof rotation. The difference between the angle of the transmitter shaft and the corresponding value shown atan indicator shall be within of the sum of the maximum angle in both directions.5.3 Damping efficiencyIf a voltage is suddenly applied while the

31、 transmitter shaft is approximately at half of full-scale position and theindicator pointer is set to the zero position, the pointer shall be reset to that position within or less.5.4 Power supply fluctuation5.4.1 The performance specified in 5.1 and 5.2 shall be maintained when the system is subjec

32、t to the powersupply fluctuations.5.4.2 After repeated makings and breakings, the designated performance shall be demonstrated withoutcarrying out manual adjustments.5.4.3 When the rated voltage and frequency are subjected to the combinations of fluctuations, as given inTable 1, the designated perfo

33、rmance shall be demonstrated.5.5 Insulation resistance and high voltageWhen insulation resistance and high voltage tests are to be carried out, IEC 60092-504 may be applied.Table 1 Fluctuation rate of the rated voltage and frequencySettled conditionVoltage fluctuationFluctuating period: Frequency fl

34、uctuationTransient conditionVoltage fluctuationFluctuating period: Frequency fluctuation51,5 %5s 10 %600 s 5% 20 %3s 10 %BS ISO 22555:200746 Methods of testing and required test results6.1 ConstructionThe construction of an indicator system shall comply with the requirements specified in Clause 4.6.

35、2 Environmental testUnless otherwise stated in this International Standard, all the tests shall be carried out according to therequirements of IEC 60945. The manufacturer shall determine which components of the indicator system will beprotected or exposed, as defined in IEC 60945.6.3 Calibration tes

36、tThe calibration test shall be carried out in accordance with 5.2 and shall satisfy the requirements specifiedtherein.6.4 Damping testThe damping test shall be carried out in accordance with 5.3 and shall satisfy the requirements specifiedtherein.6.5 Power supply fluctuation testThe power supply flu

37、ctuation test shall be carried out in accordance with 5.4 and shall satisfy the requirementsspecified therein.7InterfaceWhen the indicator system provides interface facilities, they shall meet the requirements of the appropriateinternational marine interface standards IEC 61162-1 and IEC 61162-2.8 M

38、arking8.1 Each unit of an indicator system shall be marked with the following: identification of the manufacturer; equipment type number or model identification number under which it was type tested; serial number of the unit.8.2 Each unit shall be marked with the minimum safe distance from a magnet

39、ic compass at which it may bemounted (for bridge installation). The safe distance shall be measured in accordance with IEC 60945.9 InformationThe manufacturer shall provide adequate equipment documentation to enable competent members of a shipscrew to operate and maintain the equipment efficiently.B

40、S ISO 22555:20075Bibliography1 ISO 8468, Ships and marine technology Ships bridge layout and associated equipment Requirements and guidelines2 IEC 60092-504, Electrical installations in ships Part 504: Special features Control andinstrumentation3 International Convention for the Safety of Life at Se

41、a (SOLAS), 1974 (amended)4 IMO Resolution A.694 (17), General requirements for shipborne radio equipment forming part of theglobal maritime distress and safety system (GMDSS) and for electronic navigational aidsBS ISO 22555:2007BS ISO 22555:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standa

42、rds InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standa

43、rds should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical

44、committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standards

45、Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards,

46、 it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Expor

47、ters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developm

48、ents and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standar

49、ds Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,