BS ISO 21537-2-2005 Clamping flanges for superabrasive cutting-off wheels - Building and construction《超磨料切割砂轮用夹具法兰 建筑和施工》.pdf

《BS ISO 21537-2-2005 Clamping flanges for superabrasive cutting-off wheels - Building and construction《超磨料切割砂轮用夹具法兰 建筑和施工》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 21537-2-2005 Clamping flanges for superabrasive cutting-off wheels - Building and construction《超磨料切割砂轮用夹具法兰 建筑和施工》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 21537-2:2004 Clamping flanges for superabrasive cutting-off wheels Part 2: Building and construction ICS 25.100.70 BS ISO 21537-2:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 3 October 2005 BSI 3 October 2005 I

2、SBN 0 580 46644 2 National foreword This British Standard reproduces verbatim ISO 21537-2:2004 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper and cloths, and powders, which has

3、 the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “Inte

4、rnational Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a B

5、ritish Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and

6、 European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates

7、when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 21537-2:2004(E)INTERNATIONAL STANDARD ISO 21537-2 First edition 2004-10-15 Clamping flanges for superabrasive cutting-off wheels Part 2: Building and construction Flasques pour meules d

8、e trononnage superabrasives Partie 2: Btiment et gnie civil BS ISO 21537-2:2004ii BS ISO 21537-2:2004 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is norm

9、ally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in t

10、he work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare

11、 International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some

12、 of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21537-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. ISO 21537 consists of the

13、following parts, under the general title Clamping flanges for superabrasive cutting- off wheels: Part 1: Natural stone Part 2: Building and construction blank1Clamping flanges for superabrasive cutting-off wheels Part 2: Building and construction 1 Scope This part of ISO 21537 specifies dimensions f

14、or clamping flanges for the mounting of superabrasive cutting-off wheels (diamond saws) for use on stationary cutting-off machines, mobile cutting-off machines and hand-held cutting-off machines for the cutting of mineral materials. 2 Normative references The following referenced documents are indis

15、pensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without i

16、ndividual tolerance indications 3 Dimensions 3.1 General The dimensions of flanges used on hand-held cutting-off machines (type A), on masonry cutting-off machines (type B), on joint cutting machines (type C), on joint cutting machines (flush cuts) (type D) and on wall cutting- off machines (type E)

17、 for clamping suerabrasive cutting-off wheels are shown in Figures 1 to 5 and given in Tables 1 to 5 respectively. Details which are not specified shall be chosen according to need. BS ISO 21537-2:2004BS ISO 21537-2:2004 2 3.2 Type A aOptional drive pin for cutting-off wheels D 230 mm. Figure 1 Type

18、 A Table 1 Dimensions of clamping flanges for type A Dimensions in millimetres General tolerances ISO 2768 - m Cutting-off wheel Flange D Fb c d 2d 3d 4P 1r D H min. H7 g6 0,1 D u 100 16 16 115 u D u 230 22,23 41 22,23 5 20 20 22,23 22,23 230 D u 400 25,4 72 6 1 25,4 11,5 57,4 10 33.3 Type B aOption

19、al drive pin. Figure 2 Type B Table 2 Dimensions of clamping flanges for type B Dimensions in millimetres General tolerances ISO 2768 - m Cutting-off wheel Flange D H D Fb c d 2d 3d 4P 1r Size min. H7 g6 0,1 Number of pins 20 1 20 20 D u 250 25,4 2 41 25,4 25,4 5 25,4 3 25,4 25,4 250 D u 400 30 4 72

20、 8 30 30 10 25,4 5 25,4 25,4 400 D u 700 60 6 90 60 60 57,4 1 7 100 3 120 25,4 8 25,4 25,4 120 1 9 120 1 700 D u 900 60 10 140 60 60 100 3 120 11 120 1 25,4 12 25,4 25,4 100 3 120 13 120 1 900 D u 1 000 60 14 162 12 1 60 60 11,5 100 12 3 120 BS ISO 21537-2:20044 3.4 Type C Figure 3 Type C Table 3 Di

21、mensions of clamping flanges for type C Dimensions in millimetres General tolerances ISO 2768 - m Cutting-off wheel Flange D H D Fb c d 2d 3d 4P 1r min. H7 e8 0,1 Number of pins D u 350 25,4 80 25,4 10 25,4 25,4 350 D u 500 35 90 8 35 25,4 25,4 500 D u 900 35 140 12 1 35 12 25,4 25,4 35 35 57,4 900

22、D u 1 500 50 198 16 1,5 50 11,5 20 1 BS ISO 21537-2:200453.5 Type D a6 60 Figure 4 Table 4 Dimensions of hub flanges for type D Dimensions in millimetres General tolerances ISO 2768 - m Cutting-off wheel Flange D H D Fb e d 1d 3P 10 0,1 e8 and number of threaded holes 0,1 25,4 25,4 35 35 D u 700 50

23、110 10 3 50 25,4 25,4 35 35 90 700 D u 1 200 50 140 12 3,5 50 M8 6 60 110 25,4 25,4 35 35 1 200 D u 1 500 50 198 16 3,5 50 M8 or M12 6 60 120 BS ISO 21537-2:20046 3.6 Type E Figure 5 Type E BS ISO 21537-2:20047Table 5 Dimensions of hub flanges for type E Dimensions in millimetres General tolerances

24、ISO 2768 - m Cutting-off wheel Flange D H D F e b c d 1d 2d 3P 2r 0,1 min. 0 1 , 0 min. H7 e8 and number of threaded holes 45 60 80 90 110 125 13025,4 55 25,4 M5 4 90 X 12 D u 400 35 80 1,6 8 35 M6 6 60 X 25,4 25,4 35 35 50 50 400 D u 1 000 60 110 2 10 1 60 M8 6 60 X 16 25,4 25,4 X 35 35 50 50 1 000

25、 D u 1 600 60 127 3,5 60 M8 6 60 X X 25 25,4 25,4 X 35 35 50 50 1 600 D u 2 000 60 148 3,5 12 1,5 60 M8 6 60 X X X X 35 4 Requirements 4.1 Material Specifies to the manufacturers choice, elastic limit for steel at least 300 MPa. 4.2 Design Clamping flanges of types A1 to C3 are to be used in pairs i

26、n the combinations A1/A3, B1/B3, C1/C3, A2/A3, B2/B3 or C2/C3. Types A2, B2 and C2 are equipped on the rear side with a closed driving pin for a connection to the wheel spindle which is resistant to torque. For clamping flanges of types A to C the drive pins shall not project beyond the clamping fla

27、nge. 4.3 Supply schedule The supply schedule of the clamping flanges types A to C comprise a fixed and a loose flange. For flanges types A, B and C, the drive pins are pressed into the fixed flange. The supply schedule of hub flanges type D comprises hexagon socket countersunk screws. The supply sch

28、edule of hub flange E comprises hexagon screws threaded up to the head and additional hexagon socket countersunk screws. Only the screws intended by the machine manufacturer shall be used. BS ISO 21537-2:20048 5 Designation EXAMPLE A clamping flange type B1 for use on superabrasive cutting-off wheel

29、s, outisde diameter D = 700 mm and size 9 is designated as follows: Flange ISO 21537-2 - B1 - 700 9 6 Marking Clamping flanges according with this part of ISO 12537 shall be indelibly marked with the following data: “Maximum diameter of the superabrasive cutting-off wheel intended for the relevant c

30、utting-off machine.” BS ISO 21537-2:2004blankBS ISO 21537-2:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level.

31、 It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grat

32、eful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual up

33、dating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email:

34、 ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI prov

35、ides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:

36、 +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20

37、8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI pu

38、blications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic

39、, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.