BS ISO 20326-2016 Resilient floor coverings Specification for floor panels assembly for loose laying《弹性地板覆盖物 松铺层地板镶板 总成规格》.pdf

《BS ISO 20326-2016 Resilient floor coverings Specification for floor panels assembly for loose laying《弹性地板覆盖物 松铺层地板镶板 总成规格》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 20326-2016 Resilient floor coverings Specification for floor panels assembly for loose laying《弹性地板覆盖物 松铺层地板镶板 总成规格》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 20326:2016Resilient floor coverings Specification for floor panels/assembly for loose layingBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 20326:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 20326:2016.The

2、UK participation in its preparation was entrusted to Technical Committee PRI/60, Resilient and Laminate Floor Coverings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 89155 7 ICS 97.150 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the aut

4、hority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 20326:2016 ISO 2016Resilient floor coverings Specification for floor panels/assembly for loose layingRevtements de sol rsilients Spcifications de

5、s panneaux de plancher/assemblages pour pose flottanteINTERNATIONAL STANDARDISO20326First edition2016-12-15Reference numberISO 20326:2016(E)BS ISO 20326:2016ISO 20326:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless othe

6、rwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

7、below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 20326:2016ISO 20326:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and

8、definitions . 24 Requirements 34.1 Requirements for the floor panels . 34.2 General requirements for the surface layer . 34.2.1 Residual indentation 34.2.2 Colour fastness to artificial light 44.2.3 Hardness of a rubber surface layer 45 Classification 45.1 General classification requirements . 45.2

9、Classification requirements for the surface layer . 55.2.1 General 55.2.2 Linoleum surface layer . 55.2.3 Rubber surface layer . 55.2.4 Polyvinyl chloride surface layer 55.2.5 Polyvinyl chloride with enhanced slip properties surface layer 55.2.6 Synthetic thermoplastic polymer surface layer 55.2.7 C

10、ork surface layer . 65.2.8 Heterogeneous polyurethane surface layer 66 Marking, labelling and packaging 66.1 Marking and labelling . 66.2 Packaging . 6Annex A (normative) Determination of flatness 7Annex B (normative) Determination of openings and height differences between floor panels 10Annex C (n

11、ormative) Determination of dimensional variations caused by changes in humidity .12Annex D (normative) Determination of locking strength with a tensile testing machine .14Annex E (normative) Test report .16Annex F (informative) Optional properties 17Bibliography .18 ISO 2016 All rights reserved iiiC

12、ontents PageBS ISO 20326:2016ISO 20326:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each memb

13、er body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Ele

14、ctrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types

15、of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be hel

16、d responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information

17、 given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers

18、to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 219, Floor coverings.iv ISO 2016 All rights reservedBS ISO 20326:2016INTERNATIONAL STANDARD ISO 20326:2016(E)Resilient floor coverings Specification for floor panels/assembly for

19、 loose laying1 ScopeThis document specifies requirements and test methods for floor panels/assembly for domestic and commercial levels of use, which have surface layers consisting of resilient floor covering.This document is not applicable to heterogeneous polyvinyl chloride floor panels/assembly fo

20、r floating installation covered by ISO 10582 or to floor panels/assembly that are subject to frequent wetting, such as bathrooms, laundry rooms and saunas.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirement

21、s of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 4918, Resilient, textile and laminate floor coverings Castor chair testISO 10581, Resilient floor coverings Homogeneo

22、us poly(vinyl chloride) floor covering SpecificationsISO 10582, Resilient floor coverings Heterogeneous polyvinyl chloride floor coverings SpecificationISO 10874, Resilient, textile and laminate floor coverings ClassificationISO 10577, Resilient floor coverings Specification for rubber sheet floor c

23、overings without backing.ISO 16581, Resilient and laminate floor coverings Determination of the effect of simulated movement of a furniture legISO 16905, Resilient floor coverings Specification for rubber floor covering Tile/PlankISO 19322, Resilient floor coverings Specification for floor coverings

24、 based on thermoplastic polymersISO 24011, Resilient floor coverings Specification for plain and decorative linoleumISO 24334, Laminate floor coverings Determination of locking strength for mechanically assembled panelsISO 24336, Laminate floor coverings Determination of thickness swelling after par

25、tial immersion in waterISO 24342, Resilient and textile floor-coverings Determination of side length, edge straightness and squareness of tilesISO 24346, Resilient floor coverings Determination of overall thicknessISO 26986, Resilient floor coverings Expanded (cushioned) poly(vinyl chloride) floor c

26、overing SpecificationEN 651, Resilient floor coverings Polyvinyl chloride floor coverings with foam layer SpecificationEN 652, Resilient floor coverings Polyvinyl chloride floor coverings with cork-based backing SpecificationEN 655, Resilient floor coverings Tiles of agglomerated composition cork wi

27、th polyvinyl chloride wear layer Specification ISO 2016 All rights reserved 1BS ISO 20326:2016ISO 20326:2016(E)EN 12104, Resilient floor coverings Cork floor tiles SpecificationEN 13845, Resilient floor coverings Polyvinyl chloride floor coverings with particle based enhanced slip resistance Specifi

28、cationEN 14565, Resilient floor coverings Floor coverings based upon synthetic thermoplastic polymers SpecificationEN 16776, Resilient floor coverings Heterogeneous polyurethane floor coverings SpecificationCEN/TS 16354, Laminate floor coverings Underlays Specification, requirements and test methods

29、3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available

30、at https:/www.iso.org/obp/3.1floor panelproduct generally of rectangular form consisting of a compact layer of a substrate and a surface layer of a resilient floor coveringNote 1 to entry: A backing might be included.3.2substratecore material of the floor panel with profiled edges to facilitate asse

31、mbly at installationNote 1 to entry: Examples are Medium Density Fibreboard (MDF), High Density Fibreboard (HDF) and Wood Plastic Composite (WPC) either with or without wood fiber.3.3surface layerupper decorative layer(s) of one of the following resilient floor coverings, bonded to the substrate dir

32、ectly or as total product and intended to be on the visible side when the floor is installed: linoleum floor covering (ISO 24011); rubber floor covering (ISO 10577 and ISO 16905); polyvinyl chloride floor covering (ISO 10581, ISO 10582, EN 651, EN 652 and ISO 26986); cork floor covering (EN 12104 an

33、d EN 655); synthetic thermoplastic polymer floor covering (EN 14565 and ISO 19322); polyvinyl chloride floor coverings with particle based enhanced slip resistance (EN 13845); heterogeneous polyurethane floor covering (EN 16776)3.4backinglayer beneath the surface layer on the back of the substrate,

34、e.g. cork, impregnated paper, foam2 ISO 2016 All rights reservedBS ISO 20326:2016ISO 20326:2016(E)4 Requirements4.1 Requirements for the floor panelsAll classes of floor panels including the surface layer shall conform to the requirements specified in Table 1 when tested in accordance with the speci

35、fied test methods.Table 1 General requirements for the floor panelsProperty Requirement Test methodDimensions measured at the surface layer Maximum deviation from the nominalISO 24342Square panels Side length % 0,10Rectangular panels Width % 0,10Length mm 0,5Overall thickness ISO 24346Average mm Nom

36、inal 0,25Individual values mm Maximum deviation from the average 0,30Squareness mm 0,20 ISO 24342Straightness measured at the surface layermm 0,30ISO 24342aFlatness of the panel Annex ALength Concave/convex % of the length 0,50/1,0Width Concave/convex % of the width 0,10/0,15Openings between panels

37、Annex BAverage mm 0,15Individual values mm 0,20Height difference between panels Annex BAverage mm 0,10Individual values mm 0,15Dimensional variation caused by changes in atmospheric humidity %0,25 Annex CaFor length 0,5 m, a metal ruler may be used.4.2 General requirements for the surface layerAll c

38、lasses of floor panels shall conform to the appropriate requirements as specified below.4.2.1 Residual indentationSurface layers in accordance with ISO 24011, ISO 10581, ISO 10582, EN 13845, EN 14565 and EN 16776 shall conform to the respectively residual indentation requirements in these particular

39、 standards.NOTE The residual indentation requirements for EN 651, EN 652, EN 655, EN 12104, ISO 19322 and ISO 26986 are related to the surface or wear layer thickness classes in that same standard, and are specified in 5.2. ISO 2016 All rights reserved 3BS ISO 20326:2016ISO 20326:2016(E)4.2.2 Colour

40、 fastness to artificial lightThe colour fastness to artificial light shall be in accordance with the requirements for the surface or wear layer established in the applicable specification standard (as listed in 3.3).4.2.3 Hardness of a rubber surface layerThe hardness of a rubber surface layer shall

41、 comply with the requirements specified in ISO 10577 or ISO 16905.5 ClassificationThe classification scheme for resilient floor coverings panels for loose laying is specified in ISO 10874. To classify for a certain use classification, the panels shall conform the relevant requirements for that class

42、ification in both 5.1 and 5.2. If not the same level of classification is achieved, the worst result is decisive.5.1 General classification requirementsThe panels shall conform to the requirements of Table 2 for their class, regardless of their surface layer material.Table 2 Classification requireme

43、nts for floor panelsClass Symbol Intensity of useEffect of a furniture legaEffect of a castor chairbLocking strength ThicknessswellingDomestic21 Moderate/ LightNo requirementNo requirementNo requirement20 %22 General/ Medium22+ General23 Heavy No distur-bance to the surface other than slight change

44、in ap-pearance and no delaminat-ing shall occurCommercial Hydroscopic substratecOther substratesaFor panels with a cork surface, the requirements for the furniture leg in EN 655 or EN 12104 shall apply.bThe product shall be tested with the pre-attached backing or the prescribed underlay by manufactu

45、rer. In case no underlay is prescribed, the product shall be tested with an underlay with thickness = (2 0,5) mm and compressive stress CS = (60 10) kPa in accordance with CEN/TS 16354.cOnly for panels with substrates with hygroscopic properties, e.g. HDF or MDF.4 ISO 2016 All rights reservedBS ISO

46、20326:2016ISO 20326:2016(E)Class Symbol Intensity of useEffect of a furniture legaEffect of a castor chairbLocking strength Thicknessswelling31 Moderate No damage shall be visible when tested with foot type 0No distur-bance to the surface other than slight change in ap-pearance and no delaminat-ing

47、shall occurNo requirement18 %32 General Long side1,0 kN/mShort side2,0 kN/mBoth sides1,5 kN/m33 Heavy15 %34 Very Heavy Both sides3,5 kN/mBoth sides2,0 kN/mTest method ISO 16581 ISO 4918 ISO 24334 Annex D ISO 24336aFor panels with a cork surface, the requirements for the furniture leg in EN 655 or EN

48、 12104 shall apply.bThe product shall be tested with the pre-attached backing or the prescribed underlay by manufacturer. In case no underlay is prescribed, the product shall be tested with an underlay with thickness = (2 0,5) mm and compressive stress CS = (60 10) kPa in accordance with CEN/TS 1635

49、4.cOnly for panels with substrates with hygroscopic properties, e.g. HDF or MDF.5.2 Classification requirements for the surface layer5.2.1 GeneralThe surface layer shall be classified in accordance with ISO 10874. The classification depends on the type of floor covering used.5.2.2 Linoleum surface layerFloor panels with a linoleum surface layer shall conform to the classification