BS ISO 2020-2-1997 Aerospace - Preformed flexible steel wire rope for aircraft controls - Technical specification《航空航天 飞机控制装置的预成形挠性钢丝绳 第2部分 技术规范》.pdf

《BS ISO 2020-2-1997 Aerospace - Preformed flexible steel wire rope for aircraft controls - Technical specification《航空航天 飞机控制装置的预成形挠性钢丝绳 第2部分 技术规范》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 2020-2-1997 Aerospace - Preformed flexible steel wire rope for aircraft controls - Technical specification《航空航天 飞机控制装置的预成形挠性钢丝绳 第2部分 技术规范》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO2020-2:1997Aerospace Preformed flexible steel wire rope for aircraft controlsPart2: Technical specificationICS 49.035BSISO2020-2:1997This BritishStandard, having been prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards

2、Board and comesinto effect on15October1997 BSI03-2000ISBN 0 580 28744 0National forewordThis BritishStandard reproduces verbatim ISO2020-2:1997 and implements it as the UK national standard.The UK participation in its preparation was entrusted to Technical Committee ACE/14, Aerospace details and par

3、ts, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulg

4、ate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe BritishStandards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section

5、entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.Compl

6、iance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, pagesi andii, theISO title page, pages ii to iv, pages1 to9 and a back cover.This standard has been updated (see copyright date) and m

7、ay have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.Amendments issued since publicationAmd. No. Date CommentsBSISO2020-2:1997 BSI 03-2000 iContentsPageNational foreword Inside front coverForeword iiiText of ISO2020-2 1ii blankBS ISO2020-2:1997

8、ii BSI 03-2000ContentsPageForeword iii1 Scope 12 Normative references 13 General requirements 14 General inspections and tests 15 Specific requirements, inspections and test methods 26 Re-test 47 Quality assurance 57.1 Quality assurance and management system 57.2 Product qualification testing approv

9、al 57.3 Certificate of conformity 58 Delivery, packing and marking 58.1 Delivery 58.2 Packing 58.2.1 Ordinary packing 58.2.2 Special packing 58.3 Marking 69 Test equipment for endurance test 6Figure 1 Apparatus for endurance test 7Figure 2 Test pulleys for use in endurance test 8Table 1 Breaking loa

10、d after endurance test and permissibleincrease in diameter 5Table 2 9Descriptors: Aircraft industry, aircraft equipment, control devices, steel products, wire, wire rope, tests, mechanical tests, acceptance testing, inspection, marking, packaging.BS ISO2020-2:1997 BSI 03-2000 iiiForewordISO (the Int

11、ernational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee ha

12、s been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical

13、standardization.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vote.International Standard ISO2020-2 was prepared by Technical C

14、ommitteeISO/TC20, Aircraft and space vehicles, Subcommittee SC12, Mechanical system parts.This first edition of ISO2020-2 together with ISO2020-1 cancels and replaces ISO2020:1984.ISO2020 consists of the following parts, under the general title Aerospace Preformed flexible steel wire rope for aircra

15、ft controls: Part1: Dimensions and loads; Part2: Technical specification.iv blankBS ISO2020-2:1997 BSI 03-2000 11 ScopeThis part of ISO2020, in conjunction with ISO2020-1, specifies the inspections and tests as well as acceptance and qualification conditions for preformed flexible steel wire ropes f

16、or aircraft controls.2 Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO2020. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements

17、based on this part of ISO2020 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.ISO2020-1:1997, Aerospace Preformed flexible steel wire rope for air

18、craft controls Part1: Dimensions and loads. ISO2408:1985, Steel wire ropes for general purposes Characteristics. ISO9001:1994, Quality systems Model for quality assurance in design, development, production, installation and servicing. ISO9002:1994, Quality systems Model for quality assurance in prod

19、uction, installation and servicing. 3 General requirementsManufacture and workmanship shall be in accordance with the best practice for high quality aircraft wire ropes consistent with the requirements of this part of ISO2020. The finished cable shall be uniform in construction and securely laid, fr

20、ee from kinks, loose wires, loose strands or other defects. A maximum of one broken wire is permissible on a rope length of300mm.Tucked joints may be in wires of diameter equal to or less than0,2mm. For wires of diameter greater than0,2mm the joints shall be made by brazing or electric welding. In t

21、he same strand, joints shall be not less than6m apart.4 General inspections and testsAll wire rope shall be examined for workmanship and finish to determine compliance. For this purpose, the wire rope shall travel no faster than30m/min and shall be stopped for closer inspection when necessary. This

22、inspection shall take place at the time the wire rope is wound on shipping reels. Any discard from the head or starting end of the manufacturing reel shall be removed prior to winding of the shipping reel.The manufacturer shall make available the necessary equipment for testing a rope to the conditi

23、ons of this part of ISO2020.Before every inspection and test the inspector shall be satisfied that the measuring instruments are correctly calibrated. Inspections and tests referred to in5.1 to5.10 shall be carried out on each lot produced.BS ISO2020-2:19972 BSI 03-20005 Specific requirements, inspe

24、ctions and test methodsSpecific requirements, inspections and test methods are given in5.1 to5.10. No. Characteristics Requirements Inspections and test methods Qa Aa5.1 Materials In accordance with ISO2020-1. Chemical analysis or certificate of conformity of the manufacturer of the semi-finished pr

25、oduct. 5.2 Dimensions In accordance with ISO2020-1. The actual diameter of the rope shall be measured after production with a measuring device with jaws broad enough to cover not less than two adjacent strands. At each of three points spaced at least1m apart, two measurements shall be taken at right

26、 angles to each other. The average of these six measurements shall fall within the specified maximum and minimum diameters. Each end of each manufactured length shall be measured in this manner. These measurements shall be made on a straight portion of the rope under no tension. 5.3 Masses In accord

27、ance with ISO2020-1. Using a suitable method. 5.4 Lubrication During rope manufacture a suitable lubricant shall be applied so that each wire is coated. The lubricant shall reduce internal friction and inhibit corrosion. It shall be resistant in the service temperature range and shall have good lubr

28、ication properties.Visual examination and certificate of conformity of the grease manufacturer. 5.5 Surfaces Flattening of wire surfaces of the rope due to manufacture are permissible as long as the requirements of ISO2020-1 are met.Visual examination. 5.5.1 Surface treatment of zinc coated ropesThe

29、 requirements of ISO2020-1 shall be met.Testing according to theKeller-Bohaczek method. 5.6 Preforming The increase in the diameter of the wire rope after cutting shall not exceed the value indicated in Table 1.It shall be possible to lead the cut end through a bore with the maximum permissible diam

30、eter. Other suitable measuring methods, e.g.profile projectors or measuring magnifiers, are permissible.To avoid distorting the cable ends, it is recommended that cutting be carried out electrically or using cutters with constricting jaws. BS ISO2020-2:1997 BSI 03-2000 3No. Characteristics Requireme

31、nts Inspections and test methods Qa Aa5.7 Actual breaking loadThe minimum breaking load according to ISO2020-1 shall be met.The actual breaking load of the wire rope shall be determined in accordance with ISO3108. 5.8 Elongation The requirements of ISO2020-1 shall be met.From each wire rope of the7

32、7 and7 19 constructions a sufficient length shall be selected to provide an unobstructed minimum test length of500mm between the jaws of the test machine. This test length shall be progressively loaded(max.10mm/min) until60% of the minimum breaking load is reached. This load shall be maintained for1

33、min. It shall then be released to2% of the minimum breaking load. Under this initial load a gauge length of250mm shall be marked or another suitable measuring device with a minimum distance of100mm between cutting edges shall be applied. The rope shall then be progressively loaded(max.10mm/min) unti

34、l60% of its minimum breaking load is reached and its elongation determined when5%,10%,25%,40% and60% of the minimum breaking load are reached. 5.9 Shear proof testAfter testing no single wire shall be broken.Using the same test piece as for the elongation test the load shall be progressively increas

35、ed until a value of80% of the minimum breaking load is reached and maintained for a minimum period of5s. This load shall then be released and the test piece completely separated into its constituent wires and each wire shall be examined. NOTEThe manufacturer may use, at his discretion, electronic de

36、vices which have been developed to detect the breaking of wires while the test is being carried out. However in the event of any conflict of evidence, the test method described shall be used as the reference method. BS ISO2020-2:19974 BSI 03-20006 Re-testIf the requirements of an inspection or test

37、method are not met, a re-test may be carried out taking two further test lengths from the end of the same production length. If both test lengths conform to the requirements of this part of ISO2020, the relevant lot of wire rope shall be deemed to comply with requirements of this part of ISO2020. A

38、complete report of the tests shall be prepared and supplied with the dispatch documents for each test lot. No. Characteristics Requirements Inspections and test methods Qa Aa5.10 Endurance testAfter endurance testing and the subsequent test according to subclause4.5 the values of the minimum breakin

39、g load shall be met.An endurance test shall be carried out for each lot of wire rope. The number of reversals and the wire rope test load shall be as indicated in Table 1. The test apparatus shall conform to Figure 1. The total travel of the cable in one direction shall be343mm. The test pulleys sha

40、ll be made of steel and shall conform to the dimensions of Figure 2 andTable 2. The application of lubricant to the endurance test sample, in addition to the lubricant applied during the manufacture of wire rope, shall not be permitted either before or during the endurance test. After endurance test

41、ing the breaking load of the wire rope shall be rechecked in accordance with 4.7 as follows: a) the test length shall be that portion of the wire rope that passes over the test pulley during the endurance test;b) the breaking load shall, as a minimum, conform to the values specified in Table 1. a A=

42、Acceptance test, Q=Qualification testBS ISO2020-2:1997 BSI 03-2000 5Table 1 Breaking load after endurance test and permissible increase in diameter7 Quality assurance7.1 Quality assurance and management systemThe manufacturer shall proceed on the basis of a quality assurance and management system in

43、 accordance with ISO9001 or ISO9002 which has been certified by an approved authority. The certification has to be presented to the airworthiness authority of the receiving country or to the appointed representatives on their request.7.2 Product qualification testing approvalThe qualification approv

44、al test shall consist of all the tests specified in clause5.7.3 Certificate of conformityEach lot of wire rope supplied in conformity with this part of ISO2020 shall be accompanied by a certificate of conformity.8 Delivery, packing and marking8.1 DeliveryEach consignment shall consist of a maximum o

45、f6000m wire rope of the same construction and the same diameter produced in one production run on one or a series of successive machines.Ropes shall be delivered in minimum lengths of300m, except that up to20% of the rope ordered may be supplied in lengths between150m and300m.8.2 Packing8.2.1 Ordina

46、ry packingThe rope shall be wound on a suitable reel. The diameter of the barrel of the reel shall exceed40times the diameter of the rope. The flanges and the barrel of the reel shall be covered with waterproof material before the rope is wound onto the reel. When it is fully wound, the exposed surf

47、ace shall be covered with a layer of waterproof material held down by appropriate means.8.2.2 Special packingAny special packing shall be specified in the order.Nominal diameter of wire ropemmConstruction Wire rope test loadamin.NNumber of reversalsbMinimum breaking load Maximum rope diameter after

48、performing testmmfor carbon steelc kNfor corrosion-resisting steeld kN1,27 713,5700000,60 0,70 1,601,6 22 1,07 1,28 2,102,4 40 2,05 2,45 2,957 192,253,2 80 4,45 4,7 3,854,0 1071300006,25 6,4 4,854,8 165 9,30 9,9 5,755,6 225 12,45 13,4 6,556,4 285 15,60 17,0 7,407,2 350 17,80 20,8 8,308,0 400 21,80 2

49、4,0 9,159,5 535 32,05 32,0 10,85a The wire rope test load is equal to one half the weight which includes idler pulley and hanger.b 1cycle=2 reversals.c Minimum breaking load equal to50% of the original minimum breaking load, prior to the endurance test.d Minimum breaking load equal to60% of the original minimum breaking load, prior to the endurance test.BS ISO2020-2:19976 BSI 03-20008.3 MarkingA label shall be fixed on the reel bearing the following information:a) the designation in accordance with ISO2020-1;b) the name of the manu