BS ISO 1704-2008 Ships and marine technology - Stud-link anchor chains《船舶和海洋技术 链档环锚链》.pdf

《BS ISO 1704-2008 Ships and marine technology - Stud-link anchor chains《船舶和海洋技术 链档环锚链》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1704-2008 Ships and marine technology - Stud-link anchor chains《船舶和海洋技术 链档环锚链》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS ISO 1704:2008Ships and marine technology Stud-link anchor chainsICS 47.020.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS I

2、SO 1704:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008ISBN 978 0 580 54022 6National forewordThis British Standard is the UK implementation of ISO 1704:2008.The UK participation in its preparation was entrusted by

3、Technical Committee SME/32, Ships and marine technology Steering committee, to Panel SME/32/-/4, Ships and marine technology Outfitting and deck machinery.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include al

4、l the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsReference numberISO 1704:2008(E)INTERNATIONAL STANDARD ISO1704Third

5、edition2008-03-01Ships and marine technology Stud-link anchor chains Navires et technologie maritime Chanes dancre mailles tanonnes BS ISO 1704:2008ii iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Shape and dimensions. 2 4.1 Shape . 2 4.2 Dimensions

6、 2 5 Tolerances . 3 5.1 Nominal diameter of common stud links .3 5.2 Length of five links . 3 5.3 All other dimensions 3 6 Range of sizes of links and shackles . 4 7 Designation of size . 4 8 Connections 4 BS ISO 1704:2008iv Foreword ISO (the International Organization for Standardization) is a worl

7、dwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on

8、that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted i

9、n accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard

10、 requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1704 was prepared by Tec

11、hnical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery. This third edition cancels and replaces the second edition (ISO 1704:1991) which has been technically revised as follows. Tolerances on the nominal diameter of the links remain the same, but tol

12、erances on other parts of the links have been appropriately adjusted. Lengths and tolerances of the combined links have been increased. The allowable manufacturing tolerance of all other dimensions has been increased. The nominal diameter of a common stud link is shown by d and the diameter of other

13、 links, shackles and swivels given as multiples of d. The swivel type and a series of its dimensions have been added for the convenience of the user. The patented swivel or the swivel with a particular function can be used as a substitute if this is possible in harmony with this International Standa

14、rd. BS ISO 1704:20081Ships and marine technology Stud-link anchor chains 1 Scope This International Standard specifies the shape, proportions, dimensions and tolerances of the component parts of stud-link anchor chains. Any statutory requirements, rules and regulations applicable to the individual s

15、hip concerned also apply. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

16、ISO 2093:1986, Electroplated coatings of tin Specification and test methods ISO 2339:1986, Taper pins, unhardened ISO 3828:1984, Shipbuilding and marine structures Deck machinery Vocabulary 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 chai

17、n-shot component of an anchor chain consisting of common stud links and joining shackles with a given nominal length (27,5 m or 25 m) in accordance with ISO 3828 3.2 common stud link basic link of which chain-shot consists 3.3 enlarged stud link strengthened link that connects a common stud link and

18、 the end link, in the case of connecting chain-shots, with a “D” type joining shackle, or connects a common stud link and swivel 3.4 end link strengthened link that is attached to the ends of chain-shots, in the case of connecting chain-shots, with “D” type joining shackles or the outboard chain-sho

19、t with an end shackle 3.5 joining shackle “D” type joining shackle or Kenter type joining shackle used for connecting chain-shots BS ISO 1704:20082 3.6 end shackle enlarged shackle used for connecting the outboard chain-shot to the anchor 3.7 swivel movable component of the outboard chain-shot which

20、 prevents excessive twisting of the chain cable 3.8 outboard chain-shot additional short chain-shot fastened to the anchor shackle 3.9 nominal size nominal diameter of the common stud link 4 Shape and dimensions 4.1 Shape The stud links, shackles and component parts shall be of the shapes and propor

21、tions shown in Figures 1 to 9. 4.2 Dimensions 4.2.1 General The dimensions of stud links, shackles and component parts shall be in accordance with the values given in Tables 1 to 7. The nominal diameter, d, is a design diameter measured at the crown of a common stud link as an average value of two m

22、easurements perpendicular to each other. See Figure 1 and Table 1. All dimensions, based on the nominal diameters, d, of the common stud links, shall be measured after the chain and shackles have been subjected to the statutory proof loads. 4.2.2 Enlarged stud links The proportions of the enlarged s

23、tud links are the same as those of the common stud links. The nominal diameter of the enlarged stud link is 10 % larger than the nominal diameter of the common stud link: d1= 1,1 d, the calculated values are rounded to the nearest nominal diameter of the common link. 4.2.3 Common stud links and enla

24、rged stud links The inside diameter of common stud links and enlarged stud links shall be sufficient to allow each link to bed properly and work freely. See Figures 1 and 2. 4.2.4 End links The inside diameter of end links shall be sufficient to allow the shackle link to bed properly and work freely

25、. See Figure 3. The nominal diameter of the end link is 20 % larger than the nominal diameter of the common stud link: d2= 1,2 d, the calculated values are rounded to the nearest nominal diameter of the common link. 4.2.5 Shackle retaining pin The retaining pin used in “D” type joining shackles and

26、end shackles shall be a taper pin having a taper of not less than 1:50 and not more than 1:16 on the diameter. BS ISO 1704:20083The retaining pin used in Kenter type shackles shall be a taper pin having a taper of not less than 1:50 and not more than 1:32 on the diameter. The nominal diameter of the

27、 taper pin shall be 0,37 d, the calculated values are rounded to the nearest standardized nominal diameter in accordance with ISO 2339. The nominal length of the taper pin shall be (w4 2) nominal diameter to taper pin (see Figure 5), the calculated values are rounded to the nearest standardized nomi

28、nal length in accordance with ISO 2339. Nominal sizes and lengths required are given in Tables 4, 5 and 6. Other details of the taper pins, e.g. end radius, cone tolerance and surface finish, shall be in accordance with ISO 2339. Taper pins shall be either of stainless steel or tin-coated carbon ste

29、el. If tin-coated, this shall be either by a hot-dip process or electroplating in accordance with ISO 2093:1986, 7.1, service condition 4. 5 Tolerances 5.1 Nominal diameter of common stud links The allowable manufacturing tolerances on the nominal diameter d of the common stud links, measured at the

30、 crown, are 01mmfor d u 40 mm; 02mmfor 40 mm 122 mm. The cross-sectional area at the crown of the link shall be not less than the area of a circle of the nominal diameter. The allowable manufacturing tolerance on the nominal diameter measured elsewhere on the link is 50%.+The tolerance on the stud-l

31、ink welded parts is +15 %. The allowable manufacturing tolerance of the link except for the requirements specified above is 2,5 %, taking into account the fact that all components of the anchor chain shall fit in with each other. 5.2 Length of five links The length of five links is defined as 5 p +

32、2 d = 22 d. The measurement is taken from the outside. The allowable manufacturing tolerance on a length of five links is 2,50%.+5.3 All other dimensions The tolerances of the diameter: 5%0+The tolerances other than diameter: 2,5 %. BS ISO 1704:20084 6 Range of sizes of links and shackles The range

33、of nominal diameter, d, is that specified by the classification societies associated in the International Association of Classification Societies (IACS). 7 Designation of size The nominal size of a common stud link is designated its nominal diameter, d. The nominal size of other links, shackles and

34、swivels is designated by the nominal diameter, d, of the common stud link. The nominal size of a stud-link anchor chain is designated by the nominal diameter of the common stud link. 8 Connections Examples in the use of connecting chain-shots with joining shackle are shown in Figure 8. Examples in t

35、he use of connecting chain outboard shot to anchor is shown in Figure 9. Key d = nominal diameter of common stud link l = 6 d p = 4 d w = 3,6 d NOTE For nominal dimensions, see Table 1. Figure 1 Common stud link BS ISO 1704:20085Table 1 Nominal dimensions of common stud link Dimensions in millimetre

36、sNominal size d l p w 12,5 75 50 45 14 84 56 50 16 96 64 58 17,5 105 70 63 19 114 76 68 20,5 123 82 74 22 132 88 79 24 144 96 86 26 156 104 94 28 168 112 101 30 180 120 108 32 192 128 115 34 204 136 122 36 216 144 130 38 228 152 137 40 240 160 144 42 252 168 151 44 264 176 158 46 276 184 166 48 288

37、192 173 50 300 200 180 52 312 208 187 54 324 216 194 56 336 224 202 58 348 232 209 60 360 240 216 62 372 248 223 64 384 256 230 66 396 264 238 68 408 272 245 Nominal sized l p w 70 420 280 252 73 438 292 263 76 456 304 274 78 468 312 281 81 486 324 292 84 504 336 302 87 522 348 313 90 540 360 324 92

38、 552 368 331 95 570 380 342 97 582 388 349 100 600 400 360 102 612 408 367 105 630 420 378 107 642 428 385 111 666 444 400 114 684 456 410 117 702 468 421 120 720 480 432 122 732 488 439 124 744 496 446 127 762 508 457 130 780 520 468 132 792 528 475 137 822 548 493 142 852 568 511 147 882 588 529 1

39、52 912 608 547 157 942 628 565 162 972 648 583 BS ISO 1704:20086 Key d = nominal diameter of common stud link d1= nominal diameter of enlarged stud link = 1,1 d l1= 6 d1 6,6 d p1= 4 d1 4,4 d w1= 3,6 d1 3,96 d NOTE For nominal dimensions, see Table 2. Figure 2 Enlarged stud link BS ISO 1704:20087Tabl

40、e 2 Nominal dimensions of enlarged stud link Dimensions in millimetres Nominal size (d, common stud link) d1l1p1w112,5 14 84 56 50 14 16 96 64 58 16 17.5 105 70 63 17,5 19 114 76 68 19 20.5 123 82 74 20,5 22 132 88 79 22 24 144 96 86 24 26 156 104 94 26 28 168 112 101 28 30 180 120 108 30 34 204 136

41、 122 32 36 216 144 130 34 38 228 152 137 36 40 240 160 144 38 42 252 168 151 40 44 264 176 158 42 46 276 184 166 44 48 288 192 173 46 50 300 200 180 48 54 324 216 194 50 56 336 224 202 52 58 348 232 209 54 60 360 240 216 56 62 372 248 223 58 64 384 256 230 60 66 396 264 238 62 68 408 272 245 64 70 4

42、20 280 252 66 73 438 292 263 68 76 456 304 274 Nominal size(d, common stud link) d1l1p1w170 78 468 312 281 73 81 486 324 292 76 84 504 336 302 78 87 510 340 306 81 90 540 360 324 84 92 552 368 331 87 97 582 388 349 90 100 600 400 360 92 102 612 408 367 95 105 630 420 378 97 107 642 428 385 100 111 6

43、66 444 400 102 111 672 448 403 105 114 684 456 410 107 117 702 468 421 111 122 732 488 439 114 124 744 496 446 117 130 780 520 468 120 132 792 528 475 122 137 822 548 493 124 137 822 548 493 127 142 852 568 511 130 142 852 568 511 132 147 882 588 529 137 152 912 608 547 142 157 942 628 565 147 162 9

44、72 648 583 152 167 1 002 668 601 157 173 1 038 692 623 162 178 1 068 712 641 BS ISO 1704:20088 Key d = nominal diameter of common stud link d2= nominal diameter of end link = 1,2 d (d2= 1,2 d) l2= p2+ 2 d2= 6,75 d p2= 3,65 d2 4,35 d w2= 3,3 d2 4 d NOTE For nominal dimensions, see Table 3. Figure 3 E

45、nd link BS ISO 1704:20089Table 3 Nominal dimensions of end link Dimensions in millimetres Nominal size (d, common stud link) d2l2p2w212,5 15 84 54 50 14 17 95 61 56 16 19 108 70 64 17,5 21 117 76 70 19 23 128 83 76 20,5 25 138 89 82 22 26 149 96 88 24 29 162 104 96 26 31 176 113 104 28 34 189 122 11

46、2 30 36 203 131 120 32 38 216 139 128 34 41 230 148 136 36 43 243 157 144 38 46 257 165 152 40 48 270 174 160 42 50 284 183 168 44 53 297 191 176 46 55 311 200 184 48 58 324 209 192 50 60 338 218 200 52 62 351 226 208 54 65 365 235 216 56 67 378 244 224 58 70 392 252 232 60 72 405 261 240 62 74 419

47、270 248 64 77 432 278 256 66 79 446 287 264 68 82 459 296 272 Nominal size(d, common stud link) d2l2p2w270 84 473 305 280 73 88 493 318 292 76 91 513 331 304 78 94 527 339 312 81 97 547 352 324 84 101 567 365 336 87 104 587 378 348 90 108 608 392 360 92 110 621 400 368 95 114 641 413 380 97 116 655

48、422 388 100 120 675 435 400 102 122 689 444 408 105 126 709 457 420 107 128 722 465 428 111 133 749 483 444 114 137 770 496 456 117 140 790 509 468 120 144 810 522 480 122 146 824 531 488 124 149 837 539 496 127 152 857 552 508 130 156 878 566 520 132 158 891 574 528 137 164 925 596 548 142 170 959

49、618 568 147 176 992 639 588 152 182 1 026 661 608 157 188 1 060 683 628 162 194 1 094 705 648 BS ISO 1704:200810 Key 1 retaining pin 2 dovetail chamber d = nominal diameter of common stud link d3= nominal diameter of joining shackle1,3 d l3= 7,1d p3= l3 (d3+ a1+ e1) = 3,4 d w3= 4 d a1= 0,8 d e1= 1,6 d f1= 2,8 d g1= 0,2 d g2= 0,1 d h1= nominal diameter of taper pin h2= nominal length of taper pin R1= 0,6 d R2= 0,5 d NOTE 1 For nominal dimensions, see Table 4. NOTE 2 For taper of retaining pin, see 4.2.5. Figure 4 “D” type