BS ISO 16121-2-2011 Road vehicles Ergonomic requirements for the driver-s workplace in line-service buses Visibility《道路车辆 对专线公共汽车驾驶员工作地点的人类工效学要求 能见度》.pdf

《BS ISO 16121-2-2011 Road vehicles Ergonomic requirements for the driver-s workplace in line-service buses Visibility《道路车辆 对专线公共汽车驾驶员工作地点的人类工效学要求 能见度》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 16121-2-2011 Road vehicles Ergonomic requirements for the driver-s workplace in line-service buses Visibility《道路车辆 对专线公共汽车驾驶员工作地点的人类工效学要求 能见度》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 16121-2:2011Road vehicles Ergonomicrequirements for the driversworkplace in line-service busesPart 2: VisibilityBS ISO 16121-2:2011 BRITISH STANDARDNational forewordThis B

2、ritish Standard is the UK implementation of ISO 16121-2:2011.It supersedes BS ISO 16121-2:2005 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AUE/12, Safety related to occupants.A list of organizations represented on this committee can beobtained on re

3、quest to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 71330 9ICS 13.180; 43.080.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This Bri

4、tish Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate Text affectedBS ISO 16121-2:2011Reference numberISO 16121-2:2011(E)ISO 2011INTERNATIONAL STANDARD ISO16121-2Second edition2011-08-01Road vehicles Er

5、gonomic requirements for the drivers workplace in line-service buses Part 2: Visibility Vhicules routiers Exigences ergonomiques du poste de conduite dans les bus de ville Partie 2: Visibilit BS ISO 16121-2:2011ISO 16121-2:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless oth

6、erwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyrig

7、ht office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 16121-2:2011ISO 16121-2:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction.v 1 S

8、cope1 2 Normative references1 3 Terms and definitions .1 4 Visibility2 4.1 Forward blind spot 2 4.2 Lateral visibility .2 4.3 View upwards.2 4.4 View to passenger compartment .2 4.5 Reflections .3 Bibliography6 BS ISO 16121-2:2011ISO 16121-2:2011(E) iv ISO 2011 All rights reservedForeword ISO (the I

9、nternational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee

10、has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnica

11、l standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bod

12、ies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any

13、 or all such patent rights. ISO 16121-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 13, Ergonomics applicable to road vehicles. This second edition cancels and replaces the first edition (ISO 16121-2:2005), which has been editorially revised. ISO 16121 consists of t

14、he following parts, under the general title Road vehicles Ergonomic requirements for the drivers workplace in line-service buses: Part 1: General description, basic requirements Part 2: Visibility Part 3: Information devices and controls Part 4: Cabin environment BS ISO 16121-2:2011ISO 16121-2:2011(

15、E) ISO 2011 All rights reserved vIntroduction Poor ergonomics in the drivers workplace in buses designed to provide scheduled urban and interurban services increase the already high physical and mental strains on the driver. It is the aim of this part of ISO 16121 to supply the designer of line-serv

16、ice buses with information about how to develop an overall ergonomic concept for the drivers workplace. The recommended requirements on the drivers workplace for line-service buses made in this part of ISO 16121 are based on the scientific conclusions of the research project “drivers workplace in th

17、e line-service bus”. This was conducted in Germany and summarized in the VDV 2341 recommendation. Further comprehensive ergonomic studies related to the design of an enhanced driver workplace conducted in the United States, Canada, the Netherlands, Sweden and the United Kingdom 23456have been consid

18、ered and found to provide recommendations covering similar areas. This part of ISO 16121 sets out to consider the practical implications for all ranges of drivers but particularly those with statures from 1,55 m (small female) to 2,0 m (large male). These statures include shoes (30 mm). It is also e

19、ssential that the designer refers to the specifications and requirements of all parts of ISO 16121 (1 to 4) before completing the design of a drivers workplace. It should be noted that where there is also national legislation covering any of the subjects contained herein, then both should be complie

20、d with. However, if a contradiction between the two should arise in any specific area, then the legislation shall prevail for that specific point only. BS ISO 16121-2:2011BS ISO 16121-2:2011INTERNATIONAL STANDARD ISO 16121-2:2011(E) ISO 2011 All rights reserved 1Road vehicles Ergonomic requirements

21、for the drivers workplace in line-service buses Part 2: Visibility 1 Scope This part of ISO 16121 specifies the requirements for the drivers field of view to the area in front of the vehicle, to the entrance opposite the drivers seat and the interior compartment. It applies to the drivers workplace

22、in low-floor line-service buses designed for the carriage of passengers, comprising more than eight seats in addition to the drivers seat, and having a maximum weight exceeding five metric tonnes and an overall width exceeding 2,30 m. 2 Normative references The following referenced documents are ind

23、ispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 16121-1, Road vehicles Ergonomic requirements for the drivers workplace in line-service

24、 buses Part 1: General description, basic requirements 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 low-floor vehicle in which at least 35 % of the area available for standing passengers (or of its forward section in the case of an articul

25、ated vehicle) forms a single area without steps, reached through at least one service door by a single step from the ground 3.2 vision point V1 point 635 mm vertically above the H-point (as defined in ISO 16121-1) with the seat in its rearmost highest position within the required seat H-point adjust

26、ment range specified in ISO 16121-1 NOTE The V1 and V2 vision points, as defined in ISO 16121-2, can differ from V1 and V2 vision points defined in national and international regulations. 3.3 vision point V2 point 635 mm vertically above the H-point (as defined in ISO 16121-1) with the seat in its f

27、oremost lowest position within the required seat H-point adjustment range specified in ISO 16121-1 NOTE The V1 and V2 vision points, as defined in ISO 16121-2, can differ from V1 and V2 vision points defined in national and international regulations. BS ISO 16121-2:2011ISO 16121-2:2011(E) 2 ISO 2011

28、 All rights reserved4 Visibility 4.1 Forward blind spot 4.1.1 Requirement In order to reduce the blind spot immediately in front of the vehicle, the following requirement shall be met. A bar, having a length equal to the width of the vehicle, placed in front of the bus at a height of 1 100 mm above

29、the ground and 300 mm in front of the foremost surface (normally front face of the bumpers) shall be visible, either by direct or indirect view, from both positions V1 and V2 for a minimum of 95 % of its length (see Figure 1). When checking the requirement of this subclause, any obstruction caused b

30、y the steering wheel shall not be taken into account. If the above requirement cannot be met by direct vision either from V1 or V2, then an alternative device shall be provided to achieve this, such as a mirror or video system. 4.2 Lateral visibility 4.2.1 Requirement If there is a service door loca

31、ted at the front corner of the vehicle, a cube measuring 100 100 100 mm, positioned adjacent to the door at a height of 800 mm above the ground, shall be visible either directly or indirectly. 4.2.2 Testing procedure 4.2.2.1 Position the cube indicated in 4.2.1 alongside the foremost window in the s

32、ervice door at the front corner, with its lowest side positioned horizontally and at a height of 800 mm above the ground (see Figure 2). 4.2.2.2 Check that at least three-fourths of one face of the cube positioned as indicated in 4.2.2.1 is visible from the points V1 and V2 (according to 4.1.1). 4.2

33、.2.3 If the vehicle is fitted with an adjustable dashboard, the requirements of 4.1 and 4.2 shall be checked with the dashboard in its mid-position, as defined by the manufacturer. 4.3 View upwards To ensure sufficient view of traffic lights, etc., a minimum clear angle of view above V1 shall be pro

34、vided. There shall be unobstructed view through the windscreen, measured through a horizontal plane intersecting in V1 with a 15 inclined plane (see Figure 3). When checking this requirement, any obstruction caused by rear view mirror, windscreen wiper arms, split windscreen centre bar, video screen

35、s, sun blind or visor, drivers fan and any legally required marking shall not be taken into account. 4.4 View to passenger compartment Mirrors or other devices shall be provided for the observation of the following passenger compartment areas. Areas to be observed shall be: gangways; and entrance/ex

36、it zones, except within the drivers direct line of sight. BS ISO 16121-2:2011ISO 16121-2:2011(E) ISO 2011 All rights reserved 34.5 Reflections Reflections due to light sources or other illuminated objects, and reflections by sunlight, shall affect or impede as little as possible the view of the outs

37、ide or the information devices and controls. Reflections in the windscreen originating from interior light sources shall be minimized. Reflections in the windscreen which are liable to interfere with judgement of the traffic situation shall be avoided. Dimensions in millimetres Key 1 service door 2

38、required seat H-point adjustment range, as specified in ISO 16121-1 3 alternative device, e.g. mirror, video system, etc. 4 bar, as defined in 4.1.1 Figure 1 Forward blind spot BS ISO 16121-2:2011ISO 16121-2:2011(E) 4 ISO 2011 All rights reservedDimensions in millimetres Key 1 service door 2 require

39、d seat H-point adjustment range 3 cube as defined in 4.2.1 Figure 2 Lateral visibility BS ISO 16121-2:2011ISO 16121-2:2011(E) ISO 2011 All rights reserved 5Dimensions in millimetres Key 1 service door 2 required seat H-point adjustment range Figure 3 View upwards BS ISO 16121-2:2011ISO 16121-2:2011(

40、E) 6 ISO 2011 All rights reservedBibliography 1 VDV 234, Drivers work place in the low-floor line-service bus, Verband Deutscher Verkehrsbetriebe (VDV), Cologne, Germany 2 TCRP Report 25, Bus operator workstation evaluation and design guidelines Summary, sponsored by the Federal Transit Administrati

41、on, USA, 1997 3 STRP Report # 6, Ergonomic study of the drivers workstation in urban buses, Canadian Urban Transit Association 4 NEN 5526, Nederlandse Norm, Ergonomische criteria voor het ontwerpen de beoordeling van de buscabine, Delft 1999 5 Swedish Road and Transport Research Institute, Drivers C

42、ab in Buses, Phase 3: Field tests Summary 6 Bus Cab Ergonomics: Assessment of general layout and guidelines, by ICE Ergonomics Ltd and Sammie CAD Ltd, UK, August 2000 BS ISO 16121-2:2011BS ISO 16121-2:2011ISO 16121-2:2011(E) ICS 13.180; 43.080.20 Price based on 6 pages ISO 2011 All rights reserved T

43、his page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.Briti

44、sh Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or edi

45、tions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the i

46、nside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF

47、 and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for

48、international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.T

49、el: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and