BS ISO 13202-2003 Cranes - Measurement of velocity and time parameters《起重机 速度和时间参数的测量》.pdf

《BS ISO 13202-2003 Cranes - Measurement of velocity and time parameters《起重机 速度和时间参数的测量》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 13202-2003 Cranes - Measurement of velocity and time parameters《起重机 速度和时间参数的测量》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 13202:2003 Cranes Measurement of velocity and time parameters ICS 53.020.20 BS ISO 13202:2003 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 18 September 2003 BSI 18 September 2003 ISBN 0 580 42640 8 National foreword

2、 This British Standard reproduces verbatim ISO 13202:2003 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee MHE/3, Cranes and derricks, to Subcommittee MHE/3/11, Crane safety and testing, which has the responsibility to: A lis

3、t of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Corres

4、pondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not o

5、f itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments

6、 and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendment

7、s issued since publication Amd. No. Date Comments Reference number ISO 13202:2003(E) OSI 3002INTERNATIONAL ADNATSDR ISO 12023 tide tsriFino 3002-0910- Cranes Measurement of velocity and time parameters Appareils de levage charge suspendue Mesurage des paramtres de vitesse et de temps Referecne unbme

8、r OSI 20231:002)E(3 ISO 2003INTERNATIONAL STANDARD ISO 13202 First edition 2003-09-01 senarC saeMemerunt fo veloticy nad marap emiterets ppAareils ed vela eg crahs eguspeudn e seMurage sed paramrtse de ivteess et ed temps BSISO13202:2003IS:20231 O3002(E) ii BSISO13202:2003IS:20231 O3002(E) iiiForewo

9、rd ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technic

10、al committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of el

11、ectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to t

12、he member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for id

13、entifying any or all such patent rights. ISO 13202 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 4, Test methods. BSISO13202:2003blankINTENRATIONAL TSANDADR IS:20231 O3002(E)1Cranes Measurement of velocity and time parameters 1 Scope This International Standard establishes g

14、uidelines for the measurement of the velocity and time parameters of cranes as defined in ISO 7363. This International Standard is complementary to ISO 4310 and covers the types of crane specified therein. 2 Normative references The following referenced documents are indispensable for the applicatio

15、n of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4310, Cranes Test code and procedures ISO 7363, Cranes and lifting appliances Technical characteristics and acceptan

16、ce documents ISO 9373, Cranes and related equipment Accuracy requirements for measuring parameters during testing 3 Test conditions Test conditions shall meet the requirements of ISO 4310. Before conducting the test, crane systems and mechanisms shall be checked for proper functioning while running

17、without load. A crane presented for testing shall be equipped in accordance with the manufacturers specification and shall comply with ISO 7363. 4 Measuring apparatus and their accuracy Measuring apparatus used in crane tests to determine motion velocity and time parameters shall be selected in acco

18、rdance with the accuracy required in ISO 9373 and in compliance with national specifications. The number of measurements and the allowable tolerance on the values of motion velocity and time parameters measured during testing shall meet the requirements of ISO 9373. 5 Test procedure Before taking me

19、asurements of velocity and time parameters, trial cycles should be carried out to ensure that the elements (components) of the crane perform in the manner required for the test. BSISO13202:2003IS:20231 O3002(E) 2 Measurements of maximum, minimum and specified intermediate motion velocities (or their

20、 corresponding time parameters) of other elements (components) of the crane shall be taken, as appropriate, in the loaded and unloaded conditions. The linear motion velocity of the elements (components) or crane shall be determined by calculation from measurements of the time required to traverse th

21、e measured test path length. The acceleration and deceleration parts of the motion shall be excluded. The measurement results shall be recorded. The angular motion velocity of the elements (components) or crane shall be determined by calculation from the measurements of the time required to move alo

22、ng the test arc. The acceleration and deceleration parts of the motion shall be excluded. The measurement results shall be recorded. Table A.1 shows a format example for calculation of the average linear motion velocity. Table A.2 shows a format example for calculation of the average angular motion

23、velocity. These values may also be determined in other appropriate formats. 6 Test report The test report on the measurement of motion velocity and time parameters shall include the following data: a) crane designation and type; b) crane identification or serial number; c) manufacturer; d) date of t

24、he measurement; e) description of the crane and equipment; f) description of the measuring apparatus and method; g) test conditions; h) location and state of test ground, road, track, as appropriate; i) crane configuration during each test; j) results of measurements of maximum load capacity (tabula

25、ted); k) name of the person supervising the testing. BSISO13202:2003IS:20231 O3002(E) 3Annex A (informative) Format examples for representation of measurement results of velocity and time parameters Table A.1 Measurements of linear velocities and time intervals for the elements (components) of the c

26、rane and the crane as a whole No. of measurement Direction of movement Time measurement interval Path length measured Motion velocity t l l v t = s m m/s 1 t 1l 1v 12 t 2l 2v 23 t 3l 3v 3. . n t nl nv nAverage motion velocity: v a= (v 1+ v 2+ v 3+ + v n )/n. Table A.2 Measurements of angular velocit

27、ies and time intervals for the elements (components) of the crane and the crane as a whole No. of measurement Direction of movement Time measurement interval Arc of path measured Angular velocity t t = s rad rad/s 1 t 1 1 12 t 2 2 23 t 3 3 3. . n t n n nAverage angular velocity: a= ( 1+ 2+ 3+ + n )/

28、n. BSISO13202:2003BS ISO 13202:2003 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal

29、Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an ina

30、ccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS wh

31、ich ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are al

32、so available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informat

33、ion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +4

34、4 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 899

35、6 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds th

36、e copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or

37、otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.