BS ISO 128-30-2001 Technical drawings - General principles of presentation - Basic conventions for views《技术制图 表示的一般原则 基本惯例》.pdf

《BS ISO 128-30-2001 Technical drawings - General principles of presentation - Basic conventions for views《技术制图 表示的一般原则 基本惯例》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 128-30-2001 Technical drawings - General principles of presentation - Basic conventions for views《技术制图 表示的一般原则 基本惯例》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 128-30:2001 Technical drawings General principles of presentation Part 30: Basic conventions for views ICS 01.100.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 128-30:2001 This British Standard, having been prepared under the direction of the

2、 Consumer Products and Services Sector committee, was published under the authority of the Standards Committee and comes into effect on 15 July 2001 BSI 07-2001 ISBN 0 580 37717 2 National foreword This British Standard reproduces verbatim ISO 128-30:2001 and implements it as the UK national standar

3、d. It partially supersedes BS ISO 128:1982 which will be withdrawn on completion of the overall revision process for ISO 128:1982. The UK participation in its preparation was entrusted to Technical Committee TDW/4, Engineering drawing, Metrology, precision measurement and all related documentation,

4、which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the sec

5、tion entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application

6、. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor

7、related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages i to iv, pages 1 to 11 and a back cover. The BSI copyright date displayed in this document indicates when the docume

8、nt was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STANDARD ISO 128-30 First edition 2001-04-01 Reference number ISO 128-30:2001(E) Technical drawings General principles of presentation Part 30: Basic conventions for views Dessins techniques Principes gnraux

9、de reprsentation Partie 30: Conventions de base pour les vuesISO 128-30:2001(E) iiISO 128-30:2001(E) iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is norm

10、ally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in t

11、he work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the techni

12、cal committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 128 may be the subject of patent rights.

13、 ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 128-30 was prepared by Technical Committee ISO/TC 10, Technical product documentation, Subcommittee SC 1, Basic conventions. This first edition is based on ISO 128:1982, clause 2 of which it

14、cancels and replaces. ISO 128 consists of the following parts, under the general title Technical drawings General principles of presentation: Part 20: Basic conventions for lines Part 21: Preparation of lines by CAD systems Part 22: Basic conventions and applications for leader lines and reference l

15、ines Part 23: Lines on construction drawings Part 24: Lines on mechanical engineering drawings Part 25: Lines on shipbuilding drawings Part 30: Basic conventions for views Part 34: Views on mechanical engineering drawings Part 40: Basic conventions for cuts and sections Part 44: Sections on mechanic

16、al engineering drawings Part 50: Basic conventions for representing areas on cuts and sections The following part is under preparation: Part 1: Introduction and index. Annexes A ,B and C form a normative part of this part of ISO 128.ISO 128-30:2001(E) iv Introduction According to the replaced clause

17、 2 of ISO 128:1982 three different methods of presenting views are allowed. In this part of ISO 128, the method of using reference arrows has been selected as the preferred one. The first angle projection method (formerly referred to as method E) and the third angle projection method (formerly refer

18、red to as method A) are still to be regarded as normative. Annexes A and B of this part of ISO 128 give basic information on the first and third angle projection methods; ISO 5456-2 specifies the rules in detail.INTERNATIONAL STANDARD ISO 128-30:2001(E) 1 Technical drawings General principles of pre

19、sentation Part 30: Basic conventions for views 1 Scope This part of ISO 128 specifies the general principles for presenting views, applicable to all kinds of technical drawings (mechanical, electrical, architectural, civil engineering, etc.), following the orthographic projection methods specified i

20、n ISO 5456-2. Attention has also been given in this part of ISO 128 to the requirements of reproduction, including microcopying in accordance with ISO 6428. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of thi

21、s part of ISO 128. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 128 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indic

22、ated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 128-24:1999, Technical drawings General principles of presentation Part 24: Lines on mechanical engineering

23、drawings. ISO 3098-0, Technical product documentation Lettering Part 0: General requirements. ISO 5456-2, Technical drawings Projection methods Part 2: Orthographic representations. ISO 6428, Technical drawings Requirements for microcopying. ISO 10209-1, Technical product documentation Vocabulary Pa

24、rt 1: Terms relating to technical drawings: general and types of drawings. ISO 10209-2, Technical product documentation Vocabulary Part 2: Terms relating to projection methods. ISO 81714-1, Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules. 3 Terms an

25、d definitions For the purposes of this part of ISO 128, the terms and definitions given in ISO 10209-1 and ISO 10209-2 apply. 4 General The most informative view of an object shall be used as the front or principal figure, taking into consideration, for example, its functioning position, position of

26、 manufacturing or mounting. Each view, with the exception of the front or principal figure (view, plan, principal figure), shall be given clear identification with a capital letter, repeated near the reference arrow needed to indicate the direction of viewing for theISO 128-30:2001(E) 2 relevant vie

27、w. Whatever the direction of viewing, the capital letter shall always be positioned in normal relation to the direction of reading, and be indicated either above or on the right side of the reference arrow. The reference arrow is defined in annex C (including the arc arrow, see clause 7), as is the

28、lettering height of the identification. The designated views may be located irrespective of the principal figure. The capital letters identifying the referenced views shall be placed immediately above the relevant views (see Figure 1). 5 Choice of views When views (including cuts and sections) are n

29、eeded, these shall be selected according to the following principles: limit the number of views (and cuts and sections) to the minimum necessary but sufficient to fully delineate the object without ambiguity; avoid the need for hidden outlines and edges; avoid unnecessary repetition of a detail. Fig

30、ure 1 Identification of referenced viewsISO 128-30:2001(E) 3 6 Partial views 6.1 General Features needing specific illustration, but not meriting a full view, may be illustrated using a partial view limited by a continuous narrow line with zigzags of type 01.1.19 according to ISO 128-24:1999 (see Fi

31、gure 2). 6.2 Partial view of symmetrical parts To save time and space, symmetrical objects may be drawn as a fraction of the whole see Figure 3 a), b) and c). The line of symmetry is identified at each of its ends by two narrow short parallel lines drawn at right angles to it see Figure 3 a), b) and

32、 c). The graphical symbol for symmetry shall be drawn in accordance with clause C.4. 7 Special positions of view When necessary, it is permitted to show the view in another position than that indicated by the reference arrow. Figure 2 Partial view a) Example 1 b) Example 2 c) Example 3 Figure 3 Part

33、ial view of symmetrical partsISO 128-30:2001(E) 4 The fact that the view is shown in another position should be clarified by an arc arrow showing the direction of rotation according to Figure 4 a) and b). The angle of rotation of the view after the capital letter may be indicated. If used, the seque

34、nce shall be: “view identification arc arrow angle of rotation” The arc arrow shall be drawn in accordance with clause C.3. a) Example 1 b) Example 2 Figure 4 Special view positionsISO 128-30:2001(E) 5 Annex A (normative) First angle projection method A.1 General The first angle projection method is

35、 to be regarded as a requirement of this part of ISO 128. A more detailed description of the first angle projection method is to be found in ISO 5456-2. A.2 First angle projection method With reference to the front view, (a), the other views are arranged as follows (see Figure A.1): the view from ab

36、ove, (b), is placed underneath; the view from below, (e), is placed above; the view from the left, (c), is placed on the right; the view from the right, (d), is placed on the left; the view from the rear, (f), may be placed on the left or right, as convenient. Figure A.1 First angle projection metho

37、dISO 128-30:2001(E) 6 A.3 Graphical symbol The graphical symbol for the first angle projection method is shown in Figure A.2. The proportions and dimensions of this graphical symbol are specified in ISO 5456-2. Figure A.2 Graphical symbolISO 128-30:2001(E) 7 Annex B (normative) Third angle projectio

38、n method B.1 General The third angle projection method is to be regarded as a requirement of this part of ISO 128. A more detailed description of the third angle projection method is to be found in ISO 5456-2. B.2 Third angle projecion method With reference to the front view, (a), the other views ar

39、e arranged as follows (see Figure B.1): the view from above, (b), is placed above; the view from below, (e), is placed underneath; the view from the left, (c), is placed on the left; the view from the right, (d), is placed on the right; the view from the rear, (f), may be placed on the left or right

40、, as convenient. Figure B.1 Third angle projection methodISO 128-30:2001(E) 8 B.3 Graphical symbol The graphical symbol for the third angle projection method is shown in Figure B.2. The proportions and dimensions of this graphical symbol are specified in ISO 5456-2. Figure B.2 Graphical symbolISO 12

41、8-30:2001(E) 9 Annex C (normative) Graphical symbols C.1 General In order to harmonize the sizes of the graphical symbols specified in this part of ISO 128 with those of the other inscriptions on the drawing (dimensions, tolerances, etc.), the rules given in ISO 81714-1 shall apply. The view identif

42、ication lettering height, , shall be larger than the normal lettering on the technical drawing by a factor of Within Figures C.1, C.2 and C.3, lettering type B, vertical, according to ISO 3098-0, applies. Other lettering types are also permitted. C.2 Reference arrow Se eF i g ur eC . 1 . C.3 Arc arr

43、ow Se eF i g ur eC . 2 . Figure C.1 Graphical symbol for reference arrows Figure C.2 Graphical symbol for arc arrows h p 2.ISO 128-30:2001(E) 10 C.4 Symmetry S eeFig u reC .3 . Figure C.3 Graphical symbol for symmetryISO 128-30:2001(E) 11 Bibliography 1 ISO 128-20, Technical drawings General princip

44、les of presentation Part 20: Basic conventions for lines.BS ISO 128-30:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internati

45、onal level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We wo

46、uld be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual upd

47、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also

48、available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information

49、 on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For