BS ISO 10228-2011 Cross-country skis Binding mounting area Requirements for test screws《越野滑雪 捆扎部位 试验螺钉的要求》.pdf

《BS ISO 10228-2011 Cross-country skis Binding mounting area Requirements for test screws《越野滑雪 捆扎部位 试验螺钉的要求》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 10228-2011 Cross-country skis Binding mounting area Requirements for test screws《越野滑雪 捆扎部位 试验螺钉的要求》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 10228:2011Cross-country skis Binding mounting area Requirements for test screwsBS ISO 10228:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implement

2、ation of ISO 10228:2011. It supersedes BS ISO 10228:1991, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e S W / 1 3 6 / 7 , S n o w s p o r t s e q u i p m e n t .A list of organizations represented on this committee can be obtained on

3、request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 70614 1 ICS 97.220.20 Compliance with a British Standard cannot confer immunity from legal obligations.This Bri

4、tish Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 10228:2011Reference numberISO 10228:2011(E)ISO 2011INTERNATIONAL STANDARD ISO10228Second edition2011-05-15Cross-country

5、skis Binding mounting area Requirements for test screws Skis de fond Zone de montage de la fixation Exigences pour les vis dessai BS ISO 10228:2011ISO 10228:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or

6、 utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11

7、 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS ISO 10228:2011ISO 10228:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards

8、bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizat

9、ions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in th

10、e ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of

11、the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and

12、 recreational equipment, Subcommittee SC 4, Snowsports equipment. This second edition cancels and replaces the first edition (ISO 10228:1991), which has been technically revised. BS ISO 10228:2011ISO 10228:2011(E) iv ISO 2011 All rights reservedIntroduction The use of test screws ensures the compara

13、bility of measurement data, which are determined by the manufacturer or other institutions by testing the binding mounting area of cross-country skis. BS ISO 10228:2011INTERNATIONAL STANDARD ISO 10228:2011(E) ISO 2011 All rights reserved 1Cross-country skis Binding mounting area Requirements for tes

14、t screws 1 Scope This International Standard specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis. 2 Normative references The following referenced documents are indispensable for the application

15、of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1478, Tapping screws thread ISO 2702, Heat-treated steel tapping screws Mechanical properties ISO 7794, Cross-country

16、skis Ski-binding screws Requirements ISO 7795, Cross-country skis Ski-binding screws Test methods 3 Terms and definitions For the purposes of this document, the definitions given in ISO 7794 and the following apply. 3.1 test screw fastener, which is used for testing the binding mounting area to ensu

17、re the comparability of measurement data 4 Designation Test screws in accordance with this International Standard shall be designated by: a) the words “Test screw”; b) the reference to this International Standard, i.e. ISO 10228; c) their nominal dimensions, i.e. diameter length. EXAMPLE Test screws

18、 with a nominal diameter of 6,3 mm and a length of 18 mm would be designated: Test screw ISO 10228 6,3 18 BS ISO 10228:2011ISO 10228:2011(E) 2 ISO 2011 All rights reserved5 Requirements 5.1 General The strength requirements and typical application characteristics of cross-country ski-binding test sc

19、rews shall be tested in accordance with ISO 7795. 5.2 Materials Test screws shall be made of steel as specified in ISO 2702, which shall comply with the additional requirements in 5.4 and 5.5 of this International Standard. 5.3 Dimensions 5.3.1 Screw head Test screws shall be cross recess type Z No.

20、 3 with a recommended minimum penetration depth of 2,72 mm to 3,18 mm (see ISO 4757). If screws having countersunk heads are used, the angle of countersinking 2090+ is recommended. 5.3.2 Thread and end configuration The cross-section of the test screw may be circular or non-circular within the major

21、 diameter of 00,156,3 mm mm(see Figure 1). The thread length shall be at least 1 mm longer than the penetration depth, irrespective of the shaft length. The tolerance on the length of the screw shall be 0,6 mm. The shaft end shall correspond to Figure 1. 5.4 Surface Test screws shall be coated or pl

22、ated with materials which provide adequate protection against corrosion and ensure a reproducible coefficient of friction. For example, a suitable coating would be a zinc electroplated coating, Fe/Zn 5c (see ISO 4042), having a clear chromate conversion coating and a minimum local thickness of 5 m (

23、batch average 4 min., 6 m max.), when measured on the top surface of the screw head. During electroplating, adequate precautions shall be taken to avoid hydrogen embrittlement. 5.5 Application characteristics 5.5.1 General The specified fastening and mounting characteristics of the test screw shall

24、be based on a uniform drill diameter of 0,1503,6 mm mm.+5.5.2 Strength requirements The breaking moment for test screws under a torque of the same axis and direction as the driving torque shall be not less than 10 Nm. The screws shall not break when subjected to the conditions of the ductility test.

25、 BS ISO 10228:2011ISO 10228:2011(E) ISO 2011 All rights reserved 35.5.3 Fastening characteristics The mean static pull-out resistance shall correspond to at least that of a reference screw complying with the requirements of ISO 1478, type F, and having a nominal diameter of 6,3 mm. Dimensions in mil

26、limetres aCross-recess type Z No. 3 in accordance with ISO 4757. bPitch. Figure 1 Head, thread and end configuration BS ISO 10228:2011ISO 10228:2011(E) 4 ISO 2011 All rights reservedBibliography 1 ISO 4042, Fasteners Electroplated coatings 2 ISO 4757, Cross recesses for screws BS ISO 10228:2011BS IS

27、O 10228:2011ISO 10228:2011(E) ICS 97.220.20 Price based on 4 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view

28、 on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revi

29、sion. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform t

30、he Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of

31、standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Cus

32、tomer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide ran

33、ge of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44

34、 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Inf

35、ormation regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodi

36、es. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free

37、use, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: