BS EN ISO 12180-1-2011 Geometrical product specifications (GPS) Cylindricity Vocabulary and parameters of cylindrical form《产品几何技术规范(GPS) 圆柱度 圆柱形词汇和参数》.pdf

《BS EN ISO 12180-1-2011 Geometrical product specifications (GPS) Cylindricity Vocabulary and parameters of cylindrical form《产品几何技术规范(GPS) 圆柱度 圆柱形词汇和参数》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 12180-1-2011 Geometrical product specifications (GPS) Cylindricity Vocabulary and parameters of cylindrical form《产品几何技术规范(GPS) 圆柱度 圆柱形词汇和参数》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 12180-1:2011Geometrical product specifications (GPS) CylindricityPart 1: Vocabulary and parameters of cylindrical formBS EN ISO 12180-1:2011 BRITISH STANDARDNational fo

2、rewordThis British Standard is the UK implementation of EN ISO 12180-1:2011. It supersedes DD CEN ISO/TS 12180-1:2007, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization.A list of organizations represented on this comm

3、ittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 66720 6 ICS 01.040.17; 17.040.20 Compliance with a British Standard cannot confer immu

4、nity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 12180-1 April 2011 ICS 01.040.17; 17.040.20

5、Supersedes CEN ISO/TS 12180-1:2007English Version Geometrical product specifications (GPS) - Cylindricity - Part 1: Vocabulary and parameters of cylindrical form (ISO 12180-1:2011) Spcification gomtrique des produits (GPS) - Cylindricit - Partie 1: Vocabulaire et paramtres de cylindricit (ISO 12180-

6、1:2011) Geometrische Produktspezifikation (GPS) - Zylindrizitt - Teil 1: Begriffe und Kenngren der Zylinderform (ISO 12180-1:2011) This European Standard was approved by CEN on 26 February 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions

7、for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in th

8、ree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards b

9、odies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United

10、Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 12180-1:201

11、1: EBS EN ISO 12180-1:2011 EN ISO 12180-1:2011 (E) 3 Foreword This document (EN ISO 12180-1:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrica

12、l product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withd

13、rawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN ISO/TS 12180-1:2007.

14、According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland

15、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 12180-1:2011 has been approved by CEN as a EN ISO 12180-1:2011 without any modification. BS EN ISO

16、12180-1:2011ISO 12180-1:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .1 3.1 General terms 2 3.2 Terms relating to the surface .2 3.3 Terms relating to the reference cylinder.4 3.4 Terms relating to the circu

17、mference and the generatrix.5 3.5 Terms relating to parameters.5 4 Radial cross-section deviations 8 5 Straightness deviations8 Annex A (informative) Mathematical definition of cylindricity tolerances of nominal integral features.9 Annex B (informative) Consideration in the assessment of deviations

18、from cylindrical form.10 Annex C (informative) Synoptic tables of terms, abbreviated terms and parameters.12 Annex D (informative) Relationship to the GPS matrix model .14 Bibliography16 BS EN ISO 12180-1:2011ISO 12180-1:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organiza

19、tion for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established

20、has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. In

21、ternational Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publi

22、cation as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent r

23、ights. ISO 12180-1 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This first edition of ISO 12180-1 cancels and replaces ISO/TS 12180-1:2003, which has been technically revised. ISO 12180 consists of the following parts, under the

24、 general title Geometrical product specifications (GPS) Cylindricity: Part 1: Vocabulary and parameters of cylindrical form Part 2: Specification operators BS EN ISO 12180-1:2011ISO 12180-1:2011(E) ISO 2011 All rights reserved vIntroduction This part of ISO 12180 is a geometrical product specificati

25、on (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences chain link 2 of the chain of standards on form of a surface (independent of a datum). The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this part of ISO 121

26、80 is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this part of ISO 12180 and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this part of ISO 12180, unless otherwise indicated. For more detailed information on the relationship o

27、f this part of ISO 12180 to other standards and the GPS matrix model, see Annex D. This part of ISO 12180 defines terms and concepts necessary for defining the specification operators according to ISO 17450-2 for cylindricity of integral features. Extracting data always involves applying a certain f

28、iltering process. An additional filtering of the extracted data might or might not be applied. This additional filter can be a mean line filter (Gaussian, spline, wavelet, etc.) or a non-linear filter (e.g. morphological filter). The type of filtering influences the definition of cylindricity and th

29、e specification operators and, therefore, needs to be stated unambiguously. This part of ISO 12180 is not intended to disallow any means of measuring cylindricity. BS EN ISO 12180-1:2011BS EN ISO 12180-1:2011INTERNATIONAL STANDARD ISO 12180-1:2011(E) ISO 2011 All rights reserved 1Geometrical product

30、 specifications (GPS) Cylindricity Part 1: Vocabulary and parameters of cylindrical form 1 Scope This part of ISO 12180 defines the terms and concepts related to cylindricity of individual complete integral features only. 2 Normative references The following referenced documents are indispensable fo

31、r the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 11562:1996, Geometrical Product Specifications (GPS) Surface texture: Profile method Metrological ch

32、aracteristics of phase correct filters ISO 12181-1:2011, Geometrical product specifications (GPS) Roundness Part 1: Vocabulary and parameters of roundness ISO 12780-1:2011, Geometrical product specifications (GPS) Straightness Part 1: Vocabulary and parameters of straightness ISO 14660-1:1999, Geome

33、trical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions ISO 14660-2:1999, Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature ISO 1745

34、0-1:1), Geometrical product specifications (GPS) General concepts Part 1: Model for geo-metrical specification and verification 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 11562, ISO 12181-1, ISO 12780-1, ISO 14660-1, ISO 14660-2, ISO 17450-1 and

35、 the following apply. 1) To be published. (Revision of ISO/TS 17450-1:2005) BS EN ISO 12180-1:2011ISO 12180-1:2011(E) 2 ISO 2011 All rights reserved3.1 General terms 3.1.1 cylindricity property of a cylinder 3.1.2 nominal cylinder mathematically cylindrical form as specified by design intent NOTE Fo

36、r the purposes of this part of ISO 12180, the term “form of a nominal cylinder” is understood to mean the form of a right circular cylinder (i.e. it has a right angle between the cylinder axis and every circular cross-section). 3.1.3 generatrix plane half plane through the axis of the associated cyl

37、inder 3.2 Terms relating to the surface 3.2.1 extracted surface cylindricity digital representation of the real surface NOTE The extraction conventions for cylindricity are given in ISO 12180-2. This extracted surface is an extracted integral feature as defined in ISO 14660-1. 3.2.2 cylindricity sur

38、face extracted surface (type cylinder) intentionally modified by a filter NOTE This is the surface to which the concepts and parameters of this part of ISO 12180 can be applied. 3.2.3 local cylindricity deviation Cldeviation of a point on a cylindricity surface from the reference cylinder, the devia

39、tion being normal to the reference cylinder See Figures 1 and 2. NOTE 1 The deviation is negative if from the reference cylinder the point lies in the direction of the material. NOTE 2 For the reference cylinder, see 3.3.1. BS EN ISO 12180-1:2011ISO 12180-1:2011(E) ISO 2011 All rights reserved 3Key

40、1 reference cylinder aPositive local deviation. bNegative local deviation. Figure 1 Local form deviation of an external cylindrical feature Key 1 reference cylinder aNegative local deviation.bPositive local deviation. Figure 2 Local form deviation of an internal cylindrical feature 3.2.4 extracted g

41、eneratrix line digital representation of the line of intersection of the real surface and a generatrix plane NOTE The extraction conventions for cylindricity are given in ISO 12180-2. This extracted surface is an extracted integral feature as defined in ISO 14660-1. 3.2.5 generatrix profile extracte

42、d generatrix line intentionally modified by a filter BS EN ISO 12180-1:2011ISO 12180-1:2011(E) 4 ISO 2011 All rights reserved3.2.6 local generatrix deviation deviation of a point on a generatrix from the reference line, the deviation being normal to the reference line NOTE 1 The deviation is negativ

43、e if from the reference line the point lies in the direction of the material. NOTE 2 This definition is similar to ISO 12780-1:2011, definition 3.2.4: local straightness deviation. 3.3 Terms relating to the reference cylinder 3.3.1 reference cylinder associated cylinder fitting the cylindricity surf

44、ace in accordance with specified conventions, to which the deviations from cylindrical form and the cylindricity parameters are referred 3.3.1.1 minimum zone reference cylinders two coaxial cylinders enclosing the cylindricity surface and having the least radial separation NOTE The abbreviated term

45、MZ is used to refer to minimum zone reference elements. 3.3.1.1.1 outer minimum zone reference cylinder outer cylinder of the minimum zone reference cylinders 3.3.1.1.2 inner minimum zone reference cylinder inner cylinder of the minimum zone reference cylinders 3.3.1.1.3 mean minimum zone reference

46、cylinder arithmetic mean cylinder of the minimum zone reference cylinders 3.3.1.2 least squares reference cylinder cylinder for which the sum of the squares of the local cylindricity deviations is a minimum NOTE The abbreviated term LS is used to refer to least squares reference elements and the abb

47、reviated term G (for Gaussian), is used as a prefix for parameters based on least squares reference elements. 3.3.1.3 minimum circumscribed reference cylinder smallest possible cylinder that can be fitted around the cylindricity surface NOTE The abbreviated term MC is used to refer to minimum circum

48、scribed reference elements. 3.3.1.4 maximum inscribed reference cylinder largest possible cylinder that can be fitted within the cylindricity surface NOTE 1 Cases exist where the maximum inscribed reference cylinder is not unique. NOTE 2 The abbreviated term MI is used to refer to maximum inscribed

49、reference elements. 3.3.2 associated derived axis of a cylindrical feature axis of the reference cylinder(s) BS EN ISO 12180-1:2011ISO 12180-1:2011(E) ISO 2011 All rights reserved 53.4 Terms relating to the circumference and the generatrix 3.4.1 generatrix wavelength length of a generatrix divided by the number of sinusoidal undulations along that generatrix NOTE The number of sinusoidal undulations is not necessarily an integer. 3.5 Terms relating to parameters 3.5.1 General parameters 3.5.1.1 peak