BS EN ISO 1683-2015 Acoustics Preferred reference values for acoustical and vibratory levels《声学 听觉和振动等级用基准参考值》.pdf

《BS EN ISO 1683-2015 Acoustics Preferred reference values for acoustical and vibratory levels《声学 听觉和振动等级用基准参考值》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 1683-2015 Acoustics Preferred reference values for acoustical and vibratory levels《声学 听觉和振动等级用基准参考值》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 1683:2015Acoustics Preferredreference values for acousticaland vibratory levelsBS EN ISO 1683:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 1683:2015. It supersedes BS EN ISO 1683:2008 which is withdrawn.The UK parti

2、cipation in its preparation was entrusted to Technical Committee EH/1, Acoustics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its co

3、rrect application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83922 1ICS 17.140.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Str

4、ategy Committee on 31 May 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1683 May 2015 ICS 17.140.01 Supersedes EN ISO 1683:2008English Version Acoustics - Preferred reference values for acoustical and vibratory

5、 levels (ISO 1683:2015) Acoustique - Valeurs de rfrence recommandes pour les niveaux acoustiques et vibratoires (ISO 1683:2015) Akustik - Bevorzugte Bezugswerte fr Pegel in der Akustik und Schwingungstechnik (ISO 1683:2015) This European Standard was approved by CEN on 30 April 2015. CEN members are

6、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

7、he CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Cen

8、tre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

9、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-10

10、00 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1683:2015 EBS EN ISO 1683:2015Foreword This document (EN ISO 1683:2015) has been prepared by Technical Committee ISO/TC 43 “Acoustics” in collaboration with Techn

11、ical Committee CEN/TC 211 “Acoustics” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2015, and conflicting national standards shall be withdrawn

12、at the latest by November 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1683:2008. According t

13、o the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greec

14、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1683:2015 has been approved by CEN as EN ISO 1683:2015 without

15、any modification. EN ISO 1683:2015 (E)BS EN ISO 1683:2015ISO 1683:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Specifications . 24.1 Reference values for airborne sound quantities 24.2 Reference values for sound quantities in liquids 24.3 Reference

16、values for vibratory quantities . 3Bibliography 4 ISO 2015 All rights reserved iiiContents PageBS EN ISO 1683:2015ISO 1683:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Interna

17、tional Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with

18、ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, P

19、art 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the

20、 elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations re

21、ceived (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs a

22、dherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 43, Acoustics.This third edition cancels and replaces the second edition (ISO 1683:2008), which has been technicall

23、y revised.iv ISO 2015 All rights reservedBS EN ISO 1683:2015ISO 1683:2015(E)IntroductionVarious kinds of acoustical and vibratory levels expressed in decibels are commonly used in acoustics. In order to establish a uniform basis for the expression of those levels, a set of agreed reference values is

24、 needed.The reference value determines whether the level for a particular quantity is positive or negative. For general measurements and many engineering specifications, it is desirable that levels of a given kind be consistently positive (or consistently negative) rather than both positive and nega

25、tive.In general, a reference value is expressed as the number one and a derived SI unit formed by the use of an appropriate SI prefix.The values specified in this International Standard represent the values internationally adopted.For airborne sound, a special reference value for sound pressure is s

26、tated according to widespread use and legal implications. ISO 2015 All rights reserved vBS EN ISO 1683:2015BS EN ISO 1683:2015Acoustics Preferred reference values for acoustical and vibratory levels1 ScopeThis International Standard specifies reference values used in acoustics, in order to establish

27、 a uniform basis for the expression of acoustical and vibratory levels.The reference values are mandatory for use in acoustics for sounds in air and other gases, sounds in water and other liquids, and for structure-borne sound, but can also be used in other applications.2 Normative referencesThe fol

28、lowing documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2041, Mechan

29、ical vibration, shock and condition monitoring VocabularyISO/TR 25417, Acoustics Definitions of basic quantities and termsISO 80000-8, Quantities and units Part 8: Acoustics3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 2041, ISO/TR 25417, ISO 80000-

30、8, and the following apply.3.1reference valuequantity value used as a basis for comparison with values of quantities of the same kindSOURCE: ISO/IEC Guide 99:2007, 5.18Note 1 to entry: For the purposes of this International Standard, a reference value is expressed in terms of a number and an appropr

31、iate unit of measurement used to form a ratio of dimension one when defining a logarithmic quantity.INTERNATIONAL STANDARD ISO 1683:2015(E) ISO 2015 All rights reserved 1BS EN ISO 1683:2015ISO 1683:2015(E)4 Specifications4.1 Reference values for airborne sound quantitiesReference values for various

32、sound quantities in air and other gases are given in Table 1.Table 1 Reference values for sound quantities in air and gasesQuantity Reference valueaSound pressure 20 PaSound exposure (20 Pa)2sSound power 1 pWSound energy 1 pJSound intensity 1 pW/m2aThe reference value used to establish a level for a

33、 certain acoustical quantity should always be stated together with the respective level.4.2 Reference values for sound quantities in liquidsReference values for various sound quantities in water and other liquids are given in Table 2.Table 2 Reference values for sound quantities in water and other l

34、iquidsQuantity Reference valueaSound pressureb1 PaSound exposure 1 Pa2sSound power 1 pWSound energy 1 pJSound intensity 1 pW/m2Sound particle displace-ment1 pmSound particle velocity 1 nm/sSound particle acceleration 1 m/s2Distancec1 maThe reference value used to establish a level for a certain acou

35、stical quantity should always be stated together with the respective level.b A sound pressure level with a reference value of 1 Pa is numerically 10 lg(202/12) dB, which is approximately 26,0 dB greater than the sound pressure level for the same sound pressure but with a reference value of 20 Pa.cTh

36、e reference value for distance is used to form reference values for compound quantities, such as the product of sound pressure and distance (for which the reference value is 1 Pa m) or sound exposure and squared distance (for which the reference value is 1 Pa2m2s). Ratios of these compound quantitie

37、s to other sound quantities lead to further compound quantities with dimensions of distance (with reference value 1 m) or area (with reference value 1 m2).2 ISO 2015 All rights reservedBS EN ISO 1683:2015ISO 1683:2015(E)4.3 Reference values for vibratory quantitiesReference values for various vibrat

38、ory quantities are given in Table 3.Table 3 Reference values for vibratory quantitiesQuantity Reference valueaVibratory displacement 1 pmVibratory velocityb1 nm/sVibratory acceleration 1 m/s2Vibratory force 1 NaThe reference value used to establish a level for a certain vibratory quantity should alw

39、ays be stated together with the respective level.bIn connection with structure-borne sound, a reference value of 50 nm/s is also in use. In this event, the vibratory velocity level takes values close to the associated sound pressure and sound intensity levels. ISO 2015 All rights reserved 3BS EN ISO

40、 1683:2015ISO 1683:2015(E)Bibliography1 ISO/IEC Guide 99:2007, International vocabulary of metrology Basic and general concepts and associated terms (VIM)4 ISO 2015 All rights reservedBS EN ISO 1683:2015This page deliberately left blankThis page deliberately left blankBSI is the national body respon

41、sible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chis

42、wick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and r

43、efined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting o

44、ur website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need inte

45、rnational and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to

46、British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial disc

47、ounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To fin

48、d out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available

49、, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the da