BS EN 62271-205-2008 High-voltage switchgear and controlgear - Compact switchgear assemblies for rated voltages above 52 kV《高压开关装置和控制器 额定电压大于52kV的组合开关装置附件》.pdf

《BS EN 62271-205-2008 High-voltage switchgear and controlgear - Compact switchgear assemblies for rated voltages above 52 kV《高压开关装置和控制器 额定电压大于52kV的组合开关装置附件》.pdf》由会员分享，可在线阅读，更多相关《BS EN 62271-205-2008 High-voltage switchgear and controlgear - Compact switchgear assemblies for rated voltages above 52 kV《高压开关装置和控制器 额定电压大于52kV的组合开关装置附件》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 62271-205:2008High-voltage switchgear and controlgear Part 205: Compact switchgear assemblies for rated voltages above 52 kVICS 29.130.10; 29.130.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g4

2、0g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 62271-205:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2008 BSI 2008ISBN 978 0 580 56281 5National forewordThis British Standard is the UK implementati

3、on of EN 62271-205:2008. It is identical to IEC 62271-205:2008.The UK participation in its preparation was entrusted by Technical Committee PEL/17, Switchgear, controlgear, and HV-LV co-ordination, to Subcommittee PEL/17/1, High-voltage switchgear and controlgear.A list of organizations represented

4、on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrige

5、nda issued since publicationDate CommentsEUROPEAN STANDARD EN 62271-205 NORME EUROPENNE EUROPISCHE NORM April 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue

6、 de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62271-205:2008 E ICS 29.130.10; 29.130.99 English version High-voltage switchgear and controlgear - Part 205: Compact switchgear assemblies fo

7、r rated voltages above 52 kV (IEC 62271-205:2008) Appareillage haute tension - Partie 205: Ensembles dappareillages compacts de tensions assignes suprieures 52 kV (CEI 62271-205:2008) Hochspannungs-Schaltgerte und -Schaltanlagen - Teil 205: Kompakte Schaltanlagenanordnungen fr Bemessungsspannungen b

8、er 52 kV (IEC 62271-205:2008) This European Standard was approved by CENELEC on 2008-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-d

9、ate lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation unde

10、r the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Fran

11、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 17C/418/FDIS, future edition 1 of IEC 62271-205, prepa

12、red by SC 17C, High-voltage switchgear and controlgear assemblies, of IEC TC 17, Switchgear and controlgear, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62271-205 on 2008-03-01. This standard is to be used in conjunction with EN 62271-1:2007, to which it refers a

13、nd which is applicable, unless otherwise specified. In order to simplify the indication of corresponding requirements, the same numbering of clauses and subclauses is used as in EN 62271-1. Amendments to these clauses and subclauses are given under the same numbering, whilst additional subclauses ar

14、e numbered from 101. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow)

15、2011-03-01 Annexes ZA and ZB have been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62271-205:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 62271-205:2008 2 CONTENTS 1 General 5 1.1 Scope5 1.2 Normative references 6 2 Norma

16、l and special service conditions7 3 Terms and definitions .7 3.1 General terms .7 3.2 Compact switchgear assembly 8 4 Rating 8 4.1 Rated voltage (Ur) .8 4.2 Rated insulation level 9 4.3 Rated frequency (fr).9 4.4 Rated normal current (Ir) and temperature rise 9 4.5 Rated short-time withstand current

17、 (Ik) 9 4.6 Rated peak withstand current (Ip) 9 4.7 Rated duration of short circuit (tk)9 4.8 Rated supply voltage of closing and opening devices and of auxiliary and control circuits (Ua)9 4.9 Rated supply frequency of closing and opening devices and of auxiliary circuits 9 5 Design and constructio

18、n .10 5.3 Earthing of switchgear and controlgear.10 5.101 Earthing of compact switchgear assemblies and their controlgear.10 5.102 Pressure relief devices .10 5.10 Nameplates 10 5.12 Position indication 10 5.103 Locking devices for maintenance operation 10 5.104 Movement of pressurized devices .11 5

19、.105 Isolating distance for maintenance11 6 Type tests 11 6.1 General 11 6.2 Dielectric tests12 6.3 Radio interference voltage (r.i.v.) test .12 6.4 Measurement of the resistance of circuits .13 6.5 Temperature-rise tests13 6.6 Short-time withstand current and peak withstand current tests13 6.101 Me

20、chanical and environmental tests .14 7 Routine tests 16 7.1 Dielectric test on the main circuit 16 7.2 Tests on auxiliary and control circuits .16 7.3 Measurement of the resistance of the main circuit 16 7.101 Functional tests on auxiliary and control circuits .16 8 Guide to the selection of switchg

21、ear and controlgear16 8.101 Guide to the selection of compact switchgear assemblies.16 9 Information to be given with enquiries, tenders and orders .17 BS EN 62271-205:2008 3 10 Transport, storage, installation, operation and maintenance .17 10.1 Conditions during transport, storage and installation

22、 .17 10.2 Installation 17 10.3 Operation 17 10.4 Maintenance17 11 Safety.17 Annex AA (informative) Explanations of compact switchgear assemblies .18 Bibliography22 Figure AA.1 Example for type 1 .20 Figure AA.2 Example for type 2 .20 Figure AA.3 Example for type 3 .21 Figure AA.4 Example for type 3

23、.21 Table 101 Type tests on the compact switchgear assembly .11 Annex ZA (normative) Normative references to international publications with theircorresponding European publications.23BS EN 62271-205:2008 4 Annex ZB (informative) A-deviations25HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 205: Compac

24、t switchgear assemblies for rated voltages above 52 kV 1 General 1.1 Scope This part of IEC 62271 applies to compact switchgear assemblies consisting of at least one switching device directly connected to, or sharing components with, one or more other devices such that there is an interaction betwee

25、n the functions of the individual devices. Such assemblies are made up of devices defined in 1.101 and are designed, tested and supplied for use as a single unit. The interaction between devices may be due to proximity, sharing of components or a combination of both. The assemblies may contain compo

26、nents of air insulated switchgear (AIS) only or a combination of AIS and gas insulated switchgear (GIS), so called mixed technology switchgear (MTS) and may be delivered entirely prefabricated or partially assembled. It is not possible to define all potential arrangements of compact switchgear assem

27、blies however four examples are shown for information in Annex A. These compact switchgear assemblies are for indoor and/or outdoor installations in systems having rated voltages above 52 kV and service frequencies of 50 Hz and 60 Hz. This standard covers the influence on performance of the interact

28、ions between devices within compact switchgear assemblies and defines ratings and test procedures for these assemblies. IEC 62271-1 is applicable if not stated otherwise. This standard does not apply to switchgear assemblies consisting solely of GIS which are covered by 62271-203. 1.101 Objective Th

29、e objective of this standard is to respond to the increasing use of compact switchgear assemblies that perform the functions of a number of separate devices and their controlgear. Numerous arrangements are possible and this standard provides guidance on basic types of assemblies which might be envis

30、aged. As there are potential interactions between devices within such assemblies, it is necessary to consider the standardization requirements for the assembly in its entirety. The devices, defined by IEC standards, which may form part of a compact switchgear assembly are listed below: BS EN 62271-2

31、05:2008 5 Switching devices: Circuit-breakers IEC 62271-100 Disconnectors/Earthing switches IEC 62271-102 Switches IEC 60265-2 Disconnecting circuit-breakers IEC 62271-108 Devices: Instrument transformers Current transformers IEC 60044-1, IEC 60044-8 Voltage transformers IEC 60044-2, IEC 60044-5, IE

32、C 60044-7 Combined transformers IEC 60044-3 Surge arresters IEC 60099-4 Bushings IEC 60137 Insulators IEC 61462, IEC 62155 Cable connections IEC 62271-209 Transformer connections IEC 61639 Each switching device, device and their controlgear forming part of a compact switchgear assembly shall comply

33、with the relevant individual standard. If part of the compact switchgear assembly is formed by metal enclosed switchgear devices the requirements of IEC 62271-203 apply. Compact switchgear assemblies, as defined in this standard, are considered to be a single product with a single serial number and

34、one set of documentation. 1.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

35、. IEC 60044-1, Instrument transformers Part 1: Current transformers IEC 60044-2, Instrument transformers Part 2: Inductive voltage transformers IEC 60044-3, Instrument transformers Part 3: Combined transformers IEC 60044-5, Instrument transformers Part 5: Capacitor voltage transformers IEC 60044-7,

36、Instrument transformers Part 7: Electronic voltage transformers IEC 60044-8, Instrument transformers Part 8: Electronic current transformers IEC 60050-441, International Electrotechnical Vocabulary Chapter 441: Switchgear, controlgear and fuses IEC 60099-4, Surge arresters Part 4: Metal-oxide surge

37、arresters without gaps for a.c. systems IEC 60137, Insulated bushings for alternating voltages above 1 000 V BS EN 62271-205:2008 6 IEC 60265-2, High-voltage switches Part 2: High-voltage switches for rated voltages of 52 kV and above IEC 62271-209, High-voltage switchgear and controlgear Part 209:

38、Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV Fluid-filled and extruded insulation cables Fluid-filled and dry-type cable-terminations IEC 61462, Composite hollow insulators Pressurized and unpressurized insulators for use in electrical equipment with r

39、ated voltage greater than 1 000 V Definitions, test methods, acceptance criteria and design recommendations IEC/TR 61639, Direct connection between power transformers and gas-insulated metal-enclosed switchgear for rated voltages of 72,5 kV and above IEC 61936-1, Power installations exceeding 1 kV a

40、.c. Part 1: Common rules IEC 62155, Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V IEC 62271-1, High-voltage switchgear and controlgear Part 1:Common specifications IEC 62271-100, High-voltage switchgear and

41、controlgear Part 100: High-voltage alternating-current circuit-breakers IEC 62271-102, High-voltage switchgear and controlgear Part 102: Alternating current disconnectors and earthing switches IEC 62271-108, High-voltage switchgear and controlgear Part 108: High-voltage alternating current disconnec

42、ting circuit-breakers for rated voltages of 72,5 kV and above IEC 62271-203, High-voltage switchgear and controlgear Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV 2 Normal and special service conditions Clause 2 of IEC 62271-1 is applicable. 3 Terms and definitions

43、 For the purposes of this document, the terms and definitions of IEC 60050 (441), IEC 62271-1 and the publications mentioned in 1.2 apply. 3.1 General terms 3.1.101 connected position (of a removable part) position of a removable part in which it is fully connected for its intended function IEV 441-

44、16-25 BS EN 62271-205:2008 7 3.1.102 disconnected position (of a withdrawable part) position of a withdrawable part in which an isolating distance or segregation is established in all the circuits of the withdrawable part, that part remaining mechanically attached to the assembly IEV 441-16-28 NOTE

45、1 The auxiliary circuits may not be disconnected in this position. NOTE 2 This position may not be one in which it is safe to work on the withdrawn (moved) part. 3.2 Compact switchgear assembly Subclause 3.2 of IEC 62271-1 is applicable with the following addition: A compact switchgear assembly cons

46、ists of at least one switching device directly connected to, or sharing components with, one or more other devices such that there is an interaction between the functions of the individual devices. NOTE 1 A compact switchgear assembly may be mounted on one or more structures but it is only intended

47、for installation and operation as a single, complete unit. NOTE 2 Interaction is the transfer of stresses (e.g. electrical, mechanical and thermal) between the individual devices. 4 Rating Clause 4 of IEC 62271-1 is partly applicable with the following distinctive features: The rating of a compact s

48、witchgear assembly and its controlgear comprise the following : a) rated voltage (Ur); b) rated insulation level; c) rated frequency (fr); d) rated normal current (lr) (for main circuits); e) rated short-time withstand current (Ik) (for main and earthing circuits); f) rated peak withstand current (I

49、p) (for main and earthing circuits); g) rated duration of short-circuit (tk); and as applicable h) rated values of the devices of the compact switchgear assembly, including their operating devices (supply voltage and frequency), auxiliary and control equipment. The ratings of the compact switchgear assembly shall be assigned to ensure that operation of the assembly within its assigned ratings does not expose any individual device to conditions which