BS EN 61753-2-1-2001 Fibre optic interconnecting devices and passive components performance standard - Fibre optic connectors terminated on single-mode fibre for category U Uncontr.pdf

《BS EN 61753-2-1-2001 Fibre optic interconnecting devices and passive components performance standard - Fibre optic connectors terminated on single-mode fibre for category U Uncontr.pdf》由会员分享，可在线阅读，更多相关《BS EN 61753-2-1-2001 Fibre optic interconnecting devices and passive components performance standard - Fibre optic connectors terminated on single-mode fibre for category U Uncontr.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 61753-2-1:2001 IEC

2、61753-2-1:2000 The European Standard EN 61753-2-1:2000 has the status of a British Standard ICS 33.180.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Fibre optic interconnecting devices and passive components performance standard Part 2-1: Fibre optic connectors terminated

3、 on single-mode fibre for category U Uncontrolled environmentThis British Standard, having been prepared under the direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 April 2001 BSI 04-2001 ISBN 0 580 36897 1 BS

4、 EN 61753-2-1:2001 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard is the official English language version of EN 61753-2-1:2000. It is identical with IEC 61753-2-1:2000. The UK participation in its preparation was entrusted by Technical Committee G

5、EL/86, Fibre optics, to Subcommittee GEL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the

6、 UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number

7、. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an

8、annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Corr

9、espondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does n

10、ot of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 18, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued

11、.EUROPEAN STANDARD EN 61753-2-1 NORME EUROPENNE EUROPISCHE NORM November 2000 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 20

12、00 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61753-2-1:2000 E ICS 33.180.20 English version Fibre optic interconnecting devices and passive components performance standard Part 2-1: Fibre optic connectors terminated on singl

13、e-mode fibre for category U - Uncontrolled environment (IEC 61753-2-1:2000) Norme de qualit de fonctionnement des dispositifs dinterconnexion et composants passifs fibres optiques Partie 2-1: Connecteurs fibres optiques raccords une fibre monomode pour la catgorie U - Environnement non contrl (CEI 6

14、1753-2-1:2000) Lichtwellenleiter-Verbindungselemente und passive Bauteile - Betriebsverhalten Teil 2-1: Einmoden-Lichtwellenleiter- Steckverbinder fr die Kategorie U - Unkontrollierte Umgebung (IEC 61753-2-1:2000) This European Standard was approved by CENELEC on 2000-08-01. CENELEC members are boun

15、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Ce

16、ntral Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same

17、status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Foreword The

18、 text of document 86B/1314/FDIS, future edition 1 of IEC 61753-2-1, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC- CENELEC parallel vote and was approved by CENELEC as EN 61753-2-1 on 2000-08-01. The following dat

19、es were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2001-05-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2003-08-01 Annexes designated “normati

20、ve“ are part of the body of the standard. In this standard, annexes A, B and ZA are normative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61753-2-1:2000 was approved by CENELEC as a European Standard without any modification. _ Page2 EN6175321

21、:2000 BSI 04-2001 CONTENTS Page Clause 1 Scope 4 2 Normative references. 4 3 Definitions 5 4 Tests . 6 5 Test report. 6 6 Reference components 6 7 Performance requirements . 6 7.1 Dimensions. 6 7.2 Sample size, sequencing and groupings 6 7.3 Performance details 7 Annex A (normative) Sample size, seq

22、uencing and grouping requirements . 15 Annex B (normative) Reference components 16 Annex ZA (normative) Normative references to international publications with their corresponding European publications 17 Page3 EN6175321:2000 BSI 04-2001 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS PER

23、FORMANCE STANDARD Part 2-1: Fibre optic connectors terminated on single-mode fibre for category U Uncontrolled environment 1 Scope This part of IEC 61753 contains the minimum requirements and severities which a single-mode connector/cable assembly must satisfy in order to be considered as meeting ca

24、tegory U (uncontrolled environment) of IEC 61753-1, as defined in annex A of IEC 61753-1. This standard contains optional grades of optical performance for the attenuation random mate and return loss tests. 2 Normative references The following normative documents contain provisions which, through re

25、ference in this text, constitute provisions of this part of IEC 61753. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IEC 61753 are encouraged to investigate the possibility of applying the

26、 most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60793-1-1, Optical fibres Part 1: Generic specificatio

27、n Section 1: General IEC 61300-2-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-1: Tests Vibration (sinusoidal) IEC 61300-2-2, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-2: Tests

28、Mating durability IEC 61300-2-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-4: Tests Fibre/cable retention IEC 61300-2-5, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-5: Tests Tors

29、ion/twist IEC 61300-2-6, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-6: Tests Tensile strength of coupling mechanism IEC 61300-2-7, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-7: T

30、ests Bending moment IEC 61300-2-12, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-12: Tests Impact Page4 EN6175321:2000 BSI 04-2001 IEC 61300-2-17, Fibre optic interconnecting devices and passive components Basic test and measurement procedur

31、es Part 2-17: Tests Cold IEC 61300-2-18, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-18: Tests Dry heat High temperature endurance IEC 61300-2-19, Fibre optic interconnecting devices and passive components Basic test and measurement procedu

32、res Part 2-19: Tests Damp heat (steady state) IEC 61300-2-21, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-21: Tests Composite temperature-humidity cyclic test IEC 61300-2-22, Fibre optic interconnecting devices and passive components Basic

33、test and measurement procedures Part 2-22: Tests Change of temperature IEC 61300-2-27, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-27: Tests Dust Laminar flow IEC 61300-2-42, Fibre optic interconnecting devices and passive components Basic

34、test and measurement procedures Part 2-42: Tests Static side load for connectors IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examination and measurements Attenuation IEC 61300-3-6, Fibre optic interconnecting devices and p

35、assive components Basic test and measurement procedures Part 3-6: Examinations and measurements Return loss IEC 61300-3-34, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-34: Examinations and measurements Attenuation of random mated connectors

36、 3 Definitions For the purpose of this part of IEC 61753, the following definitions apply. 3.1 loss variation attenuation from the value measured before the commencement of the test 3.2 sample connector set, defined as the complete set of connector components required to provide demountable coupling

37、 between one or more pairs of optical fibres Page5 EN6175321:2000 BSI 04-2001 4 Tests All test methods are in accordance with a specific IEC 61300 part. The samples shall be terminated onto single-mode fibre as per IEC 60793-1-1, category B.1.1, in either secondary coated or reinforced cable format.

38、 Each test defines the number of samples to be evaluated. The connector pairs used for each test are intended to be previously unstressed new samples, but may be selected from previously used samples, if so desired. All optical testing shall be carried out at 1 550 nm 30 nm, unless otherwise specifi

39、ed. Change in attenuation is, for the purpose of the test, defined as peak to peak variation. 5 Test report Fully documented test reports and supporting evidence shall be prepared and made available for inspection as evidence that the tests have been carried out and complied with. 6 Reference compon

40、ents Where the test methods used within this standard require the use of reference components, they shall have characteristics as defined in annex B. 7 Performance requirements 7.1 Dimensions Dimensions shall comply with either the appropriate IEC interface standard or with those given in appropriat

41、e manufacturers drawings, where the IEC interface standard does not exist or cannot be used. 7.2 Sample size, sequencing and groupings The length of cable (or fibre) on each side of the connector set should be 1,5 m minimum. The sample sizes, sequencing and grouping to be used for the tests shall be

42、 as defined in annex A. Samples may either be new product or sourced from a previous test. Page6 EN6175321:2000 BSI 04-2001 7.3 Performance details No. Test Requirements Details 1 Attenuation (reference) 0,50 dB 1 330 nm 30 nm and 1 550 nm 30 nm IEC 61300-3-4 Insertion Method B Launch mode condition

43、s: Only the fundamental mode shall propagate at the connector interface and at the detector Source stability 0,05 dB over the measuring period or at least 1 h Source characteristics: S4 for 1 310 nm S5 for 1 550 nm Power meter: D2 Reference component: As per annex B Specimen shall be optically funct

44、ioning Preconditioning procedure: Clean the mechanical and optical alignment parts of the specimen according to the manufacturers instructions. 2a Return loss (branching device method) Class S 26 dB Class T 35 dB Class R 40 dB 1 330 nm 30 nm and 1 550 nm 30 nm IEC 61300-3-6 Method 1 Launch fibre len

45、gth: L 2 m Source stability: 0,20 dB over the measuring period or at least 1 h Source spectral width: To be decided Detector sensitivity: To be decided Detector linearity: To be decided Reference components: As per annex B Specimen shall be optically functioning Preconditioning procedure: Clean the

46、mechanical and optical alignment parts of the specimen according to the manufacturers instructions. 2b Return loss (OTDR method) Class U 50 dB Class V 60 dB (mated and unmated) IEC 61300-3-6 Method 2 Launch fibre length: L1 500 m, L2 6 m, L3 6 m Spectral width: To be decided Pulse duration: To be de

47、cided Specimen shall be optically functioning Preconditioning procedure: Clean the mechanical and optical alignment parts of the specimen according to the manufacturers instructions. Page7 EN6175321:2000 BSI 04-2001 3 Attenuation (random mate) Grade P Mean 0,35 dB Max 1,00 dB for 97 % of mating comb

48、inations Grade Q Mean 0,30 dB Max. 0,60 dB for 99 % of mating combinations IEC 61300-3-34 Launch mode conditions: Only the fundamental mode shall propagate at the connector interface and at the detector Source characteristics: S5 for 1 550 nm Power meter D2 Attenuation measurements shall be made usi

49、ng randomly selected specimens Specimen shall be optically functioning Preconditioning procedure: Clean the mechanical and optical alignment parts of the specimen according to the manufacturers instructions. 4V i b r a t i o n (sinusoidal) Allowable change in attenuation: 0,20 dB 1 550 nm 30 nm Attenuation shall be measured before, during and a