BS EN 61269-1-1997 Fibre optic terminus sets - Generic specification《光纤端件 总规范》.pdf

《BS EN 61269-1-1997 Fibre optic terminus sets - Generic specification《光纤端件 总规范》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61269-1-1997 Fibre optic terminus sets - Generic specification《光纤端件 总规范》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 61269-1:1997 IEC 1269-1: 1994 Fibre optic terminus sets Part 1: Generic specification The European Standard EN61269-1:1997 has the status of a British Standard ICS 33.180.10BSEN61269-1:1997 This British Standard, having been prepared under the directionof the Electrotechnical

2、Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15June 1997 BSI 02-1999 ISBN 0 580 27728 3 National foreword This British Standard is the English language version of EN61269-1:1997. It is identical with IEC1269-1:1994. The UK participation in its prepara

3、tion was entrusted by Technical Committee EPL/86, Fibre optics, to Subcommittee EPL/86/2, Interconnecting devices and passive components, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpreta

4、tion, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which

5、 implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not pu

6、rport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front

7、 cover, pages i and ii, theEN title page, pages2 to16, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd

8、. No. Date CommentsBSEN61269-1:1997 BSI 02-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 61269-1 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN61269-1 February1997 ICS33.180.20 English version Fibre optic terminus sets Part 1: Generic specification (I

9、EC 1269-1:1994) Jeux dembouts pour fibres optiques Partie1:Spcification gnrique (CEI1269-1:1994) Kontakteinstze fr Lichtwellenleiter Teil1:Fachgrundspezifikation (IEC1269-1:1994) This European Standard was approved by CENELEC on1996-10-01. CENELEC members are bound to comply with the CEN/CENELEC Int

10、ernal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC

11、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN

12、ELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization

13、 Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN61269-1:1997 EEN61269-1:1

14、997 BSI 02-1999 2 Foreword The text of the International Standard IEC1269-1:1994, prepared by SC86B, Fibre optic interconnecting devices and passive components, of IECTC86, Fibre optics, was submitted to the formal vote and was approved by CENELEC as EN61269-1 on1996-10-01 without any modification.

15、The following dates were fixed: Annexes designated “normative” are part of the body of the standard. Annexes designated “informative” are given for information only. In this standard, Annex ZA is normative and Annex A is informative. Annex ZA has been added by CENELEC. Endorsement notice The text of

16、 the International Standard IEC1269-1:1994 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 General 3 1.1 Scope 3 1.2 Normative references 3 1.3 Definitions 3 1.4 Abbreviations 4 2 Requirements 4 2.1 Qualification 4 2.2 Classification 4 2.3 Document

17、ation 6 2.4 Design and construction 7 2.5 Quality assessment 8 2.6 Identification and marking 8 3 Quality assessment procedures 8 3.1 Primary stage of manufacture 9 3.2 Structural similarity 9 3.3 Qualification approval procedures 9 Page 3.4 Quality conformance inspection 10 3.5 Certified records of

18、 released lots 12 3.6 Delayed deliveries 12 3.7 Release before completion of group B tests 12 3.8 Measurement and test procedures 12 3.9 Alternative test methods 12 3.10 Unchecked parameters 12 Annex A (informative) Standard environmental categories 13 Annex ZA (normative) Normative references toint

19、ernationalpublications with theircorresponding European publications Inside back cover Table 1 Example of a typical terminus-set classification 5 Table A.1 Fixed sample test schedule for qualification approval Environmental category 1 13 Table A.2 Lot-by-lot inspection schedule Environmental categor

20、y 1 (groups A and B) 13 Table A.3 Periodic inspection schedule Environmental category 1 (groups C and D) 14 Table A.4 Fixed sample test schedule for qualification approval Environmental category 2 14 Table A.5 Lot-by-lot inspection schedule Environmental category 2 (groups A and B) 14 Table A.6 Peri

21、odic inspection schedule Environmental category 2 (groups C and D) 15 Table A.7 Fixed sample test schedule for qualification approval Environmental category 3 15 Table A.8 Lot-by-lot inspection schedule Environmental category 3 (groups A and B) 16 Table A.9 Periodic inspection schedule Environmental

22、 category 3 (groups C and D) 16 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-09-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-09-01EN61269-1:1

23、997 BSI 02-1999 3 1 General 1.1 Scope This part of IEC1269 applies to fibre optic terminus sets for all types, sizes and structures of fibres and cables. It includes: terminus set requirements; quality assessment procedures. 1.2 Normative references The following normative documents contain provisio

24、ns which, through reference in this text, constitute provisions of this part of IEC1269. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this part of IEC1269 are encouraged to investigate the possibili

25、ty of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC QC 001001:1986, Basic Rules of the IEC Quality Assessment System for Electronic Components (IECQ). IEC QC 001002:1986, Rules o

26、f Procedure of the IEC Quality Assessment System for Electronic Components (IECQ). IEC 27, Letter symbols to be used in electrical technology. IEC 68, Environmental testing. IEC 410:1973, Sampling plans and procedures for inspection by attributes. IEC 617, Graphical symbols for diagrams. IEC 695-2-2

27、:1991, Fire hazard testing Part2:Test methods Section2: Needle-flame test. IEC 874-1:1993, Connectors for optical fibres and cables Part1: Generic specification. IEC 1300:199X, Basic measurement and test procedures for passive fibre optic components (underconsideration). ISO 129:1985, Technical draw

28、ings dimensioning General principles, definitions, methods of execution and special indications. ISO 286-1:1988, ISO system of limits and fits Part1: Bases of tolerances, deviations and fits. ISO 370:1975, Toleranced dimensions Conversion from inches into millimetres and vice versa. ISO 1101:1983, T

29、echnical drawings Geometrical tolerancing Tolerances of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings. 1.3 Definitions For the purposes of this part of IEC1269, the following definitons apply. 1.3.1 terminus an optical component which terminates

30、an optical fibre within a connector and which is both removable from and replaceable in the connector. A specific terminus may be used in a wide variety of connector styles (e.g. circular, rectangular, rack and panel, hybrid, etc.) which may be qualified under other specification systems (e.g. speci

31、fications for electrical connectors) 1.3.2 terminus set the two mateable termini. Generally, a set consists of a terminus pin and a terminus socket 1.3.3 mechanically intermateable termini termini which are capable of being mechanically mated. Performance or intermountability are not requirements fo

32、r intermateabilityEN61269-1:1997 4 BSI 02-1999 1.3.4 interchangeable termini termini which meet the same assessed performance specification and are intermountable. Interchangeability applies to a terminus set only since individual termini are not necessarily intermateable 1.3.5 intermountable termin

33、i termini which have identical mounting parameters. Intermateability or interchangeability are not requirements for intermountability 1.3.6 termini control dimensions those termini dimensions which control intermateability and intermountability 1.4 Abbreviations 2 Requirements 2.1 Qualification Comp

34、onents covered by this specification shall be authorized by the NSI for listing on the QPL under the qualification procedure in accordance with11.3.1 of QC001002. 2.2 Classification Termini are classified, either totally or in part, by the following categories: type; arrangement; style; variant; cli

35、matic category; environmental category; assessment level. SeeTable 1 for an example of a complete terminus-set classification. 2.2.1 Type Terminus sets shall be classified by type. Type is defined by three elements the type name, the configuration, and the control dimensions. Examples of terminus-se

36、t names: FOTS, gauge 8; subminiature D, gauge 16. Examples of terminus-set configurations: pin/socket; pin/pin. NSI: QPL: National Supervising Inspectorate; Qualified Products List.EN61269-1:1997 BSI 02-1999 5 Table 1 Example of a typical terminus-set classification 2.2.2 Arrangement Terminus sets s

37、hall be classified by arrangement. Arrangement category defines the delivered terminus-set form. Examples of arrangements: kit; pigtail. 2.2.3 Style Terminus sets shall be classified by style. Style is defined by the fibre retention technology, the cable retention technology (where applicable), the

38、optical coupling technology, and the alignment technology. Examples of fibre retention technologies: adhesive; crimp. Examples of cable retention technologies (whereapplicable): adhesive; crimp. Examples of optical coupling technologies: non-butting; butting; expanded beam. Examples of alignment tec

39、hnologies: clearance fit; resilient bushing; resilient tip; spherical. 2.2.4 Variant Termini shall be classified by variant. The variant classification consists of the variant, identification number (see2.6.1). Type Name: FOTS, Gauge 8 Configuration: pin/socket Control dimensions: pin; socket; see F

40、igure 1* see Figure 2* Arrangement: Kit Style: Fibre retention: Cable retention: Optical coupling: Alignment: adhesive crimp butting resilient socket bushing Variants: see table of variant ID numbers Climatic category: 55/125/21 Environmental category: non-standard Assessment level: A NOTE*indicates

41、 figures in a hypothetical detail specification.EN61269-1:1997 6 BSI 02-1999 2.2.5 Climatic category Terminus sets may be classified by climatic category as defined inAppendix A of IEC68-1. The following are preferred values: 2.2.6 Environmental Category Terminus sets may be classified by environmen

42、tal category. Environmental category corresponds to the test schedules used for quality assessment. Environmental category standards are given inAnnex A. 2.2.7 Assessment level Adaptors shall be classified by assessment level. Assessment level is designated by a capital letter. The following assessm

43、ent level standards may be used: Assessment level A Assessment level B Assessment level C When an assessment level other than one of the above standards is used, it shall be designated with the capital letter X. 2.3 Documentation 2.3.1 Symbols Graphical and letter symbols, as given in IEC27 and IEC6

44、17 shall, as applicable, be used in detail specifications. 2.3.2 Specification system This specification is part of the three-level IEC specification system and includes blank detail specifications. Subsidiary specifications consist of detail specifications. Low temperature C High temperature C Damp

45、 heat duration days 5 10 25 40 55 65 + 30 + 40 + 55 + 70 + 85 + 100 + 125 + 155 + 175 + 200 4 10 21 56 Group A inspection: Group B inspection: Group C inspection: Group D inspection: inspection level II, AQL =4% inspection level II, AQL =4% 24 month periods 48 month periods Group A inspection: Group

46、 B inspection: Group C inspection: Group D inspection: inspection level II, AQL =1% inspection level II, AQL =1% 18 month periods 36 month periods Group A inspection: Group B inspection: Group C inspection: Group D inspection: inspection level II, AQL=0,4% inspection level II, AQL=0,4% 12 month peri

47、ods 24 month periodsEN61269-1:1997 BSI 02-1999 7 2.3.3 Drawings 2.3.3.1 Projection system Detail specifications shall use either first angle or third angle projection. All drawings within one detail specification shall use the same projection system and the drawings shall state which system is used.

48、 2.3.3.2 Dimensional system All dimensions shall comply with ISO129, ISO286-1 and ISO1101. The metric system shall be used in detail specifications. Inch dimensions may be added for information. Conversion between systems of units shall comply with ISO370. 2.3.3.3 Control dimensions The detail speci

49、fication shall define the termini control dimensions and the counterpart component dimensions (see3.3.4). The counterpart component dimensions shall define as a minimum: a) a fully toleranced cavity; b) the dimensions of those features, as required, which control termini alignment, including: angular misalignment; radial offset; axial separation. 2.3.4 Measurements 2.3.4.1 Measurement methods The detail spe